Page 2 - iii; PREFACE; This manual is for customer engineers.
iii PREFACE This maintenance manual describes how to maintain the Microline 3390/3391 printer in the field. This manual is for customer engineers. For further information, refer to the Users Manual for handling or operating the equipment.
Page 3 - TABLE OF CONTENTS
i TABLE OF CONTENTS 1. CONFIGURATION 1.1 Standard Printer Configuration 1.2 Options 2. THEORY OF OPERATION 2.1 Electrical Operation 2.1.1 Summary 2.1.2 Microprocessor and the Peripheral Circuit 2.1.3 Initialization 2.1.4 Parallel Interface Control 2.1.5 Print Control 2.1.6 SP/LF Motor Control 2.1.7 ...
Page 6 - CONFIGURATION; Standard Printer Configuration; This printer consists of the following assemblies:; Figure 1-1 Configuration
1 – 1 1. CONFIGURATION 1.1. Standard Printer Configuration This printer consists of the following assemblies: Figure 1-1 Configuration Sheet guide assy Platen knob Access coverassy Upper cover Transformer assy Pull-up roller assy Operation panel assy Main frame Driver board Control/Power supply assy
Page 7 - Options; Attachment assy
1 – 2 1.2 Options (1) Cut sheet feeder unit (CSF)(Narrow and wide versions available) (2) Pull-tractor assy Dual-bin CSF Single-bin CSF Attachment assy
Page 9 - THEORY OF OPERATION
Page 10 - THEORY OF OPERATION; Electrical Operation
2 – 1 2. THEORY OF OPERATION 2.1 Electrical Operation The electrical operation of the printer circuit is described in this section. 2.1.1 Summary Fig. 2-1 shows the block diagram of the printer. The control board is made up of the microprocessors, peripheral circuits, drive circuits, sensorsand inte...
Page 17 - Initialization
2 – 8 2.1.3 Initialization This printer is initialized when the power is turned on or when the I-PRIME-N signal is inputfrom the host side via the parallel interface. For the initialize operation, the RST-N signal is first output from the reset circuit to reset theMPUs and LSIs. When resetting ends,...
Page 18 - Parallel Interface Control
2 – 9 2.1.4 Parallel Interface Control The parallel data input from the host to the interfaced LSI is latched to its internal register atthe falling edge of the STROBE-N signal. At the same time, the LSI sets the BUSY signal to the high level to inform the host that thedata is being processed, and o...
Page 19 - Print Control; HEAD DRIVE TIMING CHART
2 – 10 2.1.5 Print Control Print data is transmitted as parallel data (HEAD1~HEAD24) from LSI to print head. LSI generatesprint timing and drive time. Print Data MPU LSI DRIVER HEAD1-N~HEAD24-N Print Data Print Head Control/Power Supply Board A/D bus HEAD1~HEAD24 Driver Board HEAD DRIVE TIMING CHART...
Page 23 - Encoder Disk; • UTILITY MODE
2 – 14 (2) Encoder Disk In the operation of the spacing motor, the PHASE-A and PHASE-B signals are generatedwhen the encoder disk interrupts the photo sensor. The LSI divides these edge pulse signals in accordance with the print pitch, and sendsthe IPT signal to provide dot-on timing and carriage po...
Page 24 - LF Motor Control
2 – 15 (3) LF Motor Control The LF motor driver (MTD2005F) drives the LF motor in two-phase or 1-2 phase bipolar,based on the phase changeover data and the output current data from the LSI. The data from the LSI is processed by a specific register contained in the LF motor driverto measure the overd...
Page 25 - Operation Panel
2 – 16 2.1.7 Operation Panel The clock synchronization OPCLK of LSI is used to input the switch data and output the LEDdata through the operation panel control LSI (IC1: BU5148S). LSI OPTXD OPCLK OPCLR-N OPRXD 77 78 80 OPTD OPCK NPA2 OPRD Command and Data latch LED Driver Switch controller +5V 79 A ...
Page 30 - Mechanical Operation; Figure 2-2 Arrangement of the head pins; The printhead configuration:
2 – 21 2.2 Mechanical Operation 2.2.1 Printhead mechanism and operation (See Figure 2-2.) The printhead is a spring charged 24-pin driving head using a permanent magnet. It is attachedto the carriage, which moves in parallel with the platen. Electrically, this unit is connected tothe control circuit...
