Oster XVSA - Manual
Oster XVSA – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – TO ADJUST THICKNESS OF SLICES; The adjusting nut turns with the shaft and adjust-; SHREDDER PLATE
- Page 3 – TO REMOVE ATTACHMENT FROM POWER UNIT; Attach the housing of slicer to the attachment; PUSHER PLATE REMOVAL; Raise the Pusher Plate and slide it out of the slot in the door XVSD.; OPERATION
- Page 4 – MAINTENANCE INSTRUCTIONS; the holes in the housing.; Keep Hands out of Hopper – use a; These plates are sharp and must be
- Page 5 – XVSD Door
- Page 6 – PART NUMBER LISTING; XVSH HOUSING
- Page 7 – Stainless steel Shredder Plate hole sizes (not drawn to scale); SS Grater Plate; For; Hard; Cheese only; Shredder and Grater Plate Hole; Food; Cole Slaw
- Page 8 – LIMITED XVSA/XVGA ATTACHMENT WARRANTY; Improper installation or alteration of equipment.; FOR COMPLETE XVSA, XVGA AND SHREDDER PLATE SALES
1
XVGA
XVSA
XVSH
INSTRUCTIONS FOR OPERATION AND CARE
XVGA GRATER/SHREDDER AND
XVSA SLICER ATTACHMENTS
Our slicer attachments can be used for slicing potatoes (from 1/16" to 5/8" thickness); cut-
ting vegetables for salads and coleslaw; or for slicing fruits and nuts.
An adjustable slicer plate with shaft are included with the XVSA attachment.
These attachments are made up of the following four basic components:
1. XVSH Housing
2. XVSD Front Door or Hopper
3. XVSP Pusher Plate
4. Plate Holder or Adjustable Slicer Plate units
1. Adjustable Slicer Shaft XASP with S/S "S" knife
2. Shredder Plate Holder XPH
XVSD
XVSP
XPH
WARNING
There are sharp rotating knives behind the front door; keep hands out of hopper
and use a feed pusher or stomper to push product into the hopper – do not use
your fingers. Always stop power unit before opening front for changing, cleaning,
or servicing anything on this unit. Only trained and qualified persons 18 years
and older should use these attachments.
Our versatile grater/shredder attachments can be used to grate and shred cheeses, raw vegetables, nuts, breadcrumbs, etc.
depending on the plate selected. Our S/S plates are available with 3/32", 3/16", 1/4", 5/16" or 1/2" size holes and a special
grating plate for breadcrumbs & hard cheeses. A plate holder with shaft and one 3/16" plate are included with the XVGA
attachment.
PLATE HOLDER WITH SHAFT
Shredder plates are available with 3/32", 3/16", 1/4", 5/16" or 1/2" hole sizes. These plates
have keyhole slots for attaching to shouldered studs on the plate hubs.
DOOR OR HOPPER
The front door is a hopper and lever feed design. It hinges onto the back case and is held
closed with an adjustable latch. To remove the front door, lift the latch and swing the door
open while lifting it from the hinge holes.
PUSHER PLATE
The pusher plate has an integrated handle to push the food into the rotating disc or slicer
knife. It has pins at both ends of the top and hinges into the front door. The pusher plate
has a rubber-tipped stop screw (XP1018) under the handle that can be adjusted to prevent
the plate from coming in contact with the plate or blade.
HOUSING OR BACK CASE
The housing or back case mounts into the attachment socket of a mixer, food cutter or
power drive unit and is retained by the pointed thumbscrew that goes through the attach-
ment hole into the indentation on the neck of the machine.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 TO INSTALL SHREDDER OR GRATER DISCS Stop the machine. Orient the plate with the cutting edge away from the shaft assembly. Locate the keyhole slots on the plateand slide the wide part of the slots over the studs on the plate holder. When the plate is flush with the holder, rotate it clock-wise to ...
3 TO REMOVE XASP ADJUSTABLE SLICE PLATE ASSEMBLY FROMHOUSING Open the door all the way and raise the locking pin XP1007 (on top ofrear of housing) and the assembly will be free for removal by pullingoutward. TO REMOVE ATTACHMENT FROM POWER UNIT Loosen thumbscrew on power unit until hub is free for r...
4 5. Close the slicer front door and fasten the latch. 6. Start the machine. Set at a speed to produce the best product (see machine manual) 7. Raise the pusher plate lever. 8. Place the food to be sliced in the hopper and gently press down on the pusher plate lever. Note: Too much pressure crushes ...
