Page 2 - PROPOSITION 65 WARNING
PAGE 2 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) Engine exhaust and some of its constituents, and some dust created of California to cause cancer, birthdefects and other reproductive harm. by power sanding, sawing, grinding, drilling and other construction activities contain...
Page 3 - SILICOSIS WARNING; SILICOSIS/RESPIRATOR WARNINGS
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 3 Grinding/cutting/drilling of masonry, concrete, metal andother materials with silica in their composition may giveoff dust or mists containing crystalline silica. Silica is abasic component of sand, quartz, brick clay, granit...
Page 4 - TABLE OF CONTENTS; Specification and part number; NOTE
PAGE 4 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) TABLE OF CONTENTS Multiquip Mix N' Go —Portable Concrete Mixer Proposition 65 Warning ............................................. 2Silicosis/Respiratory Warnings .................................. 3Table of Contents ...........
Page 5 - PARTS ORDERING PROCEDURES; Ordering parts has never been easier!; Choose from three easy options:; Order via Internet; Order; Order via Fax
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 5 PARTS ORDERING PROCEDURES www .multiquip .com Ordering parts has never been easier! Choose from three easy options: WE ACCEPT ALL MAJOR CREDIT CARDS! When ordering parts, please supply: R Dealer Account Number R Dealer Name a...
Page 6 - SAFETY INFORMATION; SAFETY MESSAGES; DANGER
PAGE 6 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) SAFETY INFORMATION Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages ...
Page 7 - GENERAL SAFETY
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 7 GENERAL SAFETY CAUTION NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or ...
Page 8 - MIXER SAFETY
PAGE 8 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) SAFETY INFORMATION MIXER SAFETY DANGER NEVER operate the equipment in an explosive atmosphere or near combustible materials. An explosion or fire could result causing severe bodily harm or even death. DO NOT mix flammable ...
Page 9 - GENERATOR SAFETY; Power Cord/Cable Safety
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 9 SAFETY INFORMATION FUEL SAFETY (GASOLINE MODELS ONLY) DANGER DO NOT add fuel to equipment if it is placed inside truck bed with plastic liner. Possibility exists of explosion or fire due to static electricity. DO NOT star...
Page 10 - TRANSPORTING SAFETY; ENVIRONMENTAL SAFETY
PAGE 10 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) SAFETY INFORMATION TRANSPORTING SAFETY CAUTION NEVER allow any person or animal to stand underneath the equipment while lifting. NOTICE ALWAYS make sure forklift forks are inserted into pockets (if applicable) as far as p...
Page 11 - OPERATION AND SAFETY DECALS; Machine Safety Decals
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 11 OPERATION AND SAFETY DECALS Machine Safety Decals The Mix N' Go mixer is equipped with a number of safety decals. These decals are provided for operator safety and maintenanceinformation. The illustration below and on the ne...
Page 13 - MIX N' GO MIXER — SPECIFICATIONS; ti
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 13 MIX N' GO MIXER — SPECIFICATIONS s n o i t a c i f i c e p S r e x i M o G ' N x i M . 2 e l b a T t h g i e H ) m m 6 . 3 6 8 ( . n i 4 3 h t d i W ) m m 2 . 4 8 5 ( . n i 8 / 5 - 3 2 h t g n e L ) m m 2 . 9 1 2 , 1 ( . n i...
Page 14 - Mixer Dimensions
PAGE 14 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) MIX N' GO MIXER — DIMENSIONS (MIXER) Figure 1. Mix N' Go Mixer Dimensions
Page 15 - Figure 2. Electric Motor
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 15 MIX N' GO MIXER — DIMENSIONS (ELECTRIC MOTOR) Figure 2. Electric Motor
Page 16 - MIX N' GO MIXER — GENERAL INFORMATION
PAGE 16 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) MIX N' GO MIXER — GENERAL INFORMATION APPLICATION This mixer is only intended for the production of concrete and mortar . The mixer must be used for its intended purposes and is not suitable for the mixing of flammable or exp...
