Page 3 - CONTENTS; Section
C309M-J (9/04) 3 CONTENTS Section Page IMPORTANT SAFETY INSTRUCTIONS ............................................................................................................................................................................... 5 OPERATION ..............................................
Page 5 - IMPORTANT SAFETY INSTRUCTIONS; RISK OF ELECTRIC SHOCK.
C309M-J (9/04) 5 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such ...
Page 6 - OPERATION; HOW TO OPERATE YOUR SYSTEM
6 C309M-J (9/04) OPERATION POWER-UP DISPLAY When the system is powered up, the selected protocol, revision number, and other information is displayed on the monitor. For example,the screen might show the following information: The information displayed depends on the selected protocol (C, D, or P) a...
Page 7 - OPERATING NOTES; ENVIRONMENTAL RANGE; Controller; SCAN SPEED
C309M-J (9/04) 7 OPERATING NOTES ENVIRONMENTAL RANGE The operating temperature ranges from a minimum of -50 ° F (-45 ° C) to a maximum of 122 ° F (50 ° C) for sustained system operation or 140 ° F (60 ° C) absolute maximum. The entire unit can de-ice and be operational in two hours from a temperatur...
Page 8 - Park Time Minutes section), the system goes to; AUTO IRIS; To operate the wiper do the following:; OPEN COLLECTOR AUXILIARY OUTPUT
8 C309M-J (9/04) PATTERNS The Esprit system can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This patterncan consist of any standard pan and tilt or lens command. Presets, flip, digital zoom, proportional pan, and turbo are not allowed in...
Page 12 - PROGRAMMING; if this is your first time entering this mode
12 C309M-J (9/04) PROGRAMMING ACCESSING MAIN MENU (PRESET 95) You can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions f...
Page 13 - AUTO FOCUS MODE; There are two auto focus modes:
C309M-J (9/04) 13 AUTO FOCUS MODE There are two auto focus modes: Auto – If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place the focus in the manual mode. The system will return to auto focus if you pan or tilt the unit or do a zoom function. Off – If the mode i...
Page 14 - The following are the settings for auto iris:
14 C309M-J (9/04) AUTO IRIS The following are the settings for auto iris: ModeLevelPeak To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Position the cursor ...
Page 16 - AUTO SHARPNESS; The following settings are available for auto sharpness:
16 C309M-J (9/04) AUTO SHARPNESS The following settings are available for auto sharpness: On – Automatically sets the sharpness of the camera.Off – The sharpness of the camera needs to be manually set (refer to Sharpness). To change the mode: 1. Program preset 95 (28). The main menu appears. 2. Posi...
Page 19 - AZIMUTH ZERO
C309M-J (9/04) 19 AZIMUTH ZERO Azimuth is the pan angle from 0 ° to 359 ° . Azimuth zero is the programmed 0 ° point that is normally set to magnetic north. Once programmed, on-screen pan position (azimuth) and compass readings are based on the set azimuth zero point. To set azimuth zero: 1. Program...
Page 20 - BACKLIGHT COMPENSATION; in normal lighting
20 C309M-J (9/04) BACKLIGHT COMPENSATION There are two backlight compensation modes: On – The system uses the center 10 percent of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in ...
Page 21 - DIRECTION
C309M-J (9/04) 21 DIRECTION Direction programs the horizontal display position of the Direction label (N, NW, NE, …). NOTE: For direction to be accurate, the azimuth zero must be set to magnetic north. NOTE: Direction display is not available while you are programmming or running a pattern. The foll...
Page 22 - DIRECTION LINE; To program the vertical label position for Direction:
22 C309M-J (9/04) DIRECTION LINE Direction Line controls the vertical display position of the Direction label. The label may be displayed on lines 3 through 10. Line 3 is thethird line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. NOTE...
Page 23 - DISPLAY DURATION; Press the Iris Open button to enter the Other menu.
C309M-J (9/04) 23 DISPLAY DURATION Display Duration programs the duration the Az/El, Direction, and Zoom labels are displayed on the monitor. The available settings fordisplay duration include the following: CONSTANT - The label is displayed continuously.2 SECONDS (default) - The label is displayed ...
Page 24 - GAIN LIMIT; Press the Iris Open button to enter the Camera menu.
24 C309M-J (9/04) GAIN LIMIT The gain limit sets the maximum level for the automatic gain control. Increasing the level will increase the signal level and increase thenoise level of the picture. To change the gain: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) besid...
Page 26 - LIMIT STOPS; TURNING LIMIT STOPS ON OR OFF
26 C309M-J (9/04) LIMIT STOPS NOTE: Limit stops are inactive while setting items in the program menu (e.g. azimuth zero, scan limits, manual pan limits). TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) besid...
Page 27 - LIMIT STOPS MENU; Press the Iris Open button to enter the Limit Stop menu.; CLEAR MANUAL STOPS; To clear the manual limit stops:
C309M-J (9/04) 27 LIMIT STOPS MENU The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu. 4. Move the cursor to ...
Page 28 - Scan Limit Stops
28 C309M-J (9/04) Scan Limit Stops When scan limit stops are set, the pan and tilt reverses direction during random, frame, or auto scanning when a limit stop is reached.The manual scan limit stops can be set in one of two ways: At the controller by programming presets 92 and 93 or At the controller...
