Miele PWM 508 Mop Star 80 [EL DP] - User Manual

Caring for the environment 6 Disposing of the packaging ma-terial The packaging material is used for hand-ling and protects the appliance fromtransport damage. The packaging ma-terial used is selected from materialswhich are environmentally friendly fordisposal and can generally be recycled.Recyclin...

Warning and safety instructions 7 This washing machine complies with all current local and nationalsafety requirements. However, inappropriate use can lead to per-sonal injury and damage to property.Read the operating instructions carefully before using the washingmachine. They contain important inf...

Warning and safety instructions 8  Children over the age of 8 may only use the washing machine without supervision if its operation has been clearly explained tothem and they are able to use it safely. Children must be able to un-derstand and recognise the possible dangers caused by incorrect op-er...

Warning and safety instructions 10  Temporary or permanent operation on an autonomous power sup- ply system or a power supply system that is not synchronised withthe mains power supply (e.g. island networks, backup systems) ispossible. A prerequisite for operation is that the power supply systemcom...

Warning and safety instructions 12  When adding or removing laundry during the main wash, your skin may come into contact with detergent, particularly if the detergent isdispensed externally. Take care when placing your hands inside thedrum. If suds have come into contact with the skin, rinse off i...

Operating the washing machine 13 Control panel a Language sensor control    For selecting the current user lan-guage.The system language is displayedagain at the end of the programme. b Touch display with sensor controls Displays the selected programme.The programme settings are selectedusing the s...

Operating the washing machine 14 Symbols on the control panel Right side:  Mops  Mops plus  Mops thermal disinfection  Mops chemo-thermal disinfection PRO Cottons PRO Left side:  Cloths  Cloths plus  Cloths thermal disinfection  Cloths chemo-thermal disinfection  Pads  Further programmes

Operating the washing machine 15 Symbols in the display  Temperature : use the Temperature  sensor control to set the temperature of the wash programme.  Spin speed : use the Spin speed  sensor control to set the spin speed of the wash programme.  Extras : use the Extras  sensor control to add Ex...

Operating the washing machine 16 Sensor controls and touch dis-play with sensor controls The sensor controls  ,  and Start/Stop and the sensor controls in the display respond to finger tip contact.Every touch of a sensor is confirmedwith an audible tone. You can adjust thevolume of the keypad tone...

Operating the washing machine 17 Examples of how to operate theappliance Option lists The   and    arrows on the right of the display indicate that choices are avail-able.  Language   deutsch čeština english (AU) dansk The list scrolls down when the   sensor is touched. The list scrolls up whe...

Before using for the first time 18  Damage resulting from incorrect installation and connection.Installing and connecting the wash-ing machine incorrectly will causeserious property damage.See “Installation”. Emptying the drum A swivel elbow for the drain hose and/orassembly material may be stored ...

Before using for the first time 19 Setting the display brightness Brightness –  70 OK + %  Set the brightness you want with the – and + sensors and confirm your se- lection with the OK  sensor. The display will change to the next set-ting. Reference to external appli-ances A reference to external ...

Before using for the first time 20 Selecting programme packages  Programme packages   Standard Pre-treatmops    Touch the   or    sensor control until the programme package you want ap-pears in the display.  Touch the programme package sensorcontrol. The display shows the associated pro-gra...

Before using for the first time 21 Setting up a payment system If you wish to set up a payment system,read “Payment system” under “Super-visor level”.If you do not wish to set up a paymentsystem, you can skip this stage.  Payment system   No paymentsystem Programmecontrol  Touch the No payment s...

1. Preparing the laundry 23  Damage due to foreign objects. Nails, coins, paper clips, and so oncan cause damage to textiles andcomponents in the machine.Check the mops or the laundry be-fore washing and remove any foreignobjects.  Damage due to solvent-based detergents.Cleaning agents containing ...

2. Loading the washing machine 24 Opening the door  Reach under the door grip and pullthe door open. Check the drum for foreign objectsbefore loading it with laundry.  Load the mops, cleaning cloths orpads loosely in the drum.  Unfold the laundry and load looselyinto the drum. Mixing both large a...

3. Selecting a programme 25 Switching on the washing ma-chine  Press the   control. Selecting a programme Selecting standard programmes withthe programme selector dial  Turn the programme selector to therequired programme. The selected programme will be shownin the display. The display will thenc...

4. Selecting programme settings 26 Selecting the temperature You can alter the preset temperature ofcertain programmes.  Touch the Temperature     sensor. The following will appear in the display:  Temp. 40°C 60°C 30°C  Select the desired temperature. The selected temperature is markedwith a fra...