Page 31 - C) the control circuit detects a thermistor
2 – 22 (2) Operation of printhead (See Figure 2-3.) (a) When the printhead is idle, the armature is attracted by a permanent magnet andthe spring fixing the armature is compressed. The print wires fixed to each armatureare thus concealed under the wire guide. (b) When a signal for a character to be ...
Page 40 - REAR (Continuous sheet from push tractor)
2 – 31 (1) Cut sheet and continuous sheet switching mechanism (See Figure 2-8.) Three different paper paths can be selected and set by the change lever. (a) TOP (for cut sheet) When the cut sheet is used in the manual mode or fed by the CSF (option), set thechange lever at the position marked TOP. [...
Page 41 - Correlation in Mechanism
2 – 32 (c) BOTTOM (Continuous sheet from bottom feeder) (option) When the change lever is set in the BOTTOM position, the rotation of the platenis transmitted to the drive gear of the bottom tractor feed unit through the idle gearto feed the sheet which has been set in the bottom tractor feed. At th...
Page 49 - REAR; TOP
2 – 40 Figure 2-14 REAR Release cam Platen TOP BOTTOM Change arm Change lever
Page 55 - When using the continouos paper
2 – 46 (2) When using the continouos paper 1) Set the change lever either to the rear side or the bottom side position. (See Figure2-17.) 2) Set a sheet of paper either to the push tractor or the bottom tractor. 3) Press the “FF/LOAD” switch. 4) The LF motor starts its operation to feed the paper up...
Page 56 - Press the “PARK” button on the operation panel.
2 – 47 2.2.8 Paper park function (continuous paper) Continuous sheets which have been inserted can be reversed automatically by using the “PARK”button on the operation panel. 1) Press the “PARK” button on the operation panel. 2) Reverse LF is started and paper is fed in reverse until paper end occur...
Page 58 - Precaution for Parts Replacement; Do not disassemble the printer as long as it is operating normally.
3 – 1 3. ASSEMBLY/DISASSEMBLY This section explains the procedures for removing and installing various assemblies and unitsin the field. Description is mainly limited to the removal procedure; installation should basically be performedin the reverse sequence of the removal procedure. 3.1 Precaution ...
Page 59 - Service Tools; Table 3.1 Service tools
3 – 2 3.2 Service Tools Table 3.1 lists the tools necessary for replacing printed circuit boards and parts of units in thefield. Table 3.1 Service tools 1 No. 1-100 Phillips 1 Screws screwdriver 2.6 mm 2 No. 2-200 Phillips 1 Screws screwdriver 3-5 mm 3 No. 3-100 1 screwdriver 4 Spring hook 1 5 J-YX4...
Page 60 - Disassembly/Reassembly Procedure; Figure 3-1 Printer unit
3 – 3 3.3 Disassembly/Reassembly Procedure This section explains the assembly replacement procedures according to the following disassemblysystem. [Parts Layout] Figure 3-1 Printer unit Upper cover assy Transformer assy Control/Power supply board Printhead Driver board Printer unit Operation panel b...
Page 71 - Note: Small round hole with metal tip on back up roller holder assy; should be facing
3 – 14 3.3.10 Backup Roller Holder Assy (1) Remove the printhead (see 3.3.1). (2) Remove the upper cover (see 3.3.4 (1) – (5)). (3) Remove the gear case Assy (see 3.3.5). (4) Remove the space motor (see 3.3.7). (5) Remove the backup roller spring 2 . Disengage claws (2 places) of roller holder from ...
Page 84 - PERIODIC MAINTENANCE
Page 85 - ADJUSTMENT
4 – 1 4. ADJUSTMENT (1) Be sure to carry out this adjustment with the printer mechanism mounted on the lowercover. (2) Be sure to carry out this adjustment operation on a level and highly rigid work table(flatness: less than 0.039 inch or 1 mm) so as to minimize adjustment error.
Page 93 - FLOWCHARTS
Page 94 - CLEANING AND LUBRICATION; Cleaning; Avoid dust inside the printer mechanism when cleaning.
5 – 1 5. CLEANING AND LUBRICATION 5.1 Cleaning [Cautions] 1. Be sure to turn OFF the AC POWER switch before cleaning. Remove the AC Power cordfrom the printer. 2. Avoid dust inside the printer mechanism when cleaning. 3. If a lubricated part has been cleaned, be sure to apply lubricating oil to that...
Page 96 - Lubrication
5 – 3 5.2 Lubrication This printer is designed to be maintenance free and requires no lubrication during normaloperation. However it is necessary to apply lubricant in case the printer is disassembled,reassembled, cleaned or parts have been changed. (1) Cleaning time Remarks: 1) Turn off the power b...
