National Instruments FP-Al-110 - Manual
National Instruments FP-Al-110 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – terminal base has connections for each of the eight; terminals are; terminals so that the maximum current through any V terminal
- Page 4 – is 2 A or less and the maximum current through any V; terminal; Do not connect both current and voltage inputs; Caution; Cascading power between two modules defeats; Terminal Assignments; Channel; COM; Install a 2 A, fast-acting fuse on each V; Install a 2 A, fast-acting fuse on each I; Install a 2 A maximum, fast-acting fuse on each V
- Page 5 – The input ranges for voltage signals are 0 –1 V, 0 –5 V, 0 –10 V,; Voltage Source without External Power Supply
- Page 6 – Voltage Source with External Power Supply
- Page 7 – Current Source without External Power Supply; Input Ranges
- Page 8 – Overranging; 0 V range is; Filter Settings; number of channels with 50 Hz filter
- Page 9 – Status Indicators; POWER; Upgrading the FieldPoint Firmware; fpmatrix; Isolation and Safety Guidelines; hazardous voltages; double insulation
- Page 10 – Never
- Page 11 – Safety Guidelines for Hazardous Locations; not; Special Conditions for Safe Use in Europe
- Page 12 – Safety Guidelines for Hazardous Voltages; Specifications; Input Characteristics
- Page 13 – Effective resolution by input signal range and filter setting; Voltage Inputs; Overvoltage protection
- Page 15 – Note; Current Inputs
- Page 16 – Physical Characteristics; Power Requirements; Environmental
- Page 17 – Safety; FCC Part 15A above 1 GHz; For EMC compliance, you
- Page 18 – CE Compliance; Refer to the Declaration of Conformity (DoC) for; Mechanical Dimensions
- Page 19 – Where to Go for Support
FieldPoint
™
Operating Instructions
FP-AI-110 and cFP-AI-110
Eight-Channel, 16-Bit Analog Input Modules
These operating instructions describe how to install and use the
FP-AI-110 and cFP-AI-110 analog input modules (referred to
inclusively as the [c]FP-AI-110). For information about
configuring and accessing the [c]FP-AI-110 over a network, refer
to the user manual for the FieldPoint network module you are
using.
Features
The [c]FP-AI-110 is a FieldPoint analog input module with the
following features:
•
Eight analog voltage or current input channels
•
Eight voltage input ranges: 0 –1 V, 0 –5 V, 0 –10 V,
±
60 mV,
±
300 mV,
±
1 V,
±
5 V, and
±
10 V
•
Three current input ranges: 0 –20, 4 –20, and
±
20 mA
•
16-bit resolution
•
Three filter settings: 50, 60, and 500 Hz
•
250 V
rms
CAT II continuous channel-to-ground isolation,
verified by 2,300 V
rms
dielectric withstand test
•
– 40 to 70 °C operation
•
Hot swappable
Installing the FP-AI-110
The FP-AI-110 mounts on a FieldPoint terminal base (FP-TB-
x
),
which provides operating power to the module. Installing the
FP-AI-110 onto a powered terminal base does not disrupt the
operation of the FieldPoint bank.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
© National Instruments Corp. 3 FP-AI-110 and cFP-AI-110 (10 lb ⋅ in.) of torque. The nylon coating on the screws prevents them from loosening. Figure 2. Installing the cFP-AI-110 Wiring the [c]FP-AI-110 The FP-TB- x terminal base has connections for each of the eight input channels and for an extern...
FP-AI-110 and cFP-AI-110 4 ni.com is 2 A or less and the maximum current through any V SUP terminal is 1 A or less. Install a 2 A maximum, fast-acting fuse between the external power supply and the V terminal on each channel. The wiring diagrams in this document show fuses where appropriate. Table 1...
© National Instruments Corp. 5 FP-AI-110 and cFP-AI-110 Taking Measurements with the [c]FP-AI-110 The [c]FP-AI-110 has eight single-ended input channels. All eight channels share a common ground reference that is isolated from other modules in the FieldPoint system. Figure 3 shows the analog input c...
