Napoleon Arlington GDS20N - Manuals

7 W415-0496 / B / 08.10.05 BLOWER INSTALLATION Blower ( SEE LOCATION AND CLEARANCES ) 1. Cut and remove the tie securing the blower switch wires to the heat shield. 2. Connect the white wire coming from below the unit to the terminal on the blower. 3. Connect the black blower wire to the black wire ...

8 W415-0496 / B / 08.10.05 AIR TERMINAL INSTALLATIONS ***** R e c o m m e n d e d t o p r e v e n t c o n d e n s a t i o n o n w i n d o w s a n d t h e r m a l b r e a k a g e * * * * * * * * * * It is recommended to use a heat shield and to maximize the distance to vinyl clad sof f its. * * * * *...

9 W415-0496 / B / 08.10.05 Use only Wolf Steel, Simpson Dura-Vent, Selkirk DirectTemp or American Metal Amerivent venting components.For Simpson Dura-Vent, Selkirk Direct Temp and AmericanMetal Amerivent, follow the installation procedure providedwith the venting components.All outer pipe joints of ...

10 W415-0496 / B / 08.10.05 Use the GD201 periscope kit to locate the air terminationabove grade. The periscope must be installed so that whenfinal grading is completed, the bottom air slot is located aminimum of 12 inches above grade. The maximum allow-able vent length depends on the fireplace, as ...

11 W415-0496 / B / 08.10.05 ELBOW VENT LENGTH VALUES DEFINITIONS HORIZONTAL TERMINATION REQUIREDV E R T I C A LRISE IN FEET(V T ) CALCULATED HORIZONTAL VENT RUNPLUS OFFSETS IN FEET (H T ) FIGURE 5 45º FIGURE 6 90° H 1 H 2 when (H T ) < (V T ) for the following symbols used in the venting calcula-...

13 W415-0496 / B / 08.10.05 VERTICAL TERMINATION Example 3: V 1 = 5 ft V 2 = 10 ft V T = V 1 + V 2 = 5 + 10 = 15 ft H 1 = 3 ft H 2 = 2.5 ft H R = H 1 + H 2 = 3 + 2.5 = 5.5 ft H O = .03(one 45º elbow + three 90º elbows - 135º)= .03(45+90+90+90-135)=5.4 H T = H R + H O = 5.5 + 5.4 = 10.9 ft H T + V T ...

15 W415-0496 / B / 08.10.05 This application occurs when venting through an exteriorwall. Having determined the air terminal location, cut andframe a hole in an exterior wall with a minimum rectangleopening of 10" x 9". IMPORTANT: FOR OPTIMUM PERFORMANCE, THE STOVE PIPESHOULD RISE ¼" PER...

16 W415-0496 / B / 08.10.05 4. If more than one length of liner needs to be used to reach the stove, couple them together as illustrated in FIGURE 24 . Seal the joints using the same procedure as described above.The vent system must be supported approximately every10 feet along a horizontal run. Use...

17 W415-0496 / B / 08.10.05 1. Attach the adjustable pipe to the last section of rigid piping. Secure with screwsand seal. 2. Install the 4" aluminium flex- ible liner to the stove. Securewith 3 screws and flat wash-ers. Seal the joint and screwholes using high tempera-ture sealant. 3. Run a bea...

18 W415-0496 / B / 08.10.05 1. Lift the top cast piece off of the unit. 2. Detach the front cast piece from the side pieces by removing the screws from the brackets located in the upperinside corners. 3. Slide the front straight up to remove. FINISHING GLASS DOOR INSTALLATION AND REMOVAL CAST FRONT ...

19 W415-0496 / B / 08.10.05 LOG PLACEMENT LOGO PLACEMENT Remove the backing from the the logo and position ontothe control door as shown. It is not necessary to remove the cast front, however,this will make for a more simple log installation. In order to assemble the log set, the door must be remove...

20 W415-0496 / B / 08.10.05 Purge all gas lines with the glass door removed. Assurethat a continuous gas flow is at the burner before closingthe door. The on-off switch is located on the back of the unit at thetop right corner on model GDS20. When lit for the first time, the fireplace will emit a sl...

21 W415-0496 / B / 08.10.05 Adjust the pilot screw to provide properly sized flame. Turnin a clockwise direction to reduce the gas flow. FIGURE 34 FIGURE 35 Air shutter adjustment must only be done by a qualified gas installer! FIGURE 36 ADJUSTMENTS PILOT BURNER ADJUSTMENT VENTURI ADJUSTMENT TURN OF...

22 W415-0496 / B / 08.10.05 Contact your dealer for questions concerning prices andavailability of replacement parts. Normally all parts canbe ordered through your Napoleon dealer or distributor.When ordering replacement parts always give the fol-lowing information: 1. M ODEL & S ERIAL N UMBER O...

24 W415-0496 / B / 08.10.05 Pilot will not light. - check if pilot can be lit by a match- check that the wire is connected to the push button ignitor.- check if the push button ignitor needs tightening.- replace the wire if the wire insulation is broken or frayed.- replace the electrode if the ceram...

26 W415-0496 / B / 08.10.05 W olf Steel Fir eplace Ser vice Histor y This fireplace must be serviced annually depending on usage. Date Service T e chnician Name Service Performed Special Concerns Dealer Name