Polycom RSS 2000 - Manual

Polycom RSS 2000

Polycom RSS 2000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
Page: / 24

Table of Contents:

  • Page 2 – Unpacking and Installing the RSS 2000; To connect to the power source, insert the power cable into the
  • Page 3 – Initial RSS 2000 IP Configuration; The system is shipped with a default IP address:
  • Page 5 – Changing the initial IP address via an RS232 Console or Telnet; reset password
  • Page 6 – Archive view How many streaming can be
  • Page 7 – Network TCP/UDP ports used by RSS2000; Usage Type
  • Page 10 – , New Systems – New Installations; Keycode definition; Click; Polycom Resource Center; , go to the PRC and under product activation:
  • Page 13 – , Current Install base (Existing systems that require upgrade); Package Name; With full function –support English and Japanese; Please refer same introduction in the part of “; new installation
  • Page 14 – : Download upgrade package to RSS; the; : Activate your RSS by Keycode
  • Page 15 – Now you RSS can support; English, Chinese and Japanese; . If you want additional language; “Additional
  • Page 18 – Additional Language Support; Image version check
Loading the manual

DOC2207A RSS 2000 V3.0 Getting Started guide - Release Note - Final - February 26, 2008.doc

Polycom ™ RSS 2000 V3.0.0.000
Getting Started Guide


General Safety Precautions


Follow these rules to ensure general safety:

• Keep the area around the Polycom RSS 2000 unit clean, free of clutter
and well ventilated.

• Decide on a suitable location for the equipment rack that will hold
the RSS 2000 unit and is near a grounded power outlet.

• • Use a regulating uninterruptible power supply (UPS) to protect the
RSS 2000 unit from power surges and voltage spikes, and to keep it
operating in case of a power failure.

Hardware Specification

Pentium 4, 2.8Mhz,2G RAM,250G Hardisk.

• Form Factor: 1U 19” rack mount

• Height: 1.73” (44 mm)

• Width: 16.83” (430 mm)

• Depth: 15.35” (390 mm)

• Gross Weight: 22.4 lbs (10.2 kg)

• Power Supply: Thermal controlled 220W
ATX AC power supply w/PFC

• AC Voltage: 100 - 240 VAC, 60-50 Hz, 5-3
Amps

XP OS

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Unpacking and Installing the RSS 2000; To connect to the power source, insert the power cable into the

DOC2207A RSS 2000 V3.0 Getting Started guide - Release Note - Final - February 26, 2008.doc Preparations Obtain the following information from your network administrator: • RSS 2000 unit, Subnet Mask and Default Gateway IP addresses • Gatekeeper IP address, Prefix, and E.164 of the RSS 2000. Unpacki...

Page 3 - Initial RSS 2000 IP Configuration; The system is shipped with a default IP address:

DOC2207A RSS 2000 V3.0 Getting Started guide - Release Note - Final - February 26, 2008.doc Initial RSS 2000 IP Configuration The system is shipped with a default IP address: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 There are two ways to change the initial IP address...

Page 5 - Changing the initial IP address via an RS232 Console or Telnet; reset password

DOC2207A RSS 2000 V3.0 Getting Started guide - Release Note - Final - February 26, 2008.doc 2.Changing the initial IP address via an RS232 Console or Telnet Another option to modify the IP address of the RSS 2000 is using the RS232 console. 1.Connect to the RS232 port – and activate the console (960...

Other Polycom Models

All Polycom Other