Page 17 - MIX N' GO MIXER — MIXER COMPONENTS; Figure 4. Mixer Components; Mixer
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 17 MIX N' GO MIXER — MIXER COMPONENTS Figure 4. Mixer Components Figure 4 shows the basic components of the Mix N' Go Mixer .
Page 18 - MIX N' GO MIXER — BASIC ENGINE; WARNING
PAGE 18 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) Figure 5. Engine Controls and Components INITIAL SERVICING The engine (Figure 5) must be checked for proper lubrication andfilled with fuel prior to operation. Refer to the manufacturers enginemanual for instructions and deta...
Page 20 - MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS
PAGE 20 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) 6. Tip mixer onto mouth as shown in Figure 10, and insert support stand into frame swivel point. 9. Before attempting to lift mixer, locate the frame locking clip. Attach the locking clip as shown in Figure 12. This will prev...
Page 21 - Explosive Fuel
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 21 MIX N' GO MIXER — PRE-INSPECTION (GASOLINE ENGINE) Figure 15. Engine Oil Dipstick (Removal) 3. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. 4. If the oil...
Page 25 - MIX N' GO MIXER — MAINTENANCE; Check the gearbox oil level; monthly
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 25 MIX N' GO MIXER — MAINTENANCE Maintenance Gearbox Oil Check 1. Position the mixer on a level surface and place a support block under the front of the mixer frame as shown in Figure 29. Thiswill level the mixer. 2. NEVER! che...
Page 28 - MIX N' GO MIXER — PREPARATION FOR LONG -TERM STORAGE; Mixer Storage; Run the engine until the fuel is completely consumed
PAGE 28 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) MIX N' GO MIXER — PREPARATION FOR LONG -TERM STORAGE Mixer Storage For storage of the mixer for over 30 days, the following isrecommended: Drain the fuel tank completely, or add STA-BIL to thefuel. Run the engine until th...
Page 29 - NOTE PAGE
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 29 NOTE PAGE
Page 32 - MIX N' GO MIXER — EXPLANATION OF CODE IN REMARKS COLUMN; SAMPLE PARTS LIST; REMARKS Column
PAGE 32 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) MIX N' GO MIXER — EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if t...
Page 33 - MIX N' GO MIXER — SUGGESTED SPARE PARTS; MIX N' GO MIXER 1 TO 3 UNITS
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 33 MIX N' GO MIXER — SUGGESTED SPARE PARTS MIX N' GO MIXER 1 TO 3 UNITS 1 to 3 Units Qty. P/N Description 2 ............ DM1840 ................ V-BELT, A23 (ELECTRIC MOTOR)2 ............ MS-01 ................... V-BELT, A24 (...
Page 34 - MIX N' GO MIXER — NAME PLATE AND DECALS; NAME PLATE AND DECALS
PAGE 34 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) MIX N' GO MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS WA RNIN G! ALA RM A! AVE RTIS SEM ENT ! ENG LISH - W ARN ING ! TO RED UCE THE RIS K O F IN JUR Y, U SER MUS T R EAD AND UND ERS TAN D IN STR UCT ION MAN UAL ESP AÑ...
Page 35 - DECAL: WARNING MAINTENANCE
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 35 MIX N' GO MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS NAMEPLATE AND DECALS. NO PART NO PART NAME QTY. REMARKS 1 * DCL251 DECAL: WARNING MQ 1 2 * 510165 DECAL: MQ MIX N GO 1 3 DECAL: NAMEPLATE ...........................
Page 44 - TERMS AND CONDITIONS OF SALE — PARTS
PAGE 44 —MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B....
Page 45 - NOTES
MIX N' GO MIXER — OPERATION AND PARTS MANUAL — REV. #3 (09/20/11) — PAGE 45 NOTES
Page 46 - Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; CANADA; OPERATION AND PARTS MANUAL
Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Offi ce MQ Parts Department 18910 Wilmington Ave.Carson, CA 90746 Contact: [email protected] Tel. (800) 421-1244Fax (800) 537-3927 800-427-1244310-537-3700 Fax: ...
