Miele T4859Ci SUPERTRONIC - Manual

~ The tumble dryer can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience orknowledge, if they are are supervised whilst using it or have beenshown how to use it in a safe way and understand the hazardsinvolved. Safety with children ~ Children under 8...

Technical safety ~ Before setting up the tumble dryer, check it for any externally visible damage.Do not install or use a damaged tumble dryer. ~ Before connecting the tumble dryer, ensure that the connection data on the data plate (voltage and frequency) match the mainselectricity supply. If in any...

Correct use ~ To prevent the risk of fire, the following textiles must not be dried in this appliance: – items which have not been washed. – items, such as workwear, which have not been thoroughly cleaned and which are still soiled with grease, oil or otherdeposits (such as cosmetics, lotions etc).I...

Accessories ~ Only use genuine Miele original spare parts and accessories with this tumble dryer.If non-Miele parts are used, guarantee, performance and productliability claims may be invalidated. Miele cannot be held liable for damage caused bynon-compliance with these Warning and Safety instructio...

Control panel a Miele { home Symbol for Miele | home enabled appliance b Information sensor : The sensor lights up wheninformation about the menu in thedisplay is available. c Service interface This is used by service techniciansto run diagnostic checks on yourmachine, or to update programmingdata i...

Selector sensors The selector sensors are on the left and right of the display.They light up when they are active. The selector sensors areused for the following: Selecting an option A dot ( # ) next to an option indicates that it can be selected. The selector sensor on the left is active when the d...

Structure of the main menu Favourite programmes – Favourite programmes (listed alphabetically) – Create – Change – Delete Cottons – Minimum iron – Delicates – .... – Drying level: (depending on programme) – .... – Duration(depending on programme) – Extras (depending on programme) – Start at – Finish...

Settings ! – Language ! – Time* – Drying levels* – Extended cool down – Airways indicator – Code – Buzzer – Keypad tone – Brightness – Contrast – Display / keypad illumination – Memory – Anti-crease – Miele | home** – Remote control** * This option has further sub-menus. ** Appears if the dryer has ...

This appliance is communicationenabled and can be linked into theMiele | home system via a communication module b (optional accessory). Miele | home enabled appliances send information via the household powersupply network d to the master appliance c / e about the operational status of the appliance...

Before using the dryer for the first time ensure that it iscorrectly installed and connected. See "Installation andconnection". Preparing the dryer for use is done in five stages. The dryerguides you automatically through steps 1. to 5. 1. Welcome screen ^ Switch the dryer on with the K butt...

3. Set the time of day (if required) Enter the time of day. Time [ [ [ + $ 10 :21 – # OK ! ^ Use + and - to set the hour. ^ Confirm with OK . Then set the minutes and confirm with OK . 4. Miele | home message This communication enabled dryer can transmit programmedata through the power lines to the ...

Garment care label symbols Drying q Normal/higher temperature r Reduced temperature:Select Low temperature (for delicate textiles) s Do not tumble dry Ironing I Very hot H Hot G Warm J Do not iron Tips on drying – Always observe the maximum recommended loads given in the"Programme chart". Ne...

Prepare the laundry To ensure an even drying result sort thewashed laundry according to: . . . . . the drying level required,. . . the type of fibre or weave,. . . size,. . . the moisture content after spinning. , Make sure that objects, e.g. detergent dispensing balls, havebeen removed from the lau...

Switch the dryer on with the K button \ \ \ Main menu 10:21 [ [ $ Favourite programmes # Cottons ! Minimum iron m ^ Select the programme you want: Use the right handsensors to show more programmes. An additional menu may appear depending on programme selected: – Programmes with drying levels e.g. Co...

– Programmes which operate by time e.g. Warm air ... : You have to select a duration. \ \ \ Warm air 1-6 kg 0:15 h 10:21 [ [ [ $ Duration 0:25 h:min + $ # Extras – # # Start at OK ! ^ Touch the Duration sensor. ^ Use the + and - sensors on the right to alter the value highlighted. ^ Confirm the valu...

Select Extras \ \ Extras 10:21 [ $ 8 Short # 9 Low temperature OK ! ^ Select the Extra you require. A tick 9 will appear to show which Extra has been selected. ^ Confirm with OK . Start at / Finish at You can set the start (Start at) or the end (Finish at) time ofa programme. The start and end time ...

Starting a programme ^ Touch the green illuminated Start sensor. In order to start the programme you must place your fingerin the centre of the Start sensor when touching it. If the programme does not start: wait for 4 seconds andtouch the Start sensor in the middle again. G Cottons 10:21 [ Normal -...

Cancelling a programme ^ Touch the U sensor. \ Cottons 10:21 [ : Cancel programme? ! Continue: Cancel ! ^ Select Cancel . The items will be cooled down 7 , depending on the temperature reached and how long they have been driedfor. If you select U and Cancel , O Finish will appear in the display. ^ P...

