Page 4 - Important Safety Instructions; receptacles, and the points where they exit from the apparatus.
4 C2604M (7/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manu...
Page 5 - The product and/or manual may bear the following marks:; RISK OF ELECTRIC SHOCK.
C2604M (7/06) 5 The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying...
Page 6 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE; This Class A digital apparatus complies with Canadian ICES-003.
6 C2604M (7/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired ...
Page 7 - Product Overview; DESCRIPTION; Multimode fiber support for distances up to 6 km
C2604M (7/06) 7 Product Overview DESCRIPTION The FT85011A/FR85011A fiber transmitter and receiver provide the ability to transmit one unidirectional composite video channel and one bidirectional data channel over one optical fi ber. In addition, patent-pending technology provides the solution for al...
Page 9 - MODELS; OPTIONAL ACCESSORIES
C2604M (7/06) 9 MODELS The FT85011A/FR85011A fiber transmitter and receiver consist of the following series of models : Multimode Models:* FT85011AMSTR Single-channel fiber optic video transmitter/data transceiver; multimode, ST connector FR85011AMSTR Single-channel fiber optic video receiver/data t...
Page 10 - FRONT PANEL; Troubleshooting
10 C2604M (7/06) FRONT PANEL The front panel of the FT85011A transmitter and the FR85011A receiver provides LED indicators that allow you to monitor data activity, signal status, laser status, and operating power (refer to Figure 2). Figure 2. Front Panel of FT85011A Transmitter and FR85011A Receive...
Page 11 - REAR PANEL; Installation
C2604M (7/06) 11 REAR PANEL All connections to the FT85011A transmitter and the FR85011A receiver are made to the rear panel of the modules (refer to Figure 3). Figure 3. Rear Panel of FT85011A Transmitter and FR85011A Receive r For additional information about rear-panel connections and about the D...
Page 12 - PACKAGE CONTENTS; The following items are supplied:; DATA COMMUNICATION SETUP; Data Selection Switch
12 C2604M (7/06) Installation PACKAGE CONTENTS The following items are supplied: 1 FT85011A transmitter or FR85011A receiver 1 Regulated switching power supply with four plug adapters (North American, Australian, U.K., and European configurations); 100-240 VAC, 50-60 Hz input, 12 VDC output 1 Wall c...
Page 13 - Data Communication Switch Settings; Data Communication; Coaxitron
C2604M (7/06) 13 With the FT85011A transmitter/FR85011A receiver powered off, set the Data Selection switch to the required data communication using a small screwdriver. Refer to Table A for data communication switch settings. Table A. Data Communication Switch Settings Note the following: • The FT8...
Page 14 - MOUNTING; before; MOUNTING THE TRANSMITTER/RECEIVER INTO A RACK; Designed to accommodate fiber optic modules as follows:; MOUNTING THE TRANSMITTER/RECEIVER TO A WALL; Mounting the Transmitter/Receiver Using the Wall Clip
14 C2604M (7/06) MOUNTING The FT85011A transmitter/FR85011A receiver can be mounted into a rack or can be used as a stan d-alone module. As a stand-alone module, the unit can be placed on a desktop or can be mounted to a wall. NOTE: As a matter of convenience, it is recommended that you set the desi...
Page 15 - two holes on the lower flange of the clip.
C2604M (7/06) 15 Mounting the Transmitter/Receiver Using the Wall Clip NOTE: Before mounting the FT85011A transmitter/FR85011A receiver to a wall, ensure that there is adequate space at both ends for viewing the front-panel LEDs and for m aking the various rear-panel cable connections. To attach the...
Page 16 - CONNECTIONS; Power connection
16 C2604M (7/06) CONNECTIONS Connections to the FT85011A transmitter and the FR85011A receiver are made on the rear panel of the modules and consist of the following: • Power connection NOTES: – A 12 VDC or 24 VAC power supply can be used to power the transmitter/receiver when used as a stand-alone ...
Page 17 - Data Connector Pin Assignments; Pin; Ground
C2604M (7/06) 17 Table B. Data Connector Pin Assignments Pin Number RS-232 RS-422 RS-485 2-Wire RS-485 4-Wire Manchester Bi-Phase 1 — TX+ (Out+) T+/R+ (Out+/In+) TX+ (Out+) — — 2 — TX- (Out-) T-/R- (Out-/In-) TX- (Out-) — — 3 — RX+ (In+) — RX+ (In+) RX+ (In+) (W) RX+ (In+) 4 — RX- (In-) — RX- (In-) ...
Page 18 - RS-232 Data Communication Wiring
18 C2604M (7/06) Figure 7. RS-232 Data Communication Wiring RS-232 DATA SELECTION RS-232 DATA CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER FR85011A RECEIVER – DATA CONNECTOR 12345 RX (DATA IN) (DATA OUT) 6 TX RX (DATA IN) (DATA OUT) TX 78GND DEVICE A FT85011A TRANSMITTER – DATA CONNECTOR RS-23...
Page 19 - RS-422 Data Communication Wiring
C2604M (7/06) 19 Figure 8. RS-422 Data Communication Wiring RS-422 DATA SELECTION RS-422 DATA CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER 1 TX+ (DATA OUT+) (DATA OUT-) (DATA IN+)(DATA IN-) (DATA OUT+) (DATA OUT-) (DATA IN+)(DATA IN-) 2 TX- 3 RX+ 4 RX- 5678GND RX+ RX- TX+ TX- FT85011A TRANSMIT...
Page 22 - Manchester Data Communication Wiring
22 C2604M (7/06) Figure 11. Manchester Data Communication Wiring MANCHESTER MANCHESTER DATA SELECTION MANCHESTER DATA CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER FR85011A RECEIVER – DATA CONNECTOR 123 RX+ (DATA IN+) 4 RX- (DATA IN -) 5678GND W* B* DEVICE A MANCHESTER DATA CONNECTIONS BETWEEN ...
Page 23 - Bi-Phase Data Communication Wiring
C2604M (7/06) 23 Figure 12. Bi-Phase Data Communication Wiring BI-PHASE DATA CONNECTIONS BETWEEN DEVICE A AND FR85011A RECEIVER BI-PHASE DATA CONNECTIONS BETWEEN DEVICE B AND FT85011A TRANSMITTER FT TRANSMITTER – DATA CONNECTOR 85011A DEVICE B BI-PHASE DATA SELECTION 1234567 TX+ AT (D A OUT+) 8 TX- ...
Page 24 - Troubleshooting with Front-Panel Indicators; Indicator Color; Optic Fault LED
24 C2604M (7/06) Troubleshooting LED indicators on the front panel of the FT85011A transmitter/FR85011A receiver (refer to Figure 2) allow you to monitor signal status, laser status, data activity, and operating power. Table C provides information about the front-panel indicators and associated trou...
Page 25 - Green
C2604M (7/06) 25 Optic Fault LED Green The optical signal is being received and laser is operating properly. — No action required. Red The optical signal is not being received. Remote fiber module is not powered on. Check power connections. Replace power supply if necessary. Fiber optic cable is not...
Page 27 - Specifications; VIDEO
C2604M (7/06) 27 Specifications VIDEO Number of Channels 1 Modulation Type Pulse code modulation, 8-bit resolution Video Input (FT85011A)/ 1.0 Vp-p, 75 ohms; NTSC, PAL, and SECAM Video Output (FR85011A) Bandwidth 6.5 MHz Gain Unity Differential Gain <2% Differential Phase <1° Tilt <1% Signa...
Page 31 - PRODUCT WARRANTY AND RETURN INFORMATION; REVISION HISTORY
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic ...
