Page 3 - Contents
C2688M-C (12/08) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . ....
Page 5 - Regulatory Notices; REGULATORY NOTICES; Reorient or relocate the receiving antenna.
C2688M-C (12/08) 5 Regulatory Notices REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference tha...
Page 6 - Description; COMPATIBLE PRODUCTS; Endura recording system:
6 C2688M-C (12/08) Description The EDI5000 Endura ® data interface provides a flexible integration platform between third-party systems and the Endura IP video surveillance platform. The EDI5000-AD2088 provides an interface to the American Dynamics ™ AD2088 keyboard, allowing security personnel to i...
Page 7 - IMPORTANT NOTE. PLEASE READ; Sample System Using Endura to Record Matrix Video
C2688M-C (12/08) 7 IMPORTANT NOTE. PLEASE READ The network implementations are shown as general representations only and are not intended to show detailed network topologies. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the systems as illu...
Page 8 - FRONT AND REAR PANELS; Front Panel Indicators
8 C2688M-C (12/08) FRONT AND REAR PANELS Figure 3 illustrates the front and rear panels of the data interface (refer to Front Panel Indicators on page 33 for a description of the front panel LEDs; refer to Basic Hardware Connections on page 14 for a description of the rear panel connectors). Figure ...
Page 9 - Installation; HARDWARE INSTALLATION OVERVIEW; Software; BEFORE YOU BEGIN; Power Connection; Qty Description
C2688M-C (12/08) 9 Installation HARDWARE INSTALLATION OVERVIEW The following steps provide an overview of how to install the data interface: 1. Install all components of the matrix switching system (refer to the matrix system documentation for instructions). 2. Install the EDI5000 data interface, an...
Page 10 - PRODUCT SERIAL NUMBER LABEL PLACEMENT; To use the serial number label, complete the following steps:; MOUNTING; Desktop installation:; requires the installation of a separate power supply.; Rack mount installation:; DESKTOP INSTALLATION; Power supply refer to; M o d e l
10 C2688M-C (12/08) USER-SUPPLIED PARTS In addition to the standard tools and cables required for a video security installation, you need to provide the following items: PRODUCT SERIAL NUMBER LABEL PLACEMENT The product serial number label helps identify your data interface and its factory configura...
Page 11 - EDI5000 Data Interface Desktop Placement; WALL MOUNT INSTALLATION
C2688M-C (12/08) 11 Figure 5. EDI5000 Data Interface Desktop Placement WALL MOUNT INSTALLATION The data interface can be mounted to a wall using the optional WM5001-4U wall mount system. You can mount up to four data interface units, in any combination, in a fully expanded WM5001-4U (one WM5001-4U w...
Page 12 - Tighten the Thumbscrew to Secure the Unit; RACK MOUNT INSTALLATION; Insert the data interface into the desired slot.
12 C2688M-C (12/08) 3. Tighten the thumbscrew on the wall mount to secure the unit (refer to Figure 7). Figure 7. Tighten the Thumbscrew to Secure the Unit RACK MOUNT INSTALLATION You can mount the EDI5000 in the optional RK5100PS-5U rack mount kit along with additional Endura devices that are compa...
Page 13 - Tighten Thumbscrew to Secure the Unit; PELCO BADGE ORIENTATION; To rotate the Pelco badge:
C2688M-C (12/08) 13 3. Tighten the thumbscrew on the rack mount to secure the unit into the rack (refer to Figure 9). Figure 9. Tighten Thumbscrew to Secure the Unit PELCO BADGE ORIENTATION The Pelco badge on the front panel of the data interface can be rotated in quarter turns. If you install the u...
Page 14 - BASIC HARDWARE CONNECTIONS; CONNECTING THE MATRIX SYSTEM TO THE EDI5000; Wiring the Terminal Block
14 C2688M-C (12/08) BASIC HARDWARE CONNECTIONS CONNECTING THE MATRIX SYSTEM TO THE EDI5000 Figure 11 shows how to wire the terminal block and connect it to the data interface. Note that the terminal block can be attached to the data interface only in the proper position. Figure 11. Wiring the Termin...
Page 15 - Pin Assignment; Ground
C2688M-C (12/08) 15 5. Connect the wires at the other end to the wall block that is provided with the AD2088 keyboard. Figure 12. Connecting the EDI5000 to the AD2088 Keyboard IMPORTANT NOTE: PLEASE READ. The network implementation is shown as a general representation only and is not intended to sho...
Page 16 - NETWORK CONNECTION; Connecting the EDI5000 to the Endura Network; POWER CONNECTION; To connect power, complete the following steps:; NETWORK
16 C2688M-C (12/08) NETWORK CONNECTION NOTE: Consult your network administrator before installing the data interface to avoid possible network conflicts. Use the network port on the front panel and a Cat5e (or better) cable with RJ-45 connectors to connect the data interface to your system network. ...
Page 17 - Power Supply Options; BONJOUR TECHNOLOGY; Install Bonjour for Windows; bonjourforwindows.html
C2688M-C (12/08) 17 Power Supply Options The EDI5000 offers a single 4-pin power connector on the rear panel. The RK5100PS-5U rack mount kit and the NET5301PS power supply attach to this connector. When using a different power supply, attach power to the enclosed 4-pin to 2-pin adapter and attach th...
