Omron V720-HS04 - Manual - manualsarea.com

Page 2 - ii; actually use the product.; Precautions; Read and Understand this Manual

ii About this Manual: Thank you for purchasing our V720-series Electromagnetic Inductive RFID System. The V720-series is a family of products that were developed by fully utilizing our high technology and broad experience. This Users Manual provides various information that will be necessary when us...

Page 3 - iii; Application Considerations

iii Application Considerations < SUITABILITY FOR USE > OMRON shall not be responsible for conformity with any standards, codes, or regulations thatapply to the combination of the products in the customer's application or use of the products. At the customer's request, OMRON will provide...

Page 4 - iv

iv when significant construction changes are made. However, some specifications of the productsmay be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON repres...

Page 5 - Safety Precautions; Ensure to read the information carefully before use.; WARNING; could result in minor or moderate injury, or may result in serious; Caution; Description of Symbols; Prohibition

v Safety Precautions This chapter provides important information for the safe use of this product. Ensure to read the information carefully before use. In the safety precautions below, severity is categorized as either ”WARNING” or “CAUTION”. WARNING Indicates a potentially hazardous situation which...

Page 6 - vi; Never disassemble, repair, or modify the main unit and cables.; Do not allow the cables to be in contact with heaters.; To; Do not drop the device or apply physical shock.

vi 警 WARNING Never disassemble, repair, or modify the main unit and cables. z Do not disassemble, repair, or modify this product. Doing so may result in electric shock, fire, or personal injury. Do not handle the device with wet hands. Do not touch the terminals while the device is connected to the ...

Page 7 - vii; applies to the models other than waterproof types.); Be sure to tighten the devices screws securely.

vii ・ Locations where the Reader/Writer is exposed to dust, corrosive gas, saline, or flammable gas. ・ Locations where the Reader/Writer is exposed to direct heat. ・ Locations subject to condensation due to high humidity. ・ Locations subject to vibration or impact that exceed the limits outl...

Page 8 - viii; undesired operation of this device.; Declarations

viii Precautions This chapter provides important information for international standards and copyright. Ensure to read the information carefully before use. V720-HS04 conforms to the following laws and standards. This conformity is effective only if V720-HS04 is used with the designated Reader/Write...

Page 9 - TABLE OF CONTENTS; ix; of

TABLE OF CONTENTS ix SECTION 1 Characteristics .................................................................1-1 1-1 Features .................................................................................................................... 1-2 SECTION 2 Specifications and Performance ............

Page 11 - Features

1-1 Features 1-1 1-2 1-1 Features The V720–series Electromagnetic Inductive RFID System is ideal for the construction of highly functional, long–distance wireless ID systems for material control and logistics. The V720-HS04 Antenna is used by connecting it to the V720S-BC5D4A Reader/Writer us...

Page 13 - Antenna; Nomenclature; General Specifications

2-1 Antenna 2-1 2-2 2-1 Antenna 2-1-1 Nomenclature • V720-HS04 No Name Description 1 BNC connector Connects the V720S-BC5D4A Reader/Writer to the Antenna connector for sending/receiving and to the exclusive coaxial cable (sold separately). 2 Detection surface Surface for communication with Tag Anten...

Page 14 - Dimensions

2-1 Antenna 2-1 2-3 2-1-3 Dimensions • V720-HS04 Casing material PVC Back board PVC • Mou nt in g h ol e Mou nt in g h ol e Unit: mm

Page 17 - -1 Installation of Antenna; Installation of Antenna; Installation Environment

3-1 Installation of Antenna 3-1 3-2 3-1 Installation of Antenna 3-1-1 Installation Environment Installation Location It is assumed that this product is to be used indoors, or outdoors if there is a roof. Do not install the Antenna in the following locations. • Place exposed to direct sunlight. • The...

Page 18 - Mounting the Antenna

3-1 Installation of Antenna 3-1 3-3 3-1-2 Mounting the Antenna Be sure to attach the provided bracket to the Antenna and mount the Antenna with four M6 screws with spring washers and flat washers as shown below. Spring washer Flat washer • Mounting Dimensional Drawing (Ho le) (Ho le) Influence of pe...

Page 20 - -1 Communications Areas; Communications Areas; Communication Areas; Communication Area

4-1 Communications Areas 4-1 4-2 4-1 Communications Areas The following diagram shows the communication area available when a standard Tag is used at ambient temperature, 25°C. The communication area varies depending on Antenna installation conditions, Tag forming conditions, Tag installation condit...

Page 21 - -2 Influence of Peripheral Metals during Antenna Installation; Influence of Peripheral Metals of Antenna Installation Site; Influence of back metals; Influence of Peripheral Metals

4-2 Influence of Peripheral Metals during Antenna Installation 4-2 4-3 4-2 Influence of Peripheral Metals of Antenna Installation Site Consider the influence of peripheral metals when installing the Antenna. Peripheral metals may greatly lower the communication distance for the Antenna. V720-HS04 to...

Page 22 - -3 Influence of Tag Angle; Influence of Tag Angle; Communications Range vs. Tag Angle

4-3 Influence of Tag Angle 4-3 4-4 4-3 Influence of Tag Angle The maximum communications range between the Antenna and Tag will be available if the face of the Antenna and the face of the Tag are parallel to each other. The communications range will be reduced if the Tag is mounted at an angle. Take...

Page 23 - -4 Effects of Materials on Tags; Effects of Materials on Tags; Effect of Metal Objects; Effect of Resin Objects

4-4 Effects of Materials on Tags 4-4 4-5 4-4 Effects of Materials on Tags Take into consideration the effects of the mounting location when mounting the Tag. Communications range may be reduced if the Tag is near certain objects. The extent to which the distance will decrease depends on the actual m...

Page 24 - -4 Effects of Materials on Tags; Test Setup

4-4 Effects of Materials on Tags 4-4 4-6 Test Setup • Metal Object • Resin Object Metal Tag Antenna Communication distance Distance betweenback metal and Tag Resin Tag Antenna Communication distance Material: Aluminum plate (thickness = 2.0 mm) Dimensions: 240 x 190 mm

Page 25 - Revision History

Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual. SRFM- 002A Revision code The following table outlines the changes made to the manual during each revision. Page numbers refer to the previous version. Revision code Date Revised ...

Omron V720-HS04 - Manual

Table of Contents:

Summary

Other Omron Models