Page 29 - LINE SYNCHRONIZATION; There are two settings for line synchronization:
C309M-J (9/04) 29 LINE SYNCHRONIZATION If cameras are out of phase with each other, they may produce what appears to be vertical roll when switching between cameras. There are two settings for line synchronization: On – Adjust the synchronization of the power line voltage so that it is in phase with...
Page 31 - PARK TIME MINUTES; Preset 1 must be programmed for the dome to park.
C309M-J (9/04) 31 PARK TIME MINUTES This feature causes the system to park at preset 1 after a programmed number of minutes of control inactivity. The time can be set from 1minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature. NOTE: Preset 1 must be programmed for ...
Page 32 - PATTERN LENGTH; The Esprit can do the following:
32 C309M-J (9/04) PATTERN LENGTH The Esprit can do the following: One full pattern - 1.5, 3, or 6 minutes long or Two half patterns - .75, 1.5, or 3 minutes long This pattern can consist of any standard pan, tilt, or lens command. Presets, flip, and turbo are not allowed in a pattern. Zone scan can ...
Page 34 - PROPORTIONAL PAN; There are two proportional pan modes:
34 C309M-J (9/04) PROPORTIONAL PAN There are two proportional pan modes: On – Enables the proportional pan mode. The amount of zoom controls the pan and tilt. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings. This...
Page 35 - RESET CAMERA; Default Setting; AGC mode; Auto
C309M-J (9/04) 35 RESET CAMERA Default Setting <Camera><Line Sync><Power Up><Wiper><Limit Stop><Other>Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera<Gain/AGC><Auto iris>NextExit Camera Menu Resetting the camera returns the settings to t...
Page 36 - To change the scan speed:
36 C309M-J (9/04) SCAN SPEED The scan speed is adjustable from 1-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan. To change the scan speed: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other. 3. Press the Iris Open button...
Page 37 - SHARPNESS; To manually set the sharpness of the camera:
C309M-J (9/04) 37 SHARPNESS Use the Sharpness setting to manually set the sharpness of the camera. To manually set the sharpness of the camera: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Po...
Page 38 - SHUTTER SPEED
38 C309M-J (9/04) SHUTTER SPEED There are several electronic shutter speed settings: Auto1/21/41/81/151/301/601/1201/1801/2501/5001/10001/20001/40001/10,0001/30,000 In the Auto setting the camera controls the shutter speed automatically. Increasing the shutter speed lowers the light sensitivity, but...
Page 39 - SPEED PROFILE; To set the speed profile:
C309M-J (9/04) 39 SPEED PROFILE This feature allows the operator to set the wind speed conditions for the location of the Esprit system. You can set two wind speedprofiles of 50 mph or 90 mph in which the system will remain operational. In both settings, the pan speed will be a maximum of 40degrees ...
Page 40 - WHITE BALANCE
40 C309M-J (9/04) WHITE BALANCE The settings for white balance are as follows: Auto white balR GainB Gain To change the white balance settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Po...
Page 41 - WIPER MODE
C309M-J (9/04) 41 WIPER MODE There are three wiper settings: Wiper ModeWiper DwellWiper Time To change the wiper settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Wiper. 3. Press the Iris Open button to enter the Wiper menu. 4. Move the joystick up or d...
Page 43 - ZOOM; To program the horizontal label position for Zoom:
C309M-J (9/04) 43 ZOOM Zoom programs the horizontal display position of the Zoom label. The following settings are available for the Zoom label: Off – Label is not displayed.Left – Label is displayed on the left-hand side of the screen.Center (default) – Label is displayed in the center of the scree...
Page 44 - ZOOM LIMIT; To change the zoom limit:
44 C309M-J (9/04) ZOOM LIMIT ES30C16/ES31C16 - 16X optical zoom and 10X electronic zoom, can be set for 16X, 32X, 64X, 128X, or 160X.ES30C22/ES31C22 - 22X optical zoom and 10X electronic zoom, can be set for 22X, 32X, 88X, 176X, or 220X.ES30CBW18/ES31CBW18 - 23X optical zoom and 10X electronic zoom,...
Page 45 - ZOOM LINE; To program the vertical label position for Zoom:
C309M-J (9/04) 45 ZOOM LINE Zoom Line controls the vertical display position of the Zoom label. The label may be displayed on lines 3 through 10. Line 3 is the third linefrom the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. NOTE: Zoom display ...
Page 46 - SPECIFICATIONS; ELECTRICAL
46 C309M-J (9/04) SPECIFICATIONS ELECTRICAL Input Voltage: 24, 120, or 230 VAC, 50/60 Hz; switch selectable for 120/230 VAC inputs. Reset feature enabledwhen power becomes unstable or interrupted. Power Requirements: Maximum power consumption is 70 VA per system Heater and Defroster: Thermostaticall...
Page 49 - REGULATORY NOTICES; WARRANTY AND RETURN INFORMATION
REVISION HISTORY Manual # Date Comments C309M 9/00 Original version. C309M-A 12/00 Added information on “Pan Limit” message per ECO #00-6635. C309M-B 6/01 Added information on zone blanking. C309M-C 9/02 Camera modifications. C309M-D 6/03 Added Az/El/Direction menu per ECO #03-8861. Updated layout. ...
