Page 3 - Operating Instructions; Table of Contents; LCD M
DRM-7000 Operating Instructions Table of Contents 1.0 FEATURES OF THE DRM-7000 DISC CHANGER .......................................................................... 1 1.1 F LEXIBLE U NIT D ESIGN ..........................................................................................................
Page 5 - Features of the DRM-7000 Disc Changer; Flexible Unit Design; installed together to meet a variety of needs.; Types of Disc Magazines; 0-Disc Hyper Magazine; Ease of Installation; control the Changer.
DRM-7000 Operating Instructions 1.0 Features of the DRM-7000 Disc Changer 1.1 Flexible Unit Design The Pioneer DRM-7000 Disc Changer is designed so that a various components may be installed together to meet a variety of needs. The Pioneer DRM-7000 provides easily, accessed bays on both the front an...
Page 7 - Precautions; Site
DRM-7000 Operating Instructions 2.0 Handling Precautions 2.1 Installation Site Select an installation site with a flat, solid surface. Check the area for the following conditions: • Avoid exposure to direct sunlight, spotlights or too near to a heater • Beware of high humidity locations or sites exp...
Page 8 - Offline; Removable Disc Magazines; Deciding on System Configuration; (refer to the configuration guide at the end of this manual).
DRM-7000 Operating Instructions benzine, thinner, insecticide or other strong chemicals as these may dissolve or discolor the cabinet surface. Some commercially produced chemical polishing clothes may be acceptable but read all instructions and warnings first. 2.5 Managing Offline Media The DRM-7000...
Page 9 - Installation; Examples of SCSI Cable Connections; Products Provided with the DRM-7000
DRM-7000 Operating Instructions • Two drives installed on separate cables • Both drives are connected to the internal daisy-chain board using the cables provided (it is necessary to purchase another SCSI cable to connect the Changer to the HOST) To install three or more drives or to use more than on...
Page 10 - 0-Disc Hyper Magazine Dust Cover; Products; The internal DVR drive may be used to read DVD and CD discs.
DRM-7000 Operating Instructions • 20-Disc Hyper Magazine Dust Cover • Operating Instructions • Warranty Information • Service Network Sheet 2.8 Add-On Products The following components may be purchased separately for use with the Pioneer DRM-7000 Changer. • 50-Disc Locking Magazine (DRM-AL751) This ...
Page 12 - Names and Functions of Individual Parts
DRM-7000 Operating Instructions 3.0 Names and Functions of Individual Parts - 8 -
Page 14 - Positioning the Changer; Attach the placement fixtures
DRM-7000 Operating Instructions 4.0 Installation 4.1 Positioning the Changer The instructions below lead through the physical installation of the DRM-7000. 1. Attach the placement fixtures To stabilize the Changer further, attach the placement fixtures at the corners of the unit • Always be sure to ...
Page 15 - Before Using the Changer for the First Time; Turn ON the power to the Changer
DRM-7000 Operating Instructions 3. Lock all four legs/wheels into place 4. Connect the power cord to the Changer • Insert the power cord into the rear of the changer before inserting the plug into the wall socket Caution: Always be sure to use only a power cord designed for use in that country. 4.2 ...
Page 16 - orange; green
DRM-7000 Operating Instructions 2. Loosen the shipping screws With the front access panel open, loosen the two screws located in the base • Screws are permanent to avoid becoming lost but must be loosened to operate the Changer • Tighten these screws before moving or transporting the Changer • Closi...
Page 17 - Changing the SCSI ID on a DRM-7000; change and the following message to appear on the LCD display.; Revision; Reading SCSI Drive IDs from the DRM-7000
DRM-7000 Operating Instructions 5. Connect the Changer Interface cable to the drive. • Confirm that the interface cable is connected to the correct bay Caution: Connecting the interface cable to an incorrect bay port results in damage to the discs. • Install an add-on connector board if necessary 4....
Page 18 - Connecting SCSI Cables; conditions listed below are met below attaching the cables.
DRM-7000 Operating Instructions SCSI buses allows duplicate SCSI IDs as long as the duplicates are assigned to separate buses. Even if none of the drives installed within the changer has been assigned the same SCSI ID, it is necessary to assign a different SCSI ID to any drives which share the same ...
Page 19 - Disc; Please review the insertion methods listed below.
DRM-7000 Operating Instructions Daisy-chain six internal readers and a recorder then connect the Changer – requires a cable for four drives Connect two readers and two recorders then connect the Changer – requires three separate SCSI controller cards 4.6 Inserting Disc Magazines Please review the in...
Page 21 - Locked – type
DRM-7000 Operating Instructions 5. Remove the magazine by flipping the handle out and pulling the unit towards you. Support the magazine so that it remains level as it slides off of the rails. 4.6.2 Inserting Discs Using a 20-Disc Hyper-Magazine Follow the directions below to insert discs in to a hy...
Page 22 - Slot
DRM-7000 Operating Instructions A similar message appears when a magazine is removed from the Changer. M1 Locked – type out If these messages appear repeatedly in rapid succession, the magazine is improperly inserted into the bay. Remove the magazine and remount the unit into the appropriate Changer...
Page 23 - disc; sequence from the lowest to the highest number.
DRM-7000 Operating Instructions Once the initialization is complete, the following message appears in the LCD display: Robotics readyDrive1 no disc The first line of the message refers to the status of the disc changer mechanism. The second line indicates the disc number and registers any loaded dis...
Page 24 - Mode; Administrator; Insert the key into the key switch located on the control panel.; Function; button to enter the System Administrator Mode.
DRM-7000 Operating Instructions 5.0 Operation The DRM-7000 supports two modes, User and System Administrator. Separating the operations into two modes prevents interference, conflicts, or clashes from occurring between commands issued from the host computer and commands entered at the Changer’s Cont...
Page 26 - Submode; Setup browser; Enter; Magazine – bay or; Example of Rear Bay selection:; Enter; Drive 1
DRM-7000 Operating Instructions Information submodes enable a System Administrator to check a Changer’s current settings or read the stored data. The System Administrator may also view a variety of Changer information without interfering with the control of the Changer from the host computer. Operat...
Page 27 - Example of Hyper Magazine Bay selection:
DRM-7000 Operating Instructions To change the selected bay, use the up and down arrow buttons. Example: arrow button Bay # 5 & # 6 flip unit arrow button Bay # 9 no component arrow button Bay # 15 & # 16 ID = ************ If the bay holds a drive, press Enter to display the SCSI ID, the term...
Page 28 - Example of Magazine Bay selection:
DRM-7000 Operating Instructions If the locking record log is empty, the following message appears: Locked – state When there are records in the memory, the following message appears: Uncertain – state Example of Magazine Bay selection: Press the up arrow button while the hyper magazine information d...
Page 29 - left arrow; A u t o p r o b i n g i s; A u t o p r o b i n g
DRM-7000 Operating Instructions The optional operations are as follows when scanning using the right arrow button: • Auto Probing – default set to OFF at time of shipment • Inquiry Change – default set to OFF at time of shipment • Free Message – default set to Off at time of shipment • Alert Buzzer ...
Page 36 - Up; Uncertain; PowerON time
DRM-7000 Operating Instructions # 1 2 3 , # 2 2 1 , # 2 5 8 , M 1 5 ( # 7 0 1 - # 7 5 0 ) , Press the Up arrow button H y p e r ( # 7 5 1 - # 7 7 0 ) ,e n d o f l i s t 5.2.4.2 Contents Request a Content log to review the number of filled and vacant slots within the combined magazines. F u l l s l o...
Page 37 - Drive Work Time; Elevation Done
DRM-7000 Operating Instructions Select Drive Work Time to reveal the total time each drive has been in opration. P o w e r O n - t i m e o r D r i v e w o r k - t i m e ? Press the Enter button D r i v e 1 w o r k s * * * * * * h o u r s * * m i n Press the Up arrow button D r i v e 2 w o r k s * * ...
Page 38 - Swap, Remove or Add some discs
DRM-7000 Operating Instructions E l e v a t i o n d o n e * * * * * * t i m e s Press Down or Up arrow button L o a d / U n l o a d d o n e * * * * * * t i m e s Press Down or Up arrow button M a i l s l o t d r i v e n * * * * * * t i m e s Press Down or Up arrow button H y p e r d r i v e n * * * ...
Page 40 - I s e j e c t e d
DRM-7000 Operating Instructions The slot must be empty in order to use this command. It the slot contains a disc or is unknown to hold a disc when the Enter button is pressed, the message on the LCD display remains unchanged. If the specified slot is empty, the mail slot tray opens and the following...
Page 43 - Components; Drives; connections when installing into the Changer.
DRM-7000 Operating Instructions 6.0 Optional/Additional Components 6.1 Adding Drives Any drive designed for use in the DRM-7000 may be easily added to this system. The power supply shipped with the unit is capable of supporting up to eight additional components. Install the devices in to the lower r...
Page 44 - D r i v e 1; D r i v e 2
DRM-7000 Operating Instructions 2. Connect the power cord from the Changer to the drive. • Verify that the wiring monitor indicator on the rear of the drive lights as orange • Check that the termination indicator is green if the Termination Switch is ON 3. Connect the Changer Interface cable to the ...
Page 47 - M a g a z i n e – b a y o r; S e t u p b r o w s e r; Escape; R e v i s i o n; Escape; I n i t i a l i z i n g
DRM-7000 Operating Instructions M a g a z i n e – b a y o r R e a r ( d r i v e ) – b a y ? Press the Escape button ( C o n f i g ) S e t u p b r o w s e r Press the Escape button ( I n q u i r y ) I D = 5 R e v i s i o n * . * * * Press the Escape button F r o n t - d o o r : C l o s e R e a r - d ...
Page 50 - Problem Description; Remove the discs and restart
DRM-7000 Operating Instructions 7.0 Troubleshooting Often setup mistakes and simple errors are misinterpreted as hardware failures. The following chart provides solutions to common errors or problems. If the error remains after taking the appropriate steps, repeat the actions. If it continues to fai...
