Page 2 - TABLE OF CONTENTS
TABLE OF CONTENTS WARNINGS AND SAFETY INFORMATION 1 GETTING STARTED 3 YOUR BABY MONITOR 5 LCD DISPLAY OF BABY MONITOR 8 BASIC OPERATION 9 MENU SETTINGS 14 TROUBLESHOOTING 19 PRODUCT SPECIFICATIONS 20 GUARANTEE 21
Page 3 - Power requirements; CAUTION; WARNINGS AND SAFETY INFORMATION; IMPORTANT
1 Do not place the cord in a high "wear and tear" location. Never use a frayed or compromised cord. Never use or place your Parent or Baby units in or near moisture or water (e.g. near bath or pool). Immersing in water can cause electric shock and even death. Power requirements In Australia ...
Page 4 - Battery requirements
2 WARNINGS AND SAFETY INFORMATION Battery requirements E a c h p a r e n t u n i t r e q u i r e s t w o r e c h a r g e a b l e N i - M H batteries, size AAA 1.2V 800mAh (HR10/44). • Do not dispose of the batteries in a fi re, as they can explode. • Do not open, unscrew or temper with any of your b...
Page 5 - Pack Contents; GETTING STARTED; Installation; For the Parent Unit; WARNING
3 Thank you for choosing this monitor from Oricom.Your Secure 200 Baby Monitor offers the best Digital Technology. INTERFERENCEFREE FREQUENCY DECT (Digital Enhanced Cordless Telecommunications) is the most widely used worldwide digital cordless technology, offering amazingly clear sound, long range ...
Page 6 - For the Baby Unit
4 GETTING STARTED 5. Press [ ] to turn the Parent Unit on. • Before fi rst use, or if it has been out of use for a long time, the Parent Unit will need to be charged for 15-16 hours. During this time, the Parent Unit will operate from the Charger pod when switched on. Note that the Parent Unit canno...
Page 7 - YOUR BABY MONITOR
5 YOUR BABY MONITOR Baby unit (Sender) 1 Temperature Sensor Picks up the temperature in your baby's room. 2 Battery Cover For non rechargeable batteries (not supplied). 3 Night light key Press to turn On the night light. Press again to turn Off the light. 4 Power On/Off Key Press to turn ON the Baby...
Page 8 - Left view of baby unit
6 YOUR BABY MONITOR Parent unit (Receiver) 12 Battery Cover Rechargeable batteries. 13 Belt Clip14 Volume Up/Down Keys Adjust the volume at which you hear the sounds in your Baby's room, and scroll through the menu during setting. 15 Power On/Off Key Press to turn the parent unit ON. Press and hold ...
Page 9 - Charger Pod
7 YOUR BABY MONITOR 19 Noise level indicators20 Torch key Press and hold to emit a soft beam of light from the top of the Parent Unit. 21 Talk key Press and hold to talk to your baby or partner in the baby's room via the Baby Unit. Charger Pod 22 Charging Light When Parent unit is placed in the Char...
Page 10 - LCD DISPLAY OF BABY MONITOR; Baby Unit
8 LCD DISPLAY OF BABY MONITOR Baby Unit 1. Battery level indicator2. Numbers/Characters indicator3. Temperature indicator4. Lullaby on/off indicator Parent Unit 1. Sensitivity indicator2. Night light indicator3. Battery level indicator4. Numbers/Characters indicator5. Temperature indicator6. Feed ti...
Page 11 - BASIC OPERATION; Monitoring; Adjusting Volume; On the parent unit
9 BASIC OPERATION Once you have set up your Baby Monitor, you will be able to hear the sounds in your baby's room through the Parent Unit. And also see the green and red sensor lights around the top of the Parent Unit rise and fall with the sound levels. Note: If the connection between the Parent an...
Page 12 - Paging; On the baby unit; Lullaby; On the Baby Unit
10 BASIC OPERATION Baby alert! You can set your Parent Unit to give an extra warning "beep" when the noise levels in your baby's room is high and the red lights on the sound sensor are lit. This is particularly useful if the volume of your Parent Unit is turned down and you are just using th...
