Omron V600-HA- Manual
Omron V600-HA– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Functions; Interface Cable
- Page 3 – Sensor
- Page 4 – System Configuration
- Page 5 – Transmission Range; Combinations with the V600-HS51 Sensor
- Page 6 – Combinations with the V600-HS63 Sensor
- Page 7 – Combinations with the V600-HS67 Sensor; Transmission Time
- Page 8 – Circuit Configuration; Cautions
- Page 9 – Correct Use; OK
- Page 10 – Dimensions; Amplifier
- Page 15 – Terms and Conditions; APPLICATION CONSIDERATIONS; OMRON ELECTRONICS LLC
2
Intelligent Flag I/II
V600-HA
Intelligent Flag I/II
V600-HA
Innovative RFID Electronic Flags to
Replace Mechanical Flag and Kanban
Systems
• Doesn't need a program and can be used like a sensor.
• Advanced line construction at minimal cost.
• Saves space.
• Precise installation not required (Transmission distance:
100 mm max.).
• A verification function provided on multi-functional type.
• Addition of 16-bit models to the series responds to applica-
tions from Kanban to quality control.
• Equipped with a wiring reduction mode and communications
parity check function (16-bit models).
• Both NPN and PNP output available.
• FCC certified.
Ordering Information/Specifications
■
Amplifier
Type
Read-only (8-bit)
Multi-functional (8-bit)
Read-only (16-bit)
Item Model
V600-HAR91
V600-HAR81
V600-HAM91
V600-HAM81
V600-HAR92
Power supply
24 VDC ±10%, ripple (p-p): 10%
Current consumption
130 mA max.
Input
Transistor output or contact output
Short-circuit current: 3 mA (typical) (IN terminal and 0-V short-circuit)
OFF voltage:
15 to 30 VDC
ON voltage:
0 to 5 VDC
Input impedance:
8.2 k
Ω
Applied voltage:
30 VDC max.
Transistor output
OFF voltage:
15 to 30 VDC
Input impedance:
8.2 k
Ω
Short-circuit current:
3 mA (typical) (for 0-V short-circuit of
INHIBIT/TRG)
ON voltage:
0 to 5 VDC
Applied voltage:
30 VDC max.
Output
NPN open collector
output, 20 mA max. at
30 VDC, residual volt-
age: 2 V max.
PNP open collector
output, 20 mA max.
at 30 VDC, residual
voltage: 2 V max.
NPN open collector
output, 20 mA max. at
30 VDC, residual volt-
age: 2 V max.
PNP open collector out-
put, 20 mA max. at 30
VDC, residual voltage: 2 V
max.
NPN open collector output, 20 mA
max. at 30 VDC, residual voltage: 2 V
max.
Diagnostic functions
Checks for CPU errors and transmission errors
Insulation resistance
50 M
Ω
max. (at 500 VDC) between cable terminals and case
Dielectric strength
500 VAC, 50/60 Hz for 1 min between cable terminals and case (leakage current: 1 mA max.)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Omron V600-HA
Summary
Intelligent Flag I/II V600-HA 3 Note: The connector is not waterproof. If there is a possibility that the connector may be exposed to water, keep it inside the control box. Be sureto use the connector together with the separately sold interface cable. ■ Functions V600-HAR91/-HAR81 (Read-only type) R...
4 Intelligent Flag I/II V600-HA ■ Sensor ■ Transmission Distance Specifications Recommended Combinations Note: 1. The specifications take fluctuations in ambient temperature and slight differences between products into account. 2. The read distance and write distance are the same. 3. Sensor Installa...
Intelligent Flag I/II V600-HA 5 System Configuration Programmable Controller, I/O terminal, B7A, CompoBus/S, etc. Sensor Controller V600-A6 R V600-A6 M Interface cable Amplifier Sensor Data Carrier Power supply 24 VDC Power supply 24 VDC Power supply 24 VDC V600-HAR91/HAR81 V600-HAM91/HAM81 V600...
