Page 3 - HERE'S HOW TO GET HELP; PARTS DEPARTMENT
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 3 HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBERON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-5...
Page 4 - TABLE OF CONTENTS; Specification and part number; NOTE
PAGE 4 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) TABLE OF CONTENTS Here's How To Get Help ............................................ 3Table Of Contents ..................................................... 4Parts Ordering Procedures ..........................................
Page 5 - PARTS ORDERING PROCEDURES; please supply the following information:; Direct TOLL-FREE access
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 5 PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ Dealer account number ❒ ❒ ❒ ❒ ❒ Dealer name and address ❒ ❒ ❒ ❒ ❒ Shipping address (if different than billing address) ❒ ❒ ❒ ...
Page 6 - MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS
PAGE 6 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) Accidental Starting ALWAYS place the circuit breaker or power ON/OFF switch in the OFF position when the pump is not in use. Respiratory Hazard A LWAY S w e a r a p p r o ve d r e s p i ra t o r y protection. Equipment Damage...
Page 7 - MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS; Accidental Starting; Respiratory Hazard; Equipment Damage Messages; Sight and Hearing hazard
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 7 MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting ALWAYS place the engine ON/OFF switch in the OFF position, and remove the ignition key when the machine is not in use. Respiratory Hazard A LWAY S w e a r a...
Page 8 - RULES FOR SAFE OPERATION
PAGE 8 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) RULES FOR SAFE OPERATION ■ ALWAYS refuel in a well-ventilated area, away from sparks and open flames. ■ ALWAYS use extreme caution when working with flammable liquids. When refueling, stop the engine and allow it to cool. DO ...
Page 9 - Maintenance Safety
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 9 ■ High Temperatures – Always stop engine and allow the engine to cool before adding fuel, oil or performing serviceand maintenance functions. Contact with hot components can cause serious burns. ■ NEVER disconnect any "...
Page 10 - Emergencies; keep a phone on the job site
PAGE 10 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) Emergencies ■ ALWAYS know the location of the nearest fire extinguisher. ■ ALWAYS know the location of the nearest first aid kit. ■ In emergencies always know the location of the nearest phone or keep a phone on the job site...
Page 11 - OPERATION AND SAFETY DECALS; Machine Safety Decals
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 11 OPERATION AND SAFETY DECALS Machine Safety Decals The Mix N' Go mixer is equipped with a number of safety decals. These decals are provided for operator safety and maintenanceinformation. The illustration below and on the ...
Page 13 - MIX N' GO MIXER — SPECIFICATIONS
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 13 MIX N' GO MIXER — SPECIFICATIONS s n o i t a c i f i c e p S r e x i M o G ' N x i M . 2 e l b a T t h g i e H ) m m 6 . 3 6 8 ( . n i 4 3 h t d i W ) m m 2 . 4 8 5 ( . n i 8 / 5 - 3 2 h t g n e L ) m m 2 . 9 1 2 , 1 ( . n...
Page 15 - Figure 2. Electric Motor
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 15 MIX N' GO MIXER — DIMENSIONS (ELECTRIC MOTOR) Figure 2. Electric Motor
Page 16 - MIX N' GO MIXER — GENERAL INFORMATION
PAGE 16 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) MIX N' GO MIXER — GENERAL INFORMATION APPLICATION This mixer is only intended for the production of concrete and mortar . The mixer must be used for its intended purposes and is not suitable for the mixing of flammable or ex...
Page 17 - MIX N' GO MIXER — MIXER COMPONENTS; Figure 4. Mixer Components; Mixer
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 17 MIX N' GO MIXER — MIXER COMPONENTS Figure 4. Mixer Components S T N I H G N I X I M . 3 e l b a T S N O I T A C I L P P A X I M S O I T A R S E I T I T N A U Q H C T A B H C T A B . X O R P P A T U P T U O . s b l 2 1 1 T ...
Page 18 - DANGER; MIX N' GO MIXER — BASIC ENGINE; WARNING
PAGE 18 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) Figure 5. Engine Controls and Components INITIAL SERVICING The engine (Figure 5) must be checked for proper lubrication andfilled with fuel prior to operation. Refer to the manufacturers enginemanual for instructions and det...
Page 20 - MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS
PAGE 20 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) 6. Tip mixer onto mouth as shown in Figure 10, and insert support stand into frame swivel point. 9. Before attempting to lift mixer, locate the frame locking clip. Attach the locking clip as shown in Figure 12. This will pre...
Page 21 - Explosive Fuel
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 21 MIX N' GO MIXER — PRE-INSPECTION (GASOLINE ENGINE) Figure 15. Engine Oil Dipstick (Removal) 3. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. 4. If the o...
Page 25 - MIX N' GO MIXER — MAINTENANCE; Check the gearbox oil level; monthly; before operating mixer. Low oil level or no
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 25 MIX N' GO MIXER — MAINTENANCE Maintenance Gearbox Oil Check 1. Position the mixer on a level surface and place a support block under the front of the mixer frame as shown in Figure 29. Thiswill level the mixer. 2. NEVER! c...
Page 28 - MIX N' GO MIXER — PREPARATION FOR LONG -TERM STORAGE; Mixer Storage; Run the engine until the fuel is completely consumed
PAGE 28 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) MIX N' GO MIXER — PREPARATION FOR LONG -TERM STORAGE Mixer Storage For storage of the mixer for over 30 days, the following isrecommended: z Drain the fuel tank completely, or add STA-BIL to thefuel. z Run the engine until t...
Page 29 - NOTE PAGE
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 29 NOTE PAGE
Page 32 - Items Found In the “Remarks” Column; Items Found In the “Items Number” Column; MIX N' GO MIXER — EXPLANATION OF CODE IN REMARKS COLUMN
PAGE 32 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) How to read the marks and remarks used in this partsbook. Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serialnumber range (inclusive) where a particular part is used. Model Number-Wher...
Page 33 - MIX N' GO MIXER — SUGGESTED SPARE PARTS; MIX N' GO MIXER 1 TO 3 UNITS
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 33 MIX N' GO MIXER — SUGGESTED SPARE PARTS MIX N' GO MIXER 1 TO 3 UNITS 1 to 3 Units Qty. P/N Description 2 ............ DM1840 ................ V-BELT, A23 (ELECTRIC MOTOR)2 ............ MS-01 ................... V-BELT, A24...
Page 34 - MIX N' GO MIXER — NAME PLATE AND DECALS; NAME PLATE AND DECALS
PAGE 34 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) MIX N' GO MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS WA RNIN G! ALA RM A! AVE RTIS SEM ENT ! ENG LISH - W ARN ING ! TO RED UCE THE RIS K O F IN JUR Y, U SER MUS T R EAD AND UND ERS TAN D IN STR UCT ION MAN UAL ESP A...
Page 35 - DECAL: WARNING MAINTENANCE
MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 35 MIX N' GO MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS NAMEPLATE AND DECALS. NO PART NO PART NAME QTY. REMARKS 1 * DCL251 DECAL: WARNING MQ 1 2 * 510165 DECAL: MQ MIX N GO 1 3 DECAL: NAMEPLATE .........................
Page 40 - TERMS AND CONDITIONS OF SALE — PARTS
PAGE 40 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05) TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect orprepaid with the charges added to the invoice.All shipments are F.O.B. ...
Page 42 - OPERATION AND PARTS MANUAL
MULTIQUIP INC. POST OFFICE BOX 6254CARSON, CA 90749310-537-3700 • 800-421-1244FAX: 310-537-3927E-MAIL: [email protected]: multiquip.com Atlanta • Boise • Dallas • Houston • Newark Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AN...