Page 18 - Bonjour Setup Screen; Use Bonjour to Navigate to the EDI5000 Web Interface; Bonjour Menu Icon
18 C2688M-C (12/08) 5. When prompted with installation options, make sure to uncheck both check boxes. Figure 16. Bonjour Setup Screen When the installation is finished, Bonjour Service will be installed on the PC. If problems with the discovery ever arise, this service should be the first step in s...
Page 20 - Software Configuration; SOFTWARE CONFIGURATION OVERVIEW; Change Configuration; Endura expansion system:; OPTIONAL CONFIGURATION TASKS; Change Configuration Settings; Endura permissions and roles:; description of the Script Offset setting in
20 C2688M-C (12/08) Software Configuration SOFTWARE CONFIGURATION OVERVIEW Once the hardware is installed and all devices are connected, complete the following software configuration tasks: 1. Configure the data interface settings through the EDI5000 system configuration software. Instructions are p...
Page 21 - CONNECT TO THE SYSTEM CONFIGURATION SOFTWARE; Microsoft Internet Explorer 6.0 or later; admin
C2688M-C (12/08) 21 CONNECT TO THE SYSTEM CONFIGURATION SOFTWARE 1. From the Endura workstation (or from any other computer connected to the Endura network) open a Web browser window. The EDI5000 system configuration software is compatible with the following Web browsers: • Microsoft Internet Explor...
Page 22 - CONFIGURE THE DATA INTERFACE SETTINGS; The EDI5000 System Configuration Software
22 C2688M-C (12/08) CONFIGURE THE DATA INTERFACE SETTINGS 1. The EDI5000 system configuration software opens to the Settings page and Configuration tab. To change any other settings (such as the network settings or NVR settings), click one of the other tabs on the Settings page. To use any other pag...
Page 23 - SAVE CHANGES TO THE EDI5000 CONFIGURATION; Restart during sign out:; EDI5000 Configuration Interface: Sample Confirmation Prompt; CHANGE CONFIGURATION SETTINGS; described in the following sections.
C2688M-C (12/08) 23 SAVE CHANGES TO THE EDI5000 CONFIGURATION When changing settings in the EDI5000 system configuration software, you must save or apply the changes before you leave the page; if you leave the page without saving changes, the configuration settings revert to the previously saved set...
Page 24 - Change Serial Port Settings; EDI5000 Serial Port Settings; Change General Configuration Settings; EDI5000 Configuration Settings; Setting
24 C2688M-C (12/08) Change Serial Port Settings Use the Configuration page in the EDI5000 system configuration software to configure the serial port connection as shown in Figure 24. Figure 24. EDI5000 Serial Port Settings Change General Configuration Settings Figure 25. EDI5000 Configuration Settin...
Page 25 - Initial Jump Back Seconds:; CONFIGURE NETWORK SETTINGS
C2688M-C (12/08) 25 WS5000 Advanced System Software Operation manual (C1624M) for instructions on configuring alarms in the Endura system. Refer to the matrix system documentation for instructions on configuring matrix alarms. NOTE: Endura system cameras should not be called by alarms configured in ...
Page 26 - Configure the Data Interface Settings; CONFIGURE DVR/NVR SETTINGS; Add a Recorder to the EDI5000 Configuration
26 C2688M-C (12/08) 2. In the Hostname box type an easily recognizable name that identifies the data interface on the network. Short names are recommended. 3. You can change the IP Address, Subnet Mask, or Gateway settings. Do not change the DHCP setting or the DNS Servers information; these setting...
Page 27 - Figure 28), click Add New NVR to view the Create New NVR Entry section.; Edit a DVR/NVR Entry in the EDI5000 Configuration; Editing a DVR/NVR Entry; Delete a DVR/NVR Entry From the EDI5000 Configuration; Click a device in the NVR Friendly Name section.
C2688M-C (12/08) 27 Add a Recorder to the EDI5000 Configuration Use the Create New NVR Entry section to add a recording device entry to the EDI5000 configuration. NOTE: If you are viewing configuration entry information for a recording device that is already in the EDI5000 configuration (as shown in...
Page 28 - CONFIGURE DECODER-MONITOR SETTINGS; About the Decoding Device; In addition, the decoding device must meet the following criteria:; Add a Decoder Monitor to the EDI5000 Configuration; Adding a Decoder-Monitor Entry to the EDI5000 Configuration
28 C2688M-C (12/08) CONFIGURE DECODER-MONITOR SETTINGS Click the Decoder-Monitor Settings tab to open the Decoder-Monitor settings page. Use this page to identify the analog connection between each Endura decoding device and the matrix system. About the Decoding Device The term Decoder-Monitor refer...