5. Adding detergent 27 There are several options for adding de-tergent to the washing machine. Detergent drawer You can use any detergent that is suit-able for washing machines. Detergent dispensing Please follow the detergent manufac-turer's instructions in relation to dosage. Adding too much deter...

5. Adding detergent 28 Adding fabric conditioner or liquidstarch separately  Select the Separate rinse programme.  Change the spin speed if necessary.  Add fabric conditioner or liquid starchto the  compartment. Do not ex- ceed the maximum level mark.  Touch the Start/Stop sensor. It will be au...

6. Starting the programme – the end of the programme 29 Starting the programme The programme can be started as soonas the Start/Stop  sensor is flashing on and off.  Touch the Start/Stop  sensor. The door will lock (   symbol) and the programme will start. If a delay start period has been selec-te...

Delay start 30 The Delay start function can be used toset the time until the programme startsor the programme finish time (see“Delay start” under “Supervisor level”). Selecting the Delay start func-tion  Touch the Further choices     sensor control.  Select the Finish at    , Start at    or Sta...

Programme chart 31 Mop programmes - A pre-spin* and a pre-rinse cycle are carried out before the main wash.    Mops  60 °C Max. load 8.0 kg Items Cotton, mixed fibre or microfibre mops Tip Use specialist detergents. 1400 rpm Extras: 2nd Pre-rinse   , Microfibre   Rinses: 2–5*    Mops plus 40 °C ...

Programme chart 32 Cleaning cloth programmes - A pre-rinse cycle is carried out before the main wash.    Cloths 60 °C Max. load 4.0 kg Items Cotton, mixed fibre or microfibre cloths Tip Use specialist detergents. 1400 rpm Extras: Pre-wash   Rinses: 2–5*    Cloths plus 40 °C to 90 °C Max. load 4.0...

Programme chart 33 Cottons PRO   60 °C Max. load 8.0 kg Items Mixed fibre textiles (50 % cotton and 50 % polyester) Tip - Extra energy-efficient wash programme for commercial cotton or cotton/synthetic blend textiles with normal levels of soiling, e.g.workwear. 1400 rpm Extras: Pre-wash   Rinses: 2...

Programme chart 34 Curtains cold to 40 °C Max. load 3.0 kg Items Curtains specified as machine-washable by the manufacturer Tip - A pre-rinse cycle is carried out before the main wash. - For curtains which crease easily, deselect the spin speed func- tion. 600 rpm Extras: Pre-wash   Rinses: 3 Separ...

Programme chart 35 Pre-treat mops (ready to use) - Mops are washed and pre-treated in one cycle.- A pre-spin* and a pre-wash cycle are carried out before the main wash.- There is no water intake via the fabric conditioner compartment during the disin- fecting process. Mops +rtu 60 °C Max. load 8.0 k...

Programme chart 36 Pre-treat cloths (ready to use) - Cleaning cloths are washed and pre-treated in one cycle.- A pre-wash cycle is carried out before the main wash.- There is no water intake via the fabric conditioner compartment during the disin- fecting process. Cloths + rtu 60 °C Max. load 4.0 kg...

Programme chart 37 Ready to use - The residual moisture after pre-treatment is selected with the   sensor control. Mops + rtu   40 °C to 90 °C Max. load 8.0 kg Items Cotton, mixed fibre or microfibre mops Tip - Mops are washed and finished in one cycle. - A pre-spin* and a pre-rinse cycle are carr...

Programme chart 38 Workwear Oil/fat special 60 °C to 90 °C Max. load 8.0 kg Items Work coats, jackets, hats, cleaning cloths made from cotton ormixed fibres Tip - Activate Pre-wash for heavy contamination. - Use liquid detergent. 1400 rpm Extras: Pre-wash   Rinses: 3 Dust/Flour special 40 °C to 90 ...

Extras 40 You can add Extras to the wash pro-grammes.Not all Extras can be selected withevery programme. If an Extra is not lis-ted, it is not permitted for use with thewash programme in question. Selecting Extras For some programmes, an Extra isoffered directly in the main menu.  Touch the sensor ...

Special features in the programme sequence 41 Spinning Final spin speed When a programme is selected, themaximum spin speed for this wash pro-gramme is shown in the display.You can reduce the final spin speed.However, you cannot select a final spinspeed higher than that shown in thechart. Interim sp...

Changing the programme sequence 42 Changing a programme After the start of a programme, it is nolonger possible to select a different pro-gramme.You will need to cancel the current pro-gramme before you can select a newone. Programme cannot be changed  appears in the display if the programme se-lect...