Page 98 - TROUBLESHOOTING AND REPAIR; Items to Check Before Repair; Check the inspection items specified in the instruction manual.; Troubleshooting Table
6 – 1 6. TROUBLESHOOTING AND REPAIR 6.1 Items to Check Before Repair (1) Check the inspection items specified in the instruction manual. (2) Find out as many details of the trouble as possible from the customer. (3) Inspect in the conditions as close as possible to those at the time the trouble occu...
Page 99 - Lamp Display; Printer mode display
6 – 2 6.3 Lamp Display (1) Printer mode display Table 6.2 Note:BLINK1 : 400ms ON, 400ms OFFBLINK2 : 200ms ON, 200ms OFF— : LED is kept in Current Condition (no change) (2) Fault alram display When the printer detects any of the various alarm states, the information is displayed asshown below on the ...
Page 100 - Fatal Alarm
6 – 3 (3) Fatal Alarm Table 6.3 (1/2) ALARM CATEGORY ALARM LED DISPLAY ALARM 10 12 15 17 20 PROP UTILITY PRESTIGE BOLD REMARKS TROUBLESHOOTING MAIN CONTROL ALARM FIRMWARE DETECTION ALARM SERIAL INTERFACE ALARM MPU internal RAM alarm Program ROM alarm RAM on Control Board alarm CG ROM alarm EEPROM al...
Page 103 - Connection Circuit Check for Printhead and SP/LF Motor; Printhead
6 – 6 6.4 Connection Circuit Check for Printhead and SP/LF Motor (1) Printhead Signal Connector pin number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 FG HD1 HD3 HD9 HO11 COM COM HD17 HD19 HD21 HD22 HD20 HD18 COM COM HD12 HD10 HD4 HD2 TH FG HD5 ...
Page 106 - Troubleshooting flow chart
6 – 9 6.5 Troubleshooting flow chart 1 Power is not supplied. Is the AC cable connected correctly? Yes No Connect the AC cable correctly. Is fuse F1 on the transformer assy/or F1 on the control/power supply board blown? No Yes Replace fuse (with same type and rating). Remedied? No Yes End Does DC + ...
Page 119 - APPENDIX A
Page 120 - APPENDIX A – 1
APPENDIX A – 1 APPENDIX ABIT IMAGE GRAPH IS — DOT DENSITY (No adjacent dots allowed) 1/144 inch Double speedquad density Double speeddouble density Double Single D 1/60 inch DOT D/2 1/120 inch DOT D/2 1/120 inch DOT D/4 1/240 inch DOT D = 1/60 inch
Page 121 - PCB LAYOUT; PCB list
A – 1 A. PCB LAYOUT PCB list (1) Circuit board SRXC (Control/Power Supply) (2) Circuit board SRXD (Driver) (3) Circuit board LEOP (Operation Panel) (1) Control/Power Supply Board (SRXC) (2) Driver Board (SRXD) (3) Operation Panel Board (LEOP) Short Plug Setting Default 1 - 2:2 - 3: 4 Mbit EPROM1 M/2...
Page 122 - APPENDIX B
Page 123 - SPARE PARTS LIST
B – 1 B. SPARE PARTS LIST Quantity per year: Indicates the recommended number of each part that should be ordered forroutine maintenance for one year for 500 units of printers and assuming that the printers areoperated for 2 hours/day of 600 hours/year. The following codes are used to indicate the n...
Page 124 - Figure 11-1 Upper Cover Assy
Page 126 - Figure 11-2 Printer General Assy
B – 4 Figure 11-2 Printer General Assy 1 6 9 8 2 7 4 5 3 11 10
Page 127 - Figure 11-2 Printer General Assy
B – 5 No. Part No. Description Q'ty Q'ty Remarks Required 1 2PP4025-2871P21 Platen Knob 1 1 2 4YA4042-1545G302 Control/Power supply 1 9 Without ROM board (SRXC) 3 4YA4042-1544G1 Driver board (SRXD) 1 9 4 4YA4042-1516G4 Operator panel board 1 3 (LEOP) 5 3PP4044-5360G3 Operation panel 1 2 6 3YS4011-12...