Page 29 - Edit a Decoder Monitor Entry in the EDI5000 Configuration; Editing a Decoder-Monitor Entry; Delete a Decoder Monitor Entry From the EDI5000 Configuration; Click a device in the Decoder-Monitor Friendly Name section.; SYNCHRONIZE THE MATRIX SYSTEM WITH THE ENDURA NTP TIME SERVER
C2688M-C (12/08) 29 Edit a Decoder Monitor Entry in the EDI5000 Configuration The Decoder-Monitor Friendly Name section contains a list of Endura decoding devices that have already been added to the EDI5000 configuration. Use the Editing Decoder Monitor Info section to edit these devices (refer to F...
Page 30 - SOFTWARE UPDATE OPTIONS; Click the Software Update link to open the Software Update page.; FILE SUPPORT OPTIONS; The File Support Page; Export configuration settings from server:; Export; Import selected configuration settings:; Import
30 C2688M-C (12/08) SOFTWARE UPDATE OPTIONS The Software Update page allows you to update the EDI5000 system configuration software, as follows: 1. Click the Software Update link to open the Software Update page. 2. Click Browse to locate the update file (specific details, such as the filename [*.pp...
Page 31 - EXPORT CONFIGURATION SETTINGS; Import Configuration Settings
C2688M-C (12/08) 31 EXPORT CONFIGURATION SETTINGS Use this option to save configuration settings from the EDI5000 to an xml file that can be imported to another EDI5000 data interface unit in thesystem (as described in Import Configuration Settings on page 32). 1. Click “Export configuration setting...
Page 32 - IMPORT CONFIGURATION SETTINGS; ADDITIONAL SOFTWARE FEATURES
32 C2688M-C (12/08) IMPORT CONFIGURATION SETTINGS Use this option to import EDI5000 configuration settings from the xml file that is generated by the export option (described in Export Configuration Settings on page 31). 1. Click “Import selected configuration settings” and then click Browse. 2. In ...
Page 33 - Operation; FRONT PANEL INDICATORS; Network Activity Indicator; Reset Button
C2688M-C (12/08) 33 Operation FRONT PANEL INDICATORS Figure 36. EDI5000 Front Panel Network Activity Indicator The network activity indicator flashes green when the data interface is sending or receiving network data. Network Speed Indicator Network status (connection and speed) is indicated by one ...
Page 34 - RESET BUTTON; Reset to factory default settings; VIEWING VIDEO; To view video, complete the following steps:
34 C2688M-C (12/08) RESET BUTTON The reset button is located at the top of the front panel. Using a probe or paper clip, press the reset button to reboot the EDI5000 as follows: • Reboot the EDI5000 : Press and immediately release the reset button to reboot the EDI5000. • Reset to factory default se...
Page 35 - VIEWING AND CONTROLLING VIDEO; Recorded video from an Endura system camera.; PTZ Control; uses the camera offset value (described in
C2688M-C (12/08) 35 Figure 37. Operating the EDI5000 with the AD2088 Keyboard VIEWING AND CONTROLLING VIDEO To view live video from the matrix system, use the matrix system commands and keyboard options (refer to the matrix system documentation). To view recorded video from a matrix system camera or...
Page 36 - Controlling Recorded Video; Using Digital Zoom; Command
36 C2688M-C (12/08) Controlling Recorded Video Figure 38 illustrates the joystick options for controlling recorded video when viewing at normal magnification (refer to Using Digital Zoom on page 38 for instructions on viewing in digital zoom mode). Figure 38. Controlling Recorded Video with the Joys...
Page 37 - Fast Forward Speeds; Playback Speed; Playback Speeds; Action
C2688M-C (12/08) 37 Fast Forward Speeds When you press Far (Fast Forward) or move the joystick to the right, the recorded video plays at 2x speed. Pressing Far again increases the fast forward speed. Table D identifies the fast forward progression (refer to Playback Speed for an explanation of the a...
Page 38 - Rewind Speeds
38 C2688M-C (12/08) Rewind Speeds When you press Near (Rewind) or move the joystick left, the recorded video plays in reverse at 2x speed. Pressing Near again increases the speed at which the video plays in reverse. Figure E identifies the rewind progression (refer to Playback Speed on page 37 for a...
Page 39 - Troubleshooting; Unit firmware version:; Troubleshooting the EDI5000; Problem
C2688M-C (12/08) 39 Troubleshooting LED indicators on the front panel of the EDI5000 allow you to monitor data activity and operating power. Table F provides troubleshooting information relating to the front panel indicators. If the following instructions fail to solve your problem, contact Pelco Pr...
Page 40 - Specifications
40 C2688M-C (12/08) Specifications MODEL EDI5000-AD2088 Interface that allows serial data communication between an American Dynamics matrix system and the Endura video and recording system. Security personnel can use the AD2088 matrix keyboard to view and control video from their existing matrix sys...
Page 41 - STANDARDS/ORGANIZATIONS; Pelco is a member of the MPEG-4 Industry Forum
C2688M-C (12/08) 41 STANDARDS/ORGANIZATIONS • Pelco is a member of the MPEG-4 Industry Forum • Pelco is a member of the Universal Plug and Play (UPnP) Forum • Pelco is a member of the Universal Serial Bus (USB) Implementers Forum • Pelco is a contributor to the International Standards for Organizati...
Page 43 - PRODUCT WARRANTY AND RETURN INFORMATION
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years: – Fiber optic products– TW3000 ...
