Napoleon EF31H - Manual - manualsarea.com

Page 2 - TABLE of CONTENTS; PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE

W415-0469 / A / 01.04.05 2 7 ELECTRICAL CONNECTION 8 LIGHT REPLACEMENT 9-10 REPLACEMENTS Ordering Replacement PartsReplacement PartsAccessories 11 TROUBLE SHOOTING GUIDE 12 RATING PLATE LOCATION PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE NOTE: Changes, other than editorial, are denoted by a vert...

Page 4 - SAVE THESE INSTRUCTIONS.; IMPORTANT INSTRUCTIONS

W415-0469 / A / 01.04.05 4 Your new fireplace may be installed into an existing ma-sonry or zero clearance fireplace. It may also be installedusing a prefabricated cabinet available from your dealer ormay be built into a wall. For the best effect, install the fire-place out of direct sunlight. 1. RE...

Page 5 - MANTEL; FINISHING; MAINTENANCE

5 W415-0469 / A / 01.04.05 Sides................. 0 mm / 0 inches Sides................. 0 mm / 0 inches Floor................. 0 mm / 0 inches Top 0 mm / 0 inches The minimum distance from the top of the unit that themantel can be installed is 0", at any depth. When using paint or lacquer to fi...

Page 6 - GLASS REMOVAL

W415-0469 / A / 01.04.05 6 1. Position logs #1 and #2 as shown.The diffuser base has been moulded to cradle the logs. Be sure not to block the vertical groove running down the Be sure not to block the vertical groove running down the Be sure not to block the vertical groove running down the Be sure ...

Page 7 - ELECTRICAL CONNECTION; HARD WIRING CONNECTION; OPTIONAL SCREEN INSTALLATION

7 W415-0469 / A / 01.04.05 This fireplace requires a 15 amp, 120 volt and 60 hzcircuit. The fireplace should be on its own circuit. Ifthere are other appliances on the same circuit, this maycause the circuit breaker or fuse to blow when the fire-place heater is in operation. The unit comes with a 6'...

Page 8 - LIGHT REPLACEMENT

W415-0469 / A / 01.04.05 8 There are two methods to replace the light: There are two methods to replace the light: There are two methods to replace the light: There are two methods to replace the light: There are two methods to replace the light:In either method, the electrical circuit breaker must ...

Page 9 - REPLACEMENTS; REPLACEMENT PARTS

9 W415-0469 / A / 01.04.05 # PART NO. DESCRIPTION 1 W497-0002 PLASTIC DIFFUSER 2 W062-0019 FAN / HEATER ASSEMBLY 3 W380-0016 THERMOSTAT KNOB 4 W387-0005 75 WATT QUARTZ LIGHT BULB 5 W435-0006 FLAME EFFECT MOTOR 6 W660-0040 THERMOSTAT SWITCH 7 W660-0023 MAIN POWER SWITCH 8 W010-1266 FLAME EFFECT ASSEM...

Page 11 - TROUBLE SHOOTING GUIDE; SYMPTOM

11 W415-0469 / A / 01.04.05 Flame light, but no - Flame generator motor has burned out. - Consult your local dealer. movement in the flame - Flame generator has come loose. - Remove the access panel and check to make sure the flame generator is in the flamegenerator bracket, and is secured to themot...

Page 12 - RATING PLATE LOCATION

W415-0469 / A / 01.04.05 12 Method 2: 1. Remove the two screws holding the glass retainer andpull forward to remove the glass. Place the glass and re-tainer in a safe spot. 2. Remove the five screws holding the defuser screen. Pullthe top two corners in towards the center and remove fromthe unit. 3....

Napoleon EF31H - Manual

Table of Contents:

Summary

Other Napoleon Models