Page 2 - PROPOSITION 65 WARNING
PAGE 2 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) PROPOSITION 65 WARNING
Page 3 - NOTES
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 3 NOTES
Page 4 - Component Drawings; Terms and Condition of Sale; TABLE OF CONTENTS; Specification and part number are subject to
PAGE 4 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) MT75HS TampingRammer Proposition 65 Warning ......................................... 2Table Of Contents ................................................. 4Parts Ordering Procedures ................................... 5Safety ...
Page 5 - PARTS ORDERING PROCEDURES; Ordering parts has never been easier!; Choose from three easy options:; Order via Internet; Order; Order via Fax
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 5 PARTS ORDERING PROCEDURES www .multiquip .com Ordering parts has never been easier! Choose from three easy options: WE ACCEPT ALL MAJOR CREDIT CARDS! When ordering parts, please supply: ❒ Dealer Account Number ❒ Dealer Name an...
Page 6 - SAFETY INFORMATION; SAFETY MESSAGES; DANGER
PAGE 6 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) SAFETY INFORMATION Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages ...
Page 7 - GENERAL SAFETY; RAMMER SAFETY
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 7 SAFETY INFORMATION GENERAL SAFETY CAUTION NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices requi...
Page 8 - ENGINE SAFETY; FUEL SAFETY
PAGE 8 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) SAFETY INFORMATION ENGINE SAFETY DANGER The engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. The engine of this equipment requires an adequate...
Page 9 - TRANSPORTING SAFETY; ENVIRONMENTAL SAFETY
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 9 SAFETY INFORMATION TRANSPORTING SAFETY CAUTION NEVER allow any person or animal to stand underneath the equipment while lifting. NOTICE Before lifting, make sure that the equipment parts (hook and vibration insulator) are ...
Page 10 - GENERAL INFORMATION
PAGE 10 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) Definition of Tamping Rammer The Mikasa MT-75HS Tamping Rammer is a powerfulcompacting tool capable of applying a tremendous force inconsecutive impacts to a soil surface. Its applications includesoil compacting for backfilli...
Page 11 - NOTE; SPECIFICATIONS
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 11 NOTE Specifications are general and are subject to change without notice. If exactmeasurements are required, equipment should be weighed and measured. s n o i t a c i f i c e p S r e m m a R S H 5 7 - T M . 1 e l b a T L E D ...
Page 12 - COMPONENTS
PAGE 12 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) L1. A Returned Material Authorization must be approved by Multiquip prior to shipment. A copy of the Authorization must accompany the shipment to the designated Warehouse. A copy of the original Multiquip invoice to the custo...
Page 13 - Engine; Figure 4. Engine Oil Dipstick; Rammer Gearbox and Spring Cylinder Oil Bath; Check the oil level through the oil level sight glass (Figure 2); DO NOT; use your rammer until this section is thoroughly; Figure 2. Foot Housing Sight Glass; OPERATION
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 13 Failure to understand the operation of the MT-60HS Tamping Rammer could result in severedamage to the rammer or personal injury. Engine 1. Fill the fuel tank (Figure 3 ) with unleaded gasoline. At the same time, check the eng...
Page 14 - Inspection
PAGE 14 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) 5. If engine fails to start, move the choke lever (Figure 5) to the half open position to avoid flooding. 6. Repeat steps 1 thru 5. 7. If t he engine does not star t af ter repeated attempts,check the spark plug for excess fu...
Page 15 - Figure 9. Drain Plug
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 15 Stopping The Engine Normal Shutdown 1. Move throttle lever quickly from the FULL OPEN to IDLE position (Figure 11) and run the engine for three minutes atlow speed. After the engine cools , turn the engine start/stop switch t...
Page 16 - Maintenance; Perform the scheduled maintenance procedures as indicated:; DAILY; Remove or clean the filter at the bottom of the tank.; CLEANING THE OIL TANK; Remove the cock holder cover, oil hose, red and black lead; MAINTENANCE
PAGE 16 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) Maintenance Perform the scheduled maintenance procedures as indicated: DAILY ■ Thoroughly remove dirt and oil from the engine and controlarea. Clean or replace the air cleaner elements as necessary.Check and retighten all fas...
Page 17 - Figure 14. Air Cleaner
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 17 2. Remove the bolts that secure the oil tank to the fuel tank, and drain all oil from the tank. 3. Remove cock holder, then clean strainer and cock holder in a kerosene solution. 4. Make sure every part is clean and dry, then...
Page 18 - TROUBLESHOOTING
PAGE 18 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) G N I T O O H S E L B U O R T E N I G N E . 4 E L B A T M O T P M Y S M E L B O R P E L B I S S O P N O I T U L O S t r a t s o t t l u c i f f i D g u l p k r a p s t u b e l b a li a v a s i l e u F e l b a li a v a r e w o...
Page 20 - EXPLANATION OF CODES IN THE REMARKS COLUMN; SAMPLE PARTS LIST; REMARKS Column
PAGE 20 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) EXPLANATION OF CODES IN THE REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any ...
Page 21 - MT-75HS Tamping Rammer; MT-75HS Tamping Rammer; SUGGESTED SPARE PARTS
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 21 MT-75HS Tamping Rammer 1 to 3 Units Qty. P/N Description 1 ......... 956300130 .......... LEVER, THROTTLE LEVER1 ......... 956106040 .......... WIRE, THROTTLE ASSY1 ......... 402010110 .......... SPRING, RETURN3 ......... 354...
