National Instruments cFP-PWM-520 - Manual
National Instruments cFP-PWM-520 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – mounts on a Compact FieldPoint backplane
- Page 4 – terminals are all internally connected,; Channel; COM
- Page 5 – Caution; Specifications; Pulse-Width Modulator Output Circuit
- Page 6 – Short-Circuit Protection; Detecting a Short-Circuit Condition; Configuring the Output; Resetting a Channel in a Short-Circuit Condition
- Page 7 – Overcurrent Protection; The amount of current through the channel; Power Supplies and Overcurrent Conditions
- Page 8 – Configuring the Output Channels; select; Period; from the Attribute menu.; Status Indicators; POWER; and; READY; indicator lights; Duty Cycle
- Page 9 – Upgrading Your FieldPoint Firmware; Isolation and Safety Guidelines; double insulation; Never
- Page 11 – Safety Guidelines for Hazardous Locations; not; Special Conditions for Hazardous Locations Use in Europe
- Page 12 – Output Characteristics; Output; Module
- Page 13 – Guaranteed trip current; Physical Characteristics; Weight
- Page 14 – Isolation voltage is verified by a dielectric withstand test.; Category II; Environmental; noncondensing
- Page 15 – Shock and Vibration; Hazardous Locations; Note; For UL and other safety certifications, refer to the
- Page 16 – Electromagnetic Compatibility; CE Compliance; Environmental Management; NI and the
- Page 17 – Waste Electrical and Electronic Equipment (WEEE); EU Customers; At the end of their life cycle, all products; RoHS; National Instruments; about China RoHS compliance, go to
- Page 18 – Where to Go for Support
FIELDPOINT
™
OPERATING INSTRUCTIONS
AND SPECIFICATIONS
FP-PWM-520 and
cFP-PWM-520
Eight-Channel, 5 V or 10–30 V PWM Output Module
These operating instructions describe how to install and use
the National Instruments FP-PWM-520 and cFP-PWM-520
pulse-width modulation modules (referred to inclusively as the
[c]FP-PWM-520). For details on configuring and accessing the
[c]FP-PWM-520 over a network, refer to the user manual for the
FieldPoint network module you are using.
Features
The [c]FP-PWM-520 is a FieldPoint pulse-width modulation
(PWM) output module with the following features:
•
Eight PWM sourcing output channels
•
0 to 100% duty-cycle capability with 12-bit resolution
•
Short-circuit protection for outputs
•
Outputs source 5 VDC or 10–30 VDC with user-provided
power supply
•
Independent configuration of the output period for each
channel from 1 to 65,535 ms in 1 ms increments
•
On/Off LED indicators
•
250 V
rms
CAT II continuous channel-to-ground isolation,
verified by 2,300 V
rms
, 5 s dielectric withstand test
•
–40 to 70 °C operation
•
Hot swappable
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
© National Instruments Corp. 3 FP-PWM-520 and cFP-PWM-520 Installing the cFP-PWM-520 The cFP-PWM-520 mounts on a Compact FieldPoint backplane (cFP-BP- x or cFP-180 x ), which provides operating power to the module. Installing the cFP-PWM-520 onto a powered backplane does not disrupt the operation of...
FP-PWM-520 and cFP-PWM-520 4 ni.com Wiring the [c]FP-PWM-520 The FP-TB- x terminal base has connections for each of the eight output channels and for an external power supply to power the output channels and field devices. The cFP-CB- x connector block provides the same connections. Each channel has...
© National Instruments Corp. 5 FP-PWM-520 and cFP-PWM-520 Install a 2 A maximum, fast-acting fuse between the external power supply and the V SUP terminal on each channel. Install a 1 A maximum, fast-acting fuse suitable for the load at the V OUT terminal. Figure 3 shows fuses where appropriate. Fig...
