Msd 5096 DynaForce Starter, GM LS1-LS7 Engines Install- User Manual
Msd 5096 DynaForce Starter, GM LS1-LS7 Engines Install– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – • If there is not enough clearance, you will need; Figure 4 Checking Gear Mesh.; Figure 2 Checking Pinion Clearance.
- Page 3 – Figure 5 Wiring the Starter.; TECH NOTES; INSTALLATION INFO; NOISE; exceeds your starting and electrical system requirements.
- Page 4 – Limited Warranty; or consequential damages.; Service; When returning MSD components for warranty service,; Proof of Purchase must be supplied for verification. After; All returns must have a Return Material Authorization (RMA) number; issued to them before; M S D
1. Make sure the starter mounting flange on the engine block is clean and smooth.
2. Install the starter with the supplied hardware. It is recommended to leave the shims out until pinion
gear to ring gear teeth is checked. Torque the bolts to 32 lb-ft.
Note: The supplied bolts must be used for proper installation.
3. Check that the position of the solenoid is away from direct heat sources and other components. If there
are clearance problems, the starter housing can be rotated to move the location of the solenoid. This is
done by removing the three bolts on the mounting block and repositioning the starter motor (Figure 1).
MSD DynaForce Starter
Chevrolet LS Series
PN 5096
WARNING: Before installing the DynaForce Starter disconnect the battery cables. When discon-
necting the battery cables, always remove the Negative (-) cable first and install it last.
IMPORTANT: Proper installation of the DynaForce Starter is important to the overall operation. Correct align-
ment of the starter pinion with the ring gear is needed to achieve the best operation and longev-
ity from your starter. Please read the instructions before attempting the installation.
Figure 1 Clocking the Starter for Clearance.
CLOCKING
LOCATIONS
M S D
• W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered in our
monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if there
is ever a warranty issue with your product and helps the MSD R&D team create new products that you
ask for! Go to www.msdperformance.com/registration.
Parts Included:
1 - Starter
2 - Mounting Bolts
1 - Shim Kit
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 INSTALLATION INSTRUCTIONS M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 4. With the starter installed, check the clearance between the ring gear and the edge of the pinion gear (Figure 2). There should be at leas...
INSTALLATION INSTRUCTIONS 3 M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Figure 5 Wiring the Starter. 12-GAUGE MINIMUM TO IGNITION SWITCH TECH NOTES ________________________________________________________________...
TECH NOTES _________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________ _____________________________________________...