Page 22 - NAMEPLATE AND DECALS; Mikasa
PAGE 22 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) NAMEPLATE AND DECALS Mikasa Mikasa MT-75HS 6 3650 ~ 3850 RPM NPA 90 1 2 3 4 NAMEPLATE 5 7 8 NPA-333 9 14 DO NOT ALLOW WATER TO ENTER FUEL AND OIL TANKS NPA-599 10 SAE 10W-30 MOTOR OIL 11 CAUTION NPA-91 J 12 ON NAP-484 NO OFF ...
Page 23 - MT-75HS — NAME PLATES AND DECALS; PART NAME
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 23 MT-75HS — NAME PLATES AND DECALS NO. PART NO. PART NAME QTY. REMARKS 1 * 920106460 DECAL: MIKASA MARK 1 2 * 920203980 DECAL: ELEMENT SET 1 3 * 920203290 DECAL: READ OWNER'S MANUAL 1 4 PLATE: SERIAL NO. ..........................
Page 24 - CRANKCASE AND ENGINE ASSY.
PAGE 24 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) CRANKCASE AND ENGINE ASSY. CRANKCASE AND ENGINE ASSY.
Page 26 - CYLINDER GUIDE AND FOOT ASSY.; GUIDE CYLINDER AND FOOT ASSY.
PAGE 26 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) EXCLUDES ITEMS 61, 62 & 63 CYLINDER GUIDE AND FOOT ASSY. GUIDE CYLINDER AND FOOT ASSY.
Page 27 - CYLINDER GUIDE AND FOOT ASSY.
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 27 CYLINDER GUIDE AND FOOT ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 352423290 PISTON PIN 1 2 080100150 STOP RING R-15 2 3 355334300 PISTON ROD 1 4 355447240 PISTON END 1 5 020316130 NUT M16, P1.5 ................................
Page 28 - TANK AND HANDLE ASSY.
PAGE 28 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) TANK AND HANDLE ASSY. TANK AND HANDLE ASSY.
Page 32 - CRANKCASE AND CYLINDER ASSY.; ROBIN EC12HS ENGINE — CRANKCASE ASSY.
PAGE 32 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) CRANKCASE AND CYLINDER ASSY. ROBIN EC12HS ENGINE — CRANKCASE ASSY.
Page 34 - CRANKSHAFT AND PISTON ASSY.; ROBIN EC12HS ENGINE — CRANKSHAFT AND PISTON ASSY.
PAGE 34 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) CRANKSHAFT AND PISTON ASSY. ROBIN EC12HS ENGINE — CRANKSHAFT AND PISTON ASSY.
Page 36 - ROBIN EC12HS ENGINE — GOVERNOR ASSY.
PAGE 36 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) GOVERNOR ASSY. ROBIN EC12HS ENGINE — GOVERNOR ASSY.
Page 38 - MUFFLER AND AIR CLEANER ASSY.; ROBIN EC12HS ENGINE — MUFFLER/AIR CLEANER ASSY.
PAGE 38 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) MUFFLER AND AIR CLEANER ASSY. ROBIN EC12HS ENGINE — MUFFLER/AIR CLEANER ASSY.
Page 40 - CARBURETOR AND OIL PUMP ASSY.; ROBIN EC12HS ENGINE — CARBURETOR ASSY.
PAGE 40 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) CARBURETOR AND OIL PUMP ASSY. ROBIN EC12HS ENGINE — CARBURETOR ASSY.
Page 42 - RECOIL STARTER AND BLOWER ASSY.; ROBIN EC12HS ENGINE — RECOIL STARTER ASSY.
PAGE 42 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) RECOIL STARTER AND BLOWER ASSY. ROBIN EC12HS ENGINE — RECOIL STARTER ASSY.
Page 44 - ROBIN EC12HS ENGINE — ELECTRIC DEVICE ASSY.
PAGE 44 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) MAGNETO ASSY. ROBIN EC12HS ENGINE — ELECTRIC DEVICE ASSY.
Page 46 - ROBIN EC12HS ENGINE — LOOSE PARTS
PAGE 46 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) LOOSE PARTS ASSY. ROBIN EC12HS ENGINE — LOOSE PARTS
Page 48 - TERMS AND CONDITION OF SALE — PARTS
PAGE 48 — MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) PAYMENT TERMS Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect orprepaid with the charges added to the invoice.All shipments are F.O.B. point of origin.Multiquip’s responsibi...
Page 49 - NOTE PAGE
MT75HS RAMMER — OPERATION AND PARTS MANUAL — REV. #11 (01/12/12) — PAGE 49 NOTE PAGE NOTES
Page 50 - OPERATION AND PARTS MANUAL; Your Local Dealer is:; HERE’S HOW TO GET HELP; PLEASE HAVE THE MODEL AND SERIAL; CANADA
OPERATION AND PARTS MANUAL Your Local Dealer is: HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office MQ Parts Department 18910 Wi lm i ngton A v e . C ars on, C A 90746 Cont a ct : mq@mult i qu i p.com T e l. (800) 421-1244 F a ...