Changing the programme sequence 43 Adding or removing laundry You can add or remove items during thefirst few minutes after the programmehas started.  Touch the Start/Stop  sensor. The following will appear in the display: Add laundry Cancel programme  Touch the Add laundry  sensor. The programme ...

Cleaning and care 44  Risk of electric shock. Only ever perform cleaning and main-tenance work when the appliance isdisconnected from the power.Disconnect the washing machinefrom the mains electricity supply. Cleaning the drain filter daily Coarse dirt can block the drain filter.Clean the drain fil...

Cleaning and care 45  Turn the impeller by hand to checkthat it can rotate freely.  Remove foreign objects and clean theinterior.  Put the drain filter back in place andsecure it.  Risk of damage from leaking wa- ter.Water will escape from the washingmachine if you forget to replace thedrain fil...

Cleaning and care 46 Cleaning the detergent drawer Washing at low temperatures and theuse of liquid detergent can lead to abuild-up of mould and bacteria in thedetergent drawer.  For hygiene reasons, clean the entiredetergent drawer at regular intervals.  Pull out the detergent drawer untilresista...

Cleaning and care 47 Cleaning the detergent dispenserdrawer compartment  Use a bottle brush to remove deter-gent residues and limescale from thejets inside the detergent drawer.  Replace the detergent drawer. Tip: Leave the detergent drawer slightly open to allow it to dry. Cleaning the drum, suds...

Cleaning and care 48 Cleaning the sealing ring  Check the fold in the sealing ring forforeign objects.  Clean the sealing ring and the innerfold of the sealing ring with a dampcloth. Tip: Leave the door slightly open to al- low the drum to dry. Cleaning the water inlet filters The washing machine ...

Problem solving guide 49 You are able to correct the majority of faults and problems that arise during day-to-day use without external assistance. You can save time and money in many cases,as you do not need to call Miele Service.The following tables are designed to help you to find the cause of a m...

Problem solving guide 50 Programme cancellation and error message Problem Cause and remedy  Drainage fault. Cleandrain filter and pump.Check the drainhose. The drain is blocked or restricted.The drain hose has been fixed too high.  Clean the drain filter and the drain pump.  The maximum drain hei...

Problem solving guide 51 A fault message appears in the display 1) Problem Cause and remedy  Container empty One of the external detergent containers is empty.  Refill the detergent container.  Container 1 empty External detergent container 1 is almost empty.The message can refer to containers 1 ...

Problem solving guide 52 An unsatisfactory wash result Problem Cause and remedy Liquid detergent doesnot give the requiredresult. Liquid detergents usually contain no bleaching agents.They do not remove fruit, coffee, and tea stains.  Use a general purpose powder detergent containinga bleaching age...

Problem solving guide 53 General problems Problem Cause and remedy The machine shakes dur-ing the spin cycle. The machine feet are not level and not secured.  Level the machine and adjust the feet correctly. Large amounts of deter-gent residue remain inthe detergent dispenserdrawer. The water press...

Problem solving guide 54 The door will not open Problem Cause and remedy The door cannot bepulled open during awash programme. The door is locked during the wash programme.  Touch the Start/Stop  sensor control.  Select  Cancel programme or  Add laundry . The door will unlock and you will be able ...

Problem solving guide 55 Opening the door in the eventof a blocked drain outlet and/orpower cut  Risk of electric shock. Only ever perform cleaning and main-tenance work when the appliance isdisconnected from the power.Disconnect the washing machinefrom the mains electricity supply.  Open the acce...

Problem solving guide 56 Cleaning the drain filter Once the flow of water ceases:  Remove the drain filter completely.  Clean the drain filter thoroughly.  Check the drain pump impellers tomake sure they can rotate freely.  Remove any foreign objects (e.g. but-tons, coins, etc.) and clean the in...

Miele Service 57 Contact in case of malfunction In the event of any faults which you can-not remedy yourself, please contactyour Miele Dealer or Miele Service. Contact information for Miele Servicecan be found at the end of this docu-ment. Please quote the model and serial num-ber of your appliance ...

Installation *INSTALLATION* 58 Front view a Double check valves (for UK only) b Inlet hose (cold water) c Inlet hose (hot water) d Electrical connection e Fascia panel f Detergent drawer g Door h Access to drain filter and drain pumpand emergency release i Height-adjustable feet

Installation *INSTALLATION* 59 Rear view a Electrical connection b Interface for communicating with ex-ternal devices c Socket for external dispensing sys-tem d Drain hose (LP version) e Inlet hose (cold water) f Inlet hose (hot water), if fitted g Safety caps for transit bars h Transport clips for ...