Page 13 - On the Parent Unit; Clock
11 BASIC OPERATION 2. Press [ ] key to scroll to the different lullabies, or to select [Play all?]. 3. Press [ ] key again to start or stop the lullaby. On the Parent Unit 1. Press [ ] key, then use [ / ] keys to scroll to "Lullaby". Press [ OK ] key. 2. "Play?" is shown on the displ...
Page 14 - Talk to your Baby; Torch; Parent Unit
12 BASIC OPERATION Talk to your Baby You can speak to your baby from the Parent Unit, perhaps to reassure them that you are on your way.Press and hold [ ] key and speak into the front of the Parent Unit. • Please note that you will not be able to hear your baby while you are speaking to them until y...
Page 15 - Charging the Battery
13 BASIC OPERATION Charging the Battery The Parent Unit will work for up to 10 hours with fully charged batteries. If a battery low alert tone is heard and the battery icon on the Parent Unit's display is fl ashing, you should put the parent unit on the Charger Pod to recharge the batteries. You can...
Page 16 - MENU SETTINGS; Night light Setting; Start playing; Sensitivity Setting
14 MENU SETTINGS Note: All Menu settings operations are only available on the Parent unit. During setting, press [ ] key to exit. Night light Setting You can turn on or off the night light on the baby unit via the parent unit.1. Press [ ] key on the parent unit and use [ / ] keys to select "Nigh...
Page 17 - Sound Alert Setting; Set On or Off; Temperature Setting
15 MENU SETTINGS 1. Press [ ] key on the parent unit and use [ / ] keys to select "Sensitivity". The display is shown below: 2. Press [ OK ] key and then use [ / ] keys to select the sensitivity level. There are 5 levels. 3. Press [ OK ] key to confirm and "Saved" is shown on the dis...
Page 18 - Set desired baby room temperature range; Clock Setting
16 MENU SETTINGS Press [ ] key on the parent unit and use [ / ] keys to select "Temperature". The display is shown below: Set desired baby room temperature range 1. Press [ OK ] key, "Set Range" is shown on the display.2. Press [ OK ] key, use [ / ] keys to set the upper and lower te...
Page 19 - Set the time; Feed Time Setting
17 MENU SETTINGS Set the time 2. Press [ OK ] key and "Set time" is shown on the display. Press [ OK ] key. 3. "Year" is shown on the display. Use [ / ] keys to select the correct year. Press [ OK ] key. 4. "Month" is shown on the display. Use [ / ] keys to select the correct...
Page 20 - Set the; Set the interval for following feeds; Set Alarm on or off; Language Setting
18 MENU SETTINGS Set the fi rst or next feed time 1. Press [OK] key, "Set Time" is shown on the display.2. Press [ OK ] key, then follow the procedures in the Set the time of Clock Setting to set the hour and minute. Set the interval for following feeds 1. Press [ OK ] key and use [ / ] keys...
Page 21 - TROUBLESHOOTING
19 TROUBLESHOOTING Problem Possible cause(s) The red power lights do not turn on when you plug in the power. 1. Check if the units are properly connected to the power supply. 2. Check if the power is turned on. If not, Press [ ] to turn on the power. The green Link light on the Parent Unit is fl ash...
Page 22 - PRODUCT SPECIFICATIONS
20 PRODUCT SPECIFICATIONS Feature Speci fi cations Operating Frequency DECT 1.8 GHz Range Up to 300m under optimum conditions. The range is reduced in buildings (up to 50m) as a result of walls, doors etc. Power supply (Baby Unit) Input: 240 V AC 50Hz Output: 6 V DC , 200 mA, Non rechargeable batter...
Page 23 - GUARANTEE; Customer Support
21 GUARANTEE Warranty (Australia) (a) Warranty Oricom International Pty Ltd (Oricom) warrants that the product is free from defects in materials and workmanship for a period of 12 months effective from the date of purchase. This warranty in no way affects your statutory warranty under the Trade Prac...