Before the end of a programme There is a cooling down phase at theend of the drying sequence: 7 "Cooling down" appears in the display.The programme is not finished until thecooling down phase has beencompleted. Programme end - unload the drum O Anti-crease and Finish will appear in the displ...

Short For drying fabrics which can withstandhigher temperatures and have q on the care label. Do not use on minimum ironor delicate fabrics. – This option uses a higher temperature for a shorter drying time. Low temperature Delicate and minimum iron fabrics withthe r symbol on the care label (e.g. a...

You can save up to ten programmes with the settings youhave selected for them under names of your choice. Thename can have up to 12 characters. The favourite programmes which have been set are storedalphabetically. To save a favourite programme There are two ways of saving a programme as a favourite...

To save a name for a favourite programme \ \ \ Name: D r y _ _ _ _ _ _ _ 10:21 [ [ [ $ Space Delete character $ ) g h i j k l m n o p q r s t u v w x y * ! Select character Confirm name ! ^ Select Confirm name . To select a favourite programme ^ Call up the Favorite programmes menu. The saved progra...

Cottons Max. load 6 kg* Extra dry, Normal+, Normal** Use for Single and multi-layered cotton fabrics such as towelling, T-shirts,underwear, flannelette bed linen and baby clothes. Tip – Select Extra dry for multi-layered and very thick fabrics. – Do not use Extra dry for loopknit fabrics (e.g. T-shi...

Hygiene programmes In the Hygiene programmes the temperature is held constant for a longer period of time to deactivate micro-organisms, e.g. bacteria or house dustmites, and alsoto reduce the number of allergens in the laundry. These programmes should not be interrupted as this would prevent themic...

Emptying the condensed watercontainer The condensed water will be collectedin the condensed water containerunless the appliance has been set upto drain via the drain hose (seeinstallation). Empty the condensed watercontainer after every dryingprogramme. The drying programme will beinterrupted if the...

Cleaning the fluff filters The fluff which is created by the dryingprocess is collected by the fluff filters inthe door and the door opening. Cleanthe filters after each drying programme*. Cleaning them whilst dry Tip: You can also use a vacuumcleaner to remove the fluff. ^ Open the door and pull th...

Cleaning them with water If there is a great deal of compactedfluff on any of the filters, they can beremoved and cleaned under hotrunning water. ^ Open the door and pull the fluff filterout of the door as describedpreviously. The two filters in the door opening canalso be removed if you need to cle...

Cleaning the tumble dryer Disconnect the tumble dryer fromthe mains electricity supply. Miele branded cleaning andconditioning products are available toorder via the internet onwww.miele-shop.com. ^ Clean the housing and control panelwith a slightly damp cloth and a milddetergent or soapy water. ^ T...

Cleaning the condenser unit Detergent residue, hair and fine flufffrom the dryer can get through the flufffilters and block the condenser unit.Dust from the room in which the dryer isinstalled can also get into thecondenser unit and cause a blockage. Check the condenser unit at least once a year. Al...

^ Pull the condenser unit out of itshousing by the handle. Checking the condenser unit ^ Hold the condenser unit up to thelight as shown . ^ Check to see if there is any fluffinside it.The arrows in the illustration aboveindicate where to look. If you cannot see any fluff: ^ Replace the condenser un...

^ Then flush the unit through from thefront. ^ Check the condenser unit again forany visible fluff and if necessary flushit through again until it has all gone. ^ Repeat as required. ^ Also make sure the rubber seals areclean.The rubber seals must not beremoved and must be free of kinks. ^ Shake the...

With the help of the following notes minor faults in the performance of theappliance, some of which may result from incorrect operation, can be put rightwithout contacting the Service Department. , Repair work to electrical appliances should only be carried out by a suitably qualified person in stri...

An unsatisfactory drying result Problem Possible cause Remedy The laundry is notsufficiently dry. The load consisted ofdifferent fabrics. – Finish drying using the Warm air programme. – Select a different programme next time*. Feather filled pillowssmell after drying. Feathers are a naturalproduct a...

Other problems Problem Possible cause Remedy The dryingprocess goes ontoo long or evenswitches off. The request to clean theairways may appear in thedisplay. Please check all the possiblecauses and switch the dryer offand then back on again. Ventilation to and from thedryer may be insufficient,e.g. ...

Problem Possible cause Remedy Water leaks from thedryer after thecondenser unit hasbeen cleaned. – The inner cover of the condenser unithas not been lockedproperly and/or thecondenser unit hasnot been positionedcorrectly. – Fluff has collected in the condenser unithousing. – Ensure that the condense...

Changing the lamp Disconnect the tumble dryer fromthe mains electricity supply. ^ Open the door. You will find the interior light cover atthe top of the drum aperture. ^ Insert a suitable tool, such as a widebladed screwdriver, under the sideedge of the light cover as illustrated. ^ Apply a little p...

Repairs In the event of any faults which youcannot remedy yourself, please contact – your Miele dealer or – the Miele Service Department (see back cover for contact details). When contacting your dealer or theService Department, please quote themodel and serial number of yourappliance, both of which...

