Page 3 - Contents; Replacing Components
Contents 1 Contents KWS8000 Installation Installing the KWS8000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1General Installation Information . ....
Page 4 - Specifications
1–1 1 KWS8000 Installation This guide describes how you install the KWS8000. Installing the KWS8000 The KWS 8000 can be installed in a rack, on a flat surface or on a wall using the KWS8000 Wall Hanger. Before you start the installation, place the KSW 8000 on a stable flat surface in the selected lo...
Page 5 - General Installation Information; General Mounting Safety Precautions; Installing the KWS8000 in a Rack
Polycom KIRK Wireless Ser ver 8000 Installation Guide 1–2 General Installation Information The maximum number of KWS 8000 units that can be linked together depends on the mounting method and the maximum length of the link cable: • Rack mount: 8 units • Flat surface mount: 2 units • Wall mount: 1 uni...
Page 6 - Rack mounting Safety Precautions.
KWS8000 Installation 1–3 Rack mounting Safety Precautions. • Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them. • In a single rack installation, stabilizers should be attached to the rack. • In multiple rack inst...
Page 7 - Installing the KWS 8000 on a Flat Surface; Flat Surface Mounting Safety Precautions
Polycom KIRK Wireless Ser ver 8000 Installation Guide 1–4 Figure 1-1 Rack Installation Installing the KWS 8000 on a Flat Surface Before you start installation take notice of the following safety precautions. Flat Surface Mounting Safety Precautions • Ensure the surface can support the weight of the ...
Page 8 - Installing the KWS8000 on a Wall; Wall Mounting Safety Precautions
KWS8000 Installation 1–5 2 Before placing the unit, carefully turn it upside down and mount the four rubber pads supplied in the package. One must be placed at each corner of the bottom plate. 3 Place it on a clean, flat, horizontal surface. Installing the KWS8000 on a Wall Before you start installa...
Page 9 - Connecting the KWS8000 Cables; Cable Safety Precautions
Polycom KIRK Wireless Ser ver 8000 Installation Guide 1–6 2 Mount the wall hanger securely using four screws. Use rawlplugs, expansion bolts or other appropriate fastening methods in relation to the wall material. 3 Remove drilling dust, unpack the KWS8000, fit it into the wall hanger, and then fast...
Page 12 - Installing Interface Cards and CPU Cards; Safety Precautions
KWS8000 Installation 1–9 Figure 1-5 Storing room for two AC power adapters If more than two AC power adapters are used, these must be kept on a flat surface (same requirements as for the KWS8000 unit). In a rack installation the power adapters can be kept on a tray installed for the purpose provided...
Page 14 - Connecting Interface Cables
KWS8000 Installation 1–11 Figure 1-7 Installing CPU card 3 Plug the interface cables into the card as described in “Connecting Interface Cables” on page 1-11. 4 Connect the power and reboot the unit. Connecting Interface Cables The front interface of the KWS8000 is provided with connectors for the d...
Page 17 - Component Replacement
2–1 2 Replacing Components The KWS8000 is designed to minimize down-time. Several components can be replaced while the system is up. Component Replacement The following components are hot-swappable: • Interface cards • AC adapters The following require a power down of the system: • Backplane • CPU c...
Page 18 - Component Replacement Precautions; Replacing Interface and CPU cards
Polycom KIRK Wireless Ser ver 8000 Installation Guide 2–2 Component Replacement Precautions • Cards contain static sensitive circuitry and may be destroyed or damaged by electrostatic discharge (ESD.) • All maintenance tasks must be performed by qualified, authorized personnel only. • Use only origi...
Page 19 - Replacing the Backplane
Replacing Components 2–3 7 Plug the interface cables into the card. 8 Connect power and reboot the unit. Replacing the Backplane The backplane cannot be replaced on-site. The chassis will have to be returned for repair or be replaced with a new one. If a new chassis is to be installed, you can move ...
Page 20 - Regulator y Notices; International Regulator y and Product Information
3–1 3 Regulator y Notices This section contains important safety regulations for the KWS8000. International Regulator y and Product Information United States Federal Communication Commission (FCC) Part 15: Class A Statement . This equipment has been tested and found to comply with the limits for a C...
Page 23 - Important Safety Instructions and Product Information
Polycom KIRK Wireless Ser ver 8000 Installation Guide 3–4 Important Safety Instructions and Product Information Before using your telephone equipment, you should always follow basic safety instruction to reduce the risk of fire, electrical shock and injury to persons, and damage to property. 1 Read ...
Page 24 - Warning; Intrinsic safety
Regulator y Notices 3–5 Warning 1 Avoid using telephone during an electrical storm. There may be a risk of electrical shock from lightning 2 Do not use the telephone to report a gas leak in the vicinity of the leak 3 Do not place the unit near microwave ovens, radio equipment, or non-ground connecte...
Page 25 - Polycom® Product Warranty Statement
Polycom KIRK Wireless Ser ver 8000 Installation Guide 3–6 IC Note: Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term “IC...
Page 27 - END-USER LICENSE AGREEMENT FOR POLYCOM SOFTWARE
Polycom KIRK Wireless Ser ver 8000 Installation Guide 3–8 OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF POLYCOM OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABI...
Page 33 - Tables
KWS 8000 Installation and Configuration Guide 11 Tables Table 1-1 Physical dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1 Table 1-2 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1 Table 1-3...
Page 34 - Figures
Figures 11 Figures Figure 1-1 Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4 Figure 1-2 Wall hanger positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5 Figure 1-3 Fitting the kWS8000 into the wall ha...
Page 35 - Index
Index Index – 1 Index A AC power adapters 1–9 E Environment 1–1 F Flat surface installation 1–4 I Interface cable connection 1–11 Interface card installation 1–9 P Physical dimensions 1–1 Power cables, connecting 1–6 Power consumption 1–1 Power supply 1–1 R Rack installation 1–3 S Safety Cables 1–6 ...