Installation *INSTALLATION* 60 Installation locations Side view 1132 850 >1000 714 Washer-dryer stack min. 300 1702 The washing machine can be installedas a washer-dryer stack together with aMiele tumble dryer. This requires aMiele washer-dryer stacking kit whichcan be purchased separately.  Ins...

Installation *INSTALLATION* 61 Transporting the washing ma-chine to its installation site  Danger of injury from incorrect transport.If the washing machine tips up thereis a danger of injury to people anddamage to property.Make sure the washing machine isstable during transportation. Transporting t...

Installation *INSTALLATION* 62 Installation surface A concrete floor is the most suitable in-stallation surface, being far less prone tovibration during the spin cycle thanwooden floorboards or a carpeted sur-face.  The machine must be level and se-curely positioned.  To avoid vibrations during sp...

Installation *INSTALLATION* 63 Removing the right-hand transit bar  Push the cover out and turn thetransit bar 90° using the open span-ner supplied.  Pull out the transit bar. Covering holes  Danger of injury from sharp edges.There is a danger of injury fromreaching into holes that are notcovered...

Installation *INSTALLATION* 64  Risk of damage from incorrect transport.The washing machine may becomedamaged if moved without the transitbars in place.Keep the transit bars in a safe place.Fit them again if the washing ma-chine is to be moved (e.g. when mov-ing house). Fitting the transit bars Ope...

Installation *INSTALLATION* 65  Use a level to check that the washingmachine is standing level.  Hold foot 1 securely with a pipe wrench. Turn counter nut 2 again us- ing the spanner supplied until it sitsfirmly up against the housing.  Risk of damage due to incorrectly aligned washing machine.Th...

Installation *INSTALLATION* 66 Installing the holding bracket  Place the holding bracket on themarking on the plinth.  In the middle of the two outer slottedholes, mark a point for each drill hole.  Drill 2 holes (8 mm) with a depth ofapprox. 55 mm.  Insert the plugs in the holes.  Install the ...

Installation *INSTALLATION* 67 Water connection Cold water connection The washing machine should be con-nected to a mains water supply in ac-cordance with current local and nationalsafety regulations. The German authorit-ies do not require it to have a non-returnvalve as the washing machine has been...

Installation *INSTALLATION* 68 Hot water connection* The hot water temperature must not ex-ceed 70 °C (60 °C in the UK).To minimise energy consumption duringoperation with hot water, the washingmachine should be connected to a suit-able hot water ring circuit. So-called“transmission pipes” (single p...

Installation *INSTALLATION* 69 Electrical connection This description applies to washingmachines both with and without amains plug. The following applies to washing ma-chines with a mains plug: - The washing machine is ready to be connected. - The electrical socket must be easily accessible after in...

Technical data 71 EU Conformity declaration Miele hereby declares that this washing machine complies with Directive 2014/53/EU. The complete text of the EU declaration of conformity is available from one of thefollowing internet addresses: - Products, Download from www.miele.co.uk- For service, info...

Supervisor level 72 The settings menu in the   Super- visor level is locked against unauthor-ised access. The menu can be un-locked with a code. Code-based access Supervisor level is accessed using acode. The code is 000 (factory default). Changing the code You can alter the Supervisor level ac-ces...

Supervisor level 73 Language The display can be set to appear in oneof several different languages. To se-lect the permanent operator languageyou want, go to the Languages sub-menu. When a programme is running, you canchange the user language using the   sensor. Brightness The brightness of the dis...

Supervisor level 74 Anti-crease The Anti-crease function reducescreasing after the end of the pro-gramme. At the end of the programme, the drumcontinues to turn at intervals for up to30 minutes. The washing machine doorcan be opened at any time.Factory default: On Suds cooling Additional water flows...

Supervisor level 75 "Machine" switch-off status The washing machines switches itselfoff automatically. It is switched offafter the end of the programme/Anti-crease phase, or after being switchedon if no further selection is made. Changing this setting leads to increasedenergy consumption. - ...

Supervisor level 76 Main wash water You can select the water type for themain wash. - Cold Only cold water is used for the mainwash. - Hot Hot water is also added for the mainwash.Hot water can only be added if thewash temperature is above 30 °C. Programme durations will be longer ifthe machine is n...

Supervisor level 77 Mops temp. Standard plus The pre-set temperature can bealtered in the Mops plus  and Mops plus + rtu  programmes. - 40 °C (factory default)- 60 °C- 70 °C- 90 °C Mops Chemo-thermal disin. The pre-set disinfection process canbe altered in the Mops chemo-thermal disinfection  progra...

Supervisor level 78 Cloths Ch-th. disin. The pre-set disinfection process canbe altered in the Cloths