Mitsubishi Electric MSZAP42VGDKIT - User Manual

En-4 Operation indicator lamp Remote control receiving section Emergency operation switch Page 11 Horizontal vane Air inlet Air fi lter Air cleaning fi lter (Anti-Allergy Enzyme fi lter) (Electrostatic anti-allergy enzyme fi lter, option) Front panel N AME OF EACH PART Indoor unit Remote controller Sign...

En-5 ● OPERATING INSTRUCTIONS ● Before operation: Insert the power supply plug into the power outlet and/or turn the breaker on. Installing the remote controller batteries 1. Remove the front lid. 2. Insert the negative pole of AAA alkaline batteries fi rst. 3. Install the front lid. 4. Press RESET. ...

En-6 AUTO mode (Auto change over) The unit selects the operation mode according to the difference between the room temperature and the set temperature. During AUTO mode, the unit changes mode (COOL↔HEAT) when the room temperature is about 2°C away from the set temperature for more than 15 minutes. N...

En-7 ● OPERATING INSTRUCTIONS ● Press to select fan speed. Each press changes fan speed in the following order: • Two short beeps are heard from the indoor unit when set to AUTO.• Use higher fan speed to cool/heat the room quicker. It is recommended to lower the fan speed once the room is cool/warm....

En-8 I- SAVE OPERATION 1 Press during COOL, ECONO COOL, HEAT mode or NIGHT MODE to select i-save mode. 2 Set the temperature, fan speed, and airfl ow direction. • The same setting is selected from the next time by simply pressing . • Two settings can be saved. (One for COOL, ECONO COOL, one for HEAT)...

En-9 ● OPERATING INSTRUCTIONS ● N IGHT MODE OPERATION Press during operation to activate NIGHT MODE. • The operation indicator lamp dims. • The beep sound will be disabled except that emitted when the opera- tion is started or stopped. • Noise level of the outdoor unit will be lower than that mentio...

En-10 W EEKLY TIMER OPERATION • A maximum of 4 ON or OFF timers can be set for individual days of the week. • A maximum of 28 ON or OFF timers can be set for a week. Setting the weekly timer * Make sure that the current time and day are set correctly. 1 Press to enter the weekly timer setting mode. ...

En-11 ● OPERATING INSTRUCTIONS ● Operation indicator lamp When the remote controller cannot be used... Emergency operation can be activated by pressing the emergency operation switch (E.O.SW) on the indoor unit. Each time the E.O.SW is pressed, the operation changes in the following order: If a powe...

En-12 1. Lift the front panel until a “click” is heard.2. Hold the hinges and pull to remove as shown in the illustration above. • Wipe with a soft dry cloth or rinse it with water. • Do not soak it in water for more than two hours. • Dry it well in shade before installing it. 3. Install the front p...

En-13 ● OPERATING INSTRUCTIONS ● W i-Fi INTERFACE SETTING UP (VGK TYPE ONLY) This Wi-Fi interface, communicates the status information and controls the commands from the server by connecting to the indoor unit. Wi-Fi interface Wi-Fi interface Front panel Front panel Wi-Fi interface introduction RESE...

En-14 9 10 3 4 5 6 7 8 When WPS-Push is enabled on the Wi-Fi interface, MODE LED starts fl ashing orange (every second). Open Wi-Fi Control App. Enter MAC and ID into ‘Add new unit’ and select ‘Add’. Once completed, control your heat pump via Wi-Fi. 7 W i-Fi INTERFACE SETTING UP (VGK TYPE ONLY) RESET...

En-15 ● OPERATING INSTRUCTIONS ● Description ERR (Orange) NET (Green) MODE (Orange) UNIT (Green) Connection to server established, and connection to indoor unit failedConnection to Router failed, and connection to indoor unit established (*3) Connection to Router failed, and starting up indoor unit ...

En-16 Even if these items are checked, when the unit does not recover from the trouble, stop using the air conditioner and consult your dealer. Symptom Explanation & Check points Indoor Unit The unit cannot be operated. • Is the breaker turned on? • Is the power supply plug connected? • Is the O...

En-17 ● OPERATING INSTRUCTIONS ● In the following cases, stop using the air conditioner and consult your dealer. • When water leaks or drips from the indoor unit. • When the operation indicator lamp blinks. • When the breaker trips frequently. • The remote control signal is not received in a room wh...

En-18 S PECIFICATIONS Wi-Fi interface Model MAC-568IFB3-E Input Voltage DC12.7 V (from indoor unit) Power consumption MAX 2 W Size H×W×D (mm) 79×44×18.5 Weight (g) 60 (including cable) Transmitter power level (MAX) 17.5 dBm @IEEE 802.11b RF channel 1ch ~ 13ch (2412~2472 MHz) Radio protocol IEEE 802....