Msd 2960 Atomic LS7 Master Kit Installation- User Manual
Msd 2960 Atomic LS7 Master Kit Installation– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CAPABILITIES; Po w e r M o d u l e : The Power Module of the Atomic LS7 is the
- Page 3 – Figure 1; PREPARING THE FUEL RAILS FOR IN-
- Page 4 – FUEL RAIL INSTALLATION; Figure 5
- Page 5 – FRONT; STOP HERE
- Page 6 – FUEL RAIL/ECU WIRING; Alternator: The kit plugs directly into the factory GM alternator.
- Page 8 – DRIVER; Figure 15 Wiring
- Page 9 – POWER MODULE INSTALLATION; N o t e : T h e Po w e r M o d u l e; L S; Figure 17 Power Module Wiring Diagram.
- Page 10 – FUEL SYSTEM REQUIREMENTS; Power Module; Battery 1, Connect to Positive Battery terminal.; CONNECTOR; This wire functions as a Malfunction Indicator
- Page 11 – FUEL SYSTEM INSTALLATION; Figure 19 Installing Fuel Hose to the Push-Lock Fittings.; severe damage to your engine and/or fuel system.; FUEL INLET FITTINGS AND CROSS-OVER LINE; Due to the variety of intake manifolds and
- Page 12 – WARNING: MSD’s Push-Lock fittings are designed for; Figure 20 Installing Fuel Hose; Properly Installed Push-Lock Fitting; Improperly Installed Push-Lock Fitting
- Page 13 – WIDE BAND OXYGEN SENSOR INSTALLATION; Figure 23 WBO2 Sensor Location.
- Page 14 – PROGRAMMING; Atomic LS Gauges; MAIN MENU
- Page 15 – INITIAL SETUP PROGRAMMING; Coils
- Page 16 – Rev Limit
- Page 17 – ADVANCED SETUP; Fans: This setting sets the temperatures to activate two electric; TPS Enrichment
- Page 18 – MAP Enrichment: To assist in manifold pressure transitions; Racepak Dash Option
- Page 19 – HANDHELD DISPLAY OPTIONS; Display Setup: The display Setup controls the look; Figure 29 Monitor Display Selections
- Page 20 – DIAGNOSTICS; CODE NAME
- Page 21 – CLEAR FLOOD
- Page 22 – TECH NOTES
- Page 24 – INSTALLATION INSTRUCTIONS; Limited Warranty; or consequential damages.; Service; When returning MSD components for warranty service,; Proof of Purchase must be supplied for verification. After; All returns must have a Return Material Authorization (RMA) number; issued to them before; M S D; Created
M S D
•
W W W . A T O M I C E F I . C O M
• ( 9 1 5 ) 8 5 5 - 7 1 2 3 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product
will help if there is ever a warranty issue with your product and helps the MSD R&D team create
new products that you ask for! Go to www.msdperformance.com/registration.
Atomic LS7 EFI Master Kit
PN 2960
1 - TPS Sensor Harness
4 - Grommets, Sleeves, and
Mounting Screws
4 - Fuel Rail Brackets
8 - Injector Retainer Clips
1 - Spacer
1 - Shim Kit
8 - 6mm x 12mm Screws
8 - 8/32” Socket Head Cap
Screws
4 - M6 x 100mm Intake Bolts
4 - 6mm x 16mm Hex Head
Bolts
Parts Included:
2 - Fuel Rail Assemblies
1 - Power Module
1 - Handheld Monitor
1 - Wideband O2 Sensor
1 - Weld - in O2 Sensor Bung,
Plug, and Crush Washer
1 - CAN Cable
1 - 4x Cam Sensor Harness
1 - 58x Crank Sensor Harness
2 - MAP Sensor Harnesses
4 - Injector Harnesses
1 - IAT Sensor and Grommet
1 - 4GB Micro SD Card
Not legal for use on pollution controlled vehicles: The MSD Atomic EFI system is not CARB
approved for use on emission controlled vehicles.
Installation of this product requires detailed knowledge of automotive systems
and repair procedures. Installation of fuel system parts and any fuel tank
modifications must be carried out by a qualified automotive technician. Installation of fuel system
parts requires handling of gasoline. Ensure that work is performed in a well ventilated area with an
approved fire extinguisher nearby. Extinguish all open flames, prohibit smoking and eliminate all
sources of ignition in the area of the vehicle before beginning the installation. When working with
fuel systems, eye goggles and other safety apparel should be worn to protect against debris and
sprayed gasoline. The finished work must be thoroughly checked to ensure there are no fuel leaks.
DANGER
CAUTION
WARNING
NOTICE
4 - #12 Washers
2 - 90º -6AN Fittings
1 - 15” High Pressure Fuel Hose
Parts Required, Not Included:
Fuel System: Fuel Pump, Fuel
Filter, Injectors, Injector
O-Rings,
Regulator, and Fuel Line.
Thread sealer for intake bolts.
Thank you for selecting the Atomic LS EFI System! MSD’s Atomic EFI systems are designed with two
major goals; to simplify installation of EFI and deliver better overall performance from your engine.
Simplicity is achieved through wired-less technology to ease installation plus the Atomic is simple
to program with no PC required! Performance is delivered through advanced control of the fuel and
ignition, just as you’d expect from MSD.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 INSTALLATION INSTRUCTIONS M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 5 - 7 1 2 3 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 CAPABILITIES The Atomic LS7 kit is designed to fit the original equipment intakes. The Atomic LS7 kit is a self integrated Fuel and Ignition c...
INSTALLATION INSTRUCTIONS 3 M S D • W W W . A T O M I C E F I . C O M • ( 9 1 5 ) 8 5 5 - 7 1 2 3 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 FUEL RAIL FUEL RAIL COVER LIFT THIS SIDE OF COVER ENOUGH TO CLEAR FUEL RAIL FUEL RAIL FUEL RAIL COVER PUSH COVER FUEL RAIL FUEL RAIL COVER LIFT COVER UP...
4 INSTALLATION INSTRUCTIONS M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 5 - 7 1 2 3 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 7. Plug the FPS connector into the fuel pressure sensor under the fuel rail (Figure 5). 8. Connect the CAN cable from one rail to the other (F...