Page 128 - Figure 11-3 Printer Unit
B – 6 Figure 11-3 Printer Unit 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 37 36 9 33 34 35 32 31
Page 131 - Figure 11-4 Carriage Assy
B – 9 Figure 11-4 Carriage Assy 12 9 8 6 14 11 10 1 13 5 4 7-1 7-2 3
Page 132 - Figure 11-4 Carriage Option Assy
B – 10 No. Part No. Description Q'ty Q'ty Remarks Required 1 4PP4044-5061G1 Carriage frame set 1 2 2 3 4PA4025-3718G1 Back up roller holder assy 1 2 4 4PP4025-3398P1 Guide roller 1 2 5 3PP4044-5065P1 Guide roller holder 1 2 6 4YA4044-5120G1 Space motor assy (24) 1 4 7-1 3PB4044-5506P1 Head cable (9N...
Page 133 - Figure 11-5 Option Spare Parts
B – 11 Figure 11-5 Option Spare Parts 1 2 3 4 5 6 7 [Pull-Tractor] [Bottom-Tractor] [I/F Board]
Page 135 - APPENDIX C
Page 137 - OPERATION DESCRIPTION; Element Description; An RS-232C standard line receiver; Circuit Description
C – 2 2. OPERATION DESCRIPTION 2.1 Element Description (1) 80C51 with MASK ROM An eight-bit microprocessor controller that controls the following: (a.) Serial interface protocol and data transfer through a serial port. (b.) Message buffer. (c.) Transmission of parallel data to the printer. (2) SN751...
Page 138 - Driver
C – 3 OCS P1 P2 P0 P3 TD RD IF WR LS245 2764 ROM 8 KB RD TD RAM 8 KB Driver +5 VD 10 VAC +5 V +9 V –9 V +5V 0V ±9 V power supply circuit Serial datacontrol line Bus line Control line ADR latch Receiver DB0 to DB9 ADR/data bus ADR bus 80C51 RST CN1 Figure C-2-1 Block diagram
Page 139 - Operation at power on
C – 4 2.2.1 Operation at power on After power is turned on, an RST OUT signal is sent from the printer control board to reset theprinter. When the reset is canceled, the 80C51 CPU performs initialization. Initialization consistsof setting the 80C51 timer, and setting the serial mode. 2.2.2. RS-232C ...
Page 140 - Communication Procedure Flowchart; Mode a
C – 5 Ready/Busy Received one character? Yes Is DSR valid? No Buffer overflow? Error? Parity error No error Store the received character in buffer. Is the printer in DESELECT state or is the paper low? No No Yes Yes No DSR High? Yes Store 40 H in buffer. Yes Yes No Yes Is remaining buffer space <...
Page 141 - Mode b
C – 6 Figure C-2-3 X-ON, X-OFF Received one character? Yes Is DSR valid? No Buffer overflow? Error? Parity error No error Store the received character in buffer. Is the printer in DESELECT state or is the paper low? No No Yes Yes No DSR High? Yes Store 40 H in buffer. Yes Yes No Yes Is remaining buf...
Page 142 - TROUBLESHOOTING FLOWCHART; Before Repairing a Fault; The data is not received using a serial interface.
C – 7 3. TROUBLESHOOTING FLOWCHART 3.1 Before Repairing a Fault Before servicing the printer, ask the customer in what situation the trouble occurred and recordthe response. Before starting troubleshooting, operate the printer in the same situation as that at the time oftrouble occurrence to see if ...
Page 145 - WR signal is started?
C – 10 Figure C-3-5 542ns 5V 0V 5V 0V WR Q3-3 2 In receiving by serial interface, printing data is omitted or printing operation is not performed. Are RxD and SSD of Q3 as specified in Figure C-3-4? No Replace the Q2. Yes Are, WR, and BUS signals of Q3 pin 3 as specified in Figure C-3-5? No Replace ...
Page 146 - Local Test; Figure C-3-6 Test connector connection diagram
C – 11 3.3 Local Test 3.3.1 Circuit test mode 3.3.1.1 Setting (1) Diagnostic test (set by menu) (2) Test connector Connect the test connector shown in Figure C-3-6 to the interface connector Figure C-3-6 Test connector connection diagram 3.3.1.2 Function After the settings outlined in Section 3.3.1....
Page 148 - People to People Technology
M-521369 4-96 Printed in Japan Oki Systems (Danmark) a.s. Park Alle 382DK-2625 VallensbaekDenmarkTel : 436 66500Fax : 436 66590 Oki Systems (France) S.A. 44-50 Avenue du General de Gaulle94240 L'Hay les RosesFranceTel : 0146 158000Fax : 0141 240040 Oki Systems (Italia) S.p.A. Centro Commerciale "...
