Milwaukee 5337-20 - User Manual

Milwaukee 5337-20

Milwaukee 5337-20 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
Page: / 23

Table of Contents:

  • Page 2 – INSTRUCTIONS; – Forcing discs; Disassembly
  • Page 3 – Drive out nose piece latch bar with 3/8”
  • Page 4 – Tap spline area of spindle assembly, do
  • Page 7 – If armature fan requires removal, use; The chisel hammer does not have a
  • Page 8 – The exposed plane surface serves only
  • Page 9 – Should the field be stuck, tap the motor
  • Page 10 – Maintenance; OR
  • Page 11 – Re
  • Page 13 – Sequence and torques of the screws:
  • Page 14 – Assembly; Install the following parts:
  • Page 15 – The static slip of the clutch is pre-set. If
  • Page 16 – See illustration below:
  • Page 17 – Apply Blue loctite
  • Page 18 – Lubricate front of gear box per lubrica-
  • Page 20 – engage into the spindle groove!
  • Page 21 – The six screws must be tightened
  • Page 22 – Apply Blue Loctite
Loading the manual

58-92-5300 d3

REPAIR

INSTRUCTIONS

032005

Cat. No. 5337-20

3/4” Hex Demolition Hammer

Cat. No. 5340-20

2” Spline Rotary Hammer

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 W. LISBON ROAD • BROOKFIELD, WISCONSIN 53005-2550

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Other Manuals for Milwaukee 5337-20

Summary

Page 2 - INSTRUCTIONS; – Forcing discs; Disassembly

2 PAGE 58-92-5300 d3 INSTRUCTIONS REPAIR SpecialTools Require – Forcing discs 61-10-0011 – Hex key 4 mm – Hex key 5 mm – Sleeve 61-10-0013 – Pin-type face spanner 61-10-0012 – Disassembly Removing the auxiliary handle 1 Remove handle (1) by turning it counter-clockwise. Disassembling the handle 1 Un...

Page 3 - Drive out nose piece latch bar with 3/8”

3 PAGE 58-92-5300 d3 INSTRUCTIONS REPAIR Removing the spring ring 1 Remove both retainers (1). 2 Slightly spread spring ring (2) and pull it off the machine towards the front. Removing the nose piece as-sembly 1 Remove four screws (4) with an 6mm hex key and remove nose piece assembly (1) 2 Remove r...

Page 4 - Tap spline area of spindle assembly, do

4 PAGE 58-92-5300 d3 INSTRUCTIONS REPAIR Combined drill/chisel hammer: Removingthe spindle 1 Drive out the complete spindle assembly with light taps on rear spindle spline end (1) with a plastic face hammer. ☞ Tap spline area of spindle assembly, do not strike piston assembly. Chisel hammer: Removin...

Other Milwaukee Models