Pioneer DRM-7000 - Manuals

DRM-7000 Operating Instructions benzine, thinner, insecticide or other strong chemicals as these may dissolve or discolor the cabinet surface. Some commercially produced chemical polishing clothes may be acceptable but read all instructions and warnings first. 2.5 Managing Offline Media The DRM-7000...

DRM-7000 Operating Instructions • Two drives installed on separate cables • Both drives are connected to the internal daisy-chain board using the cables provided (it is necessary to purchase another SCSI cable to connect the Changer to the HOST) To install three or more drives or to use more than on...

DRM-7000 Operating Instructions • 20-Disc Hyper Magazine Dust Cover • Operating Instructions • Warranty Information • Service Network Sheet 2.8 Add-On Products The following components may be purchased separately for use with the Pioneer DRM-7000 Changer. • 50-Disc Locking Magazine (DRM-AL751) This ...

DRM-7000 Operating Instructions 3.0 Names and Functions of Individual Parts - 8 -

DRM-7000 Operating Instructions 4.0 Installation 4.1 Positioning the Changer The instructions below lead through the physical installation of the DRM-7000. 1. Attach the placement fixtures To stabilize the Changer further, attach the placement fixtures at the corners of the unit • Always be sure to ...

DRM-7000 Operating Instructions 3. Lock all four legs/wheels into place 4. Connect the power cord to the Changer • Insert the power cord into the rear of the changer before inserting the plug into the wall socket Caution: Always be sure to use only a power cord designed for use in that country. 4.2 ...

DRM-7000 Operating Instructions 2. Loosen the shipping screws With the front access panel open, loosen the two screws located in the base • Screws are permanent to avoid becoming lost but must be loosened to operate the Changer • Tighten these screws before moving or transporting the Changer • Closi...

DRM-7000 Operating Instructions 5. Connect the Changer Interface cable to the drive. • Confirm that the interface cable is connected to the correct bay Caution: Connecting the interface cable to an incorrect bay port results in damage to the discs. • Install an add-on connector board if necessary 4....

DRM-7000 Operating Instructions SCSI buses allows duplicate SCSI IDs as long as the duplicates are assigned to separate buses. Even if none of the drives installed within the changer has been assigned the same SCSI ID, it is necessary to assign a different SCSI ID to any drives which share the same ...

DRM-7000 Operating Instructions Daisy-chain six internal readers and a recorder then connect the Changer – requires a cable for four drives Connect two readers and two recorders then connect the Changer – requires three separate SCSI controller cards 4.6 Inserting Disc Magazines Please review the in...

DRM-7000 Operating Instructions 5. Remove the magazine by flipping the handle out and pulling the unit towards you. Support the magazine so that it remains level as it slides off of the rails. 4.6.2 Inserting Discs Using a 20-Disc Hyper-Magazine Follow the directions below to insert discs in to a hy...

DRM-7000 Operating Instructions A similar message appears when a magazine is removed from the Changer. M1 Locked – type out If these messages appear repeatedly in rapid succession, the magazine is improperly inserted into the bay. Remove the magazine and remount the unit into the appropriate Changer...

DRM-7000 Operating Instructions Once the initialization is complete, the following message appears in the LCD display: Robotics readyDrive1 no disc The first line of the message refers to the status of the disc changer mechanism. The second line indicates the disc number and registers any loaded dis...

DRM-7000 Operating Instructions 5.0 Operation The DRM-7000 supports two modes, User and System Administrator. Separating the operations into two modes prevents interference, conflicts, or clashes from occurring between commands issued from the host computer and commands entered at the Changer’s Cont...

DRM-7000 Operating Instructions Information submodes enable a System Administrator to check a Changer’s current settings or read the stored data. The System Administrator may also view a variety of Changer information without interfering with the control of the Changer from the host computer. Operat...

DRM-7000 Operating Instructions To change the selected bay, use the up and down arrow buttons. Example: arrow button Bay # 5 & # 6 flip unit arrow button Bay # 9 no component arrow button Bay # 15 & # 16 ID = ************ If the bay holds a drive, press Enter to display the SCSI ID, the term...

DRM-7000 Operating Instructions If the locking record log is empty, the following message appears: Locked – state When there are records in the memory, the following message appears: Uncertain – state Example of Magazine Bay selection: Press the up arrow button while the hyper magazine information d...

DRM-7000 Operating Instructions The optional operations are as follows when scanning using the right arrow button: • Auto Probing – default set to OFF at time of shipment • Inquiry Change – default set to OFF at time of shipment • Free Message – default set to Off at time of shipment • Alert Buzzer ...

DRM-7000 Operating Instructions # 1 2 3 , # 2 2 1 , # 2 5 8 , M 1 5 ( # 7 0 1 - # 7 5 0 ) , Press the Up arrow button H y p e r ( # 7 5 1 - # 7 7 0 ) ,e n d o f l i s t 5.2.4.2 Contents Request a Content log to review the number of filled and vacant slots within the combined magazines. F u l l s l o...

DRM-7000 Operating Instructions Select Drive Work Time to reveal the total time each drive has been in opration. P o w e r O n - t i m e o r D r i v e w o r k - t i m e ? Press the Enter button D r i v e 1 w o r k s * * * * * * h o u r s * * m i n Press the Up arrow button D r i v e 2 w o r k s * * ...

DRM-7000 Operating Instructions E l e v a t i o n d o n e * * * * * * t i m e s Press Down or Up arrow button L o a d / U n l o a d d o n e * * * * * * t i m e s Press Down or Up arrow button M a i l s l o t d r i v e n * * * * * * t i m e s Press Down or Up arrow button H y p e r d r i v e n * * * ...

DRM-7000 Operating Instructions The slot must be empty in order to use this command. It the slot contains a disc or is unknown to hold a disc when the Enter button is pressed, the message on the LCD display remains unchanged. If the specified slot is empty, the mail slot tray opens and the following...

DRM-7000 Operating Instructions 6.0 Optional/Additional Components 6.1 Adding Drives Any drive designed for use in the DRM-7000 may be easily added to this system. The power supply shipped with the unit is capable of supporting up to eight additional components. Install the devices in to the lower r...

DRM-7000 Operating Instructions 2. Connect the power cord from the Changer to the drive. • Verify that the wiring monitor indicator on the rear of the drive lights as orange • Check that the termination indicator is green if the Termination Switch is ON 3. Connect the Changer Interface cable to the ...

DRM-7000 Operating Instructions M a g a z i n e – b a y o r R e a r ( d r i v e ) – b a y ? Press the Escape button ( C o n f i g ) S e t u p b r o w s e r Press the Escape button ( I n q u i r y ) I D = 5 R e v i s i o n * . * * * Press the Escape button F r o n t - d o o r : C l o s e R e a r - d ...

DRM-7000 Operating Instructions 7.0 Troubleshooting Often setup mistakes and simple errors are misinterpreted as hardware failures. The following chart provides solutions to common errors or problems. If the error remains after taking the appropriate steps, repeat the actions. If it continues to fai...