Front view a Mains connection cable b Condensed water container c Control panel d Door (can be fitted with a decorpanel) e Service panel for condenser unit f Hose for external drainage ofcondensed water(see "External condensed wateroutlet") g Rear view: Slot for Miele | home communication mo...

Installation site , Make sure the dryer door can be opened without hindrance afterinstallation. Building under a continous worktop /in a kitchen run This tumble dryer is specially designedfor installation under a continuousworktop run in a fitted kitchen. N = Niche height (820-930 mm) When moving th...

Levelling the appliance ^ Turn the 4 screw feet to adjust thedryer to the correct height and level. Longer screw feet are available asan optional accessory. Unscrew andremove the feet supplied with theappliance before fitting the longerscrew feet. The cover plate on the dryer mustbe aligned horizont...

Matching the fascia panel tothe height of adjacent drawerfronts The fascia panel can be aligned withthe drawer fronts by adjusting thespacer bars. ^ Using a socket spanner, turnclockwise or anti-clockwise until therequired height is reached. If necessary individual bars can beremoved or more added. ...

Fitting the front panel The appliance front can be fitted with adoor panel to match other kitchen units. If fitted in a Miele kitchen, the doorpanel can be ordered pre-drilled withthe necessary fixing holes. If fitted in a non-Miele kitchen, asuitable panel will have to be drilledto suit by a qualif...

Fitting a door front panel madeby another manufacturer Preparing the front panel A Measure distance X for drilling the hinge holes. – with spacer bars: – without spacer bars: (the front panel must becorrespondingly higher) B Mark the two hinge holes and thefour smaller holes as shown in thediagram. ...

For right hand hinging only: – front panel shown decor side face down, upper edge at the bottom: if width ( b ) increases, measurement a must also be increased b = 592 mm N a = 21.5 mm b = 593 mm N a = 22.0 mm b = 594 mm N a = 22.5 mm b = 595 mm N a = 23.0 mm b = 596 mm N a = 23.5 mm H = height of a...

Fitting a plinth facing The gap between the lower edge of thetumble dryer plinth and the floor can beclosed up using a suitable kitchenfurniture plinth facing. The tumble dryer plinth has a specialgroove in which a plinth facing can befitted. Plinth facing dimensions Length: 592 - 596 mm Thickness: ...

Electrical connection U.K. All electrical work should be carried outby a suitably qualified and competentperson, in strict accordance withcurrent national and local safetyregulations (BS 7671 in the UK). Ensure power is not supplied to theappliance until after installation workhas been carried out. ...

Load 1 Final spin speed in a domestic washing machine Residual moisture Energy Duration kg rpm % kWh min. Cottons Normal 2 6.06.0 10001000 6060 3,582,00 9959 Cottons Normal 6.06.06.06.0 1200140016001800 53504443 3,253,102,752,70 91867877 Cottons Normal+ Short+ Low temperature 6.06.0 10001000 6060 3,...

Height 820 mm Width 595 mm Depth 575 mm Suitable for stacking Yes Weight 54 kg Drum volume 100 litres Maximum capacity 6 kg dry weight Capacity of condensed water container approx. 3.5 litres Drain hose length 950 mm Maximum delivery head 1.5 m Maximum drain hose length 4 m Length of connection cabl...

The Settings menu is used to alter the dryer's electronics tosuit different requirements.Settings can be altered at any time. Open the Settings menu \ \ \ Main menu 10:21 [ [ $ Settings ! # Favourite programmes # Cottons m ^ Use the top right hand sensor to select the Settings ! menu. ^ Confirm with...

Time The time can be set to appear as a 24 hour or 12 hourclock. You can also use this setting to adjust the time ofday. Clock format \ \ Time 10:21 [ $ 24 h clock ( # 12 h clock OK ! ^ Select the format you want. The dryer is delivered with the clock format set as a 24 hourclock. Set the time of da...

Extended cool down The cooling down phase which takesplace before the end of a programmecan be lengthened by 2, 4, 6 ... up to18 minutes if required. This helpstextiles cool down more intensely. The programme duration increases in 2minute increments. Extended cooling down can only beselected for pro...

Code The code prevents the dryer being used without yourknowledge. When the code has been activated, you have to enter a codeafter switching the dryer on. Otherwise the dryer cannot beoperated. The door can be opened and items removed at any time. To activate the code The display will now request th...

Buzzer When the buzzer function has beenactivated, an audible tone sounds atthe end of a programme. Off Factory default The buzzer is switched off but soundsat maximum volume if there is a fault. Normal The buzzer sounds at the end of aprogramme. Loud The buzzer sounds louder at the end ofa programm...

Memory The electronics will memorise thedrying level and some of the extraoptions selected for the currentdrying programme and the durationof a timed drying programme. When the programme is chosen againthese settings will appear in thedisplay. Off Factory default On Anti-crease Anti-crease helps pre...