National Instruments cFP-PG-522 - Manual
National Instruments cFP-PG-522 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – Align the captive screws on the cFP-PG-522 with the holes on
- Page 4 – Caution
- Page 5 – Pulse Output Circuit; Channel; COM
- Page 6 – In the ON state, the effective resistance between V; and COM; Configuring the Count-Input Channels; Attributes; Pulse Mode; Channel Commands; Channel Subset
- Page 7 – On Time; Resolution
- Page 9 – POWER; and; READY; indicator lights; Physical Channel
- Page 10 – Upgrading the FieldPoint Firmware; Isolation and Safety Guidelines; not
- Page 11 – following symbol stamped beside it:; Specifications; Output; Maximum output current
- Page 12 – Physical Characteristics; green output state indicators; Power Requirements; channels; Environmental; noncondensing; Shock and Vibration
- Page 13 – Safety; must; CE Compliance; Note; Declarations of Conformity Information
- Page 14 – Mechanical Dimensions; Where to Go for Support
323356B-01
May 2003
©
2002–2003 National Instruments Corp. All rights reserved.
FieldPoint™, National Instruments™, NI™, and ni.com™ are trademarks of National Instruments Corporation.
Product and company names mentioned herein are trademarks or trade names of their respective companies.
For patents covering National Instruments products, refer to the appropriate location:
Help»Patents
in your software,
the
patents.txt
file on your CD, or
ni.com/patents
.
FieldPoint Operating Instructions
FP-PG-522 and cFP-PG-522
Eight-Channel Pulse Generator
with 2 A, 5–30 VDC Sinking Outputs
These operating instructions describe how to install and use the
National Instruments FP-PG-522 and cFP-PG-522 pulse generator
modules (referred to inclusively as the [c]FP-PG-522). For details
on configuring and accessing the [c]FP-PG-522 over a network,
refer to the user manual for the FieldPoint network module you are
using.
Features
The [c]FP-PG-522 is a FieldPoint pulse generator module with the
following features:
•
Eight pulse-output channels
•
User-powered 2 A, 5–30 VDC sinking outputs
•
1 s, 10 ms, or 100
µ
s resolution setting, configurable per
channel
•
16-bit on-time and off-time settings
•
100% duty cycle pulse support
•
Finite and continuous pulse-generation modes
•
Active/Inactive LED indicators
•
2,300 V
rms
transient overvoltage protection
•
– 40 to 70 °C operation
•
Hot swappable
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
© National Instruments Corp. 3 FP-PG-522 and cFP-PG-522 To install the cFP-PG-522, refer to Figure 2 and complete the following steps: 1. Align the captive screws on the cFP-PG-522 with the holes on the backplane. The alignment keys on the cFP-PG-522 prevent backward insertion. 2. Press firmly to se...
FP-PG-522 and cFP-PG-522 4 ni.com Wiring the [c]FP-PG-522 The FP-TB- x terminal base has connections for each of the eight output channels and for an external power supply to power the output channels and field devices. The cFP-CB- x connector block provides the same connections. Each channel has on...
© National Instruments Corp. 5 FP-PG-522 and cFP-PG-522 Table 1 lists the terminal assignments for the signals of each channel. Terminal assignments are also listed on the side panel of the cFP-PG-522 and under the slide-in card on the front of the FP-PG-522. Pulse Output Circuit The [c]FP-PG-522 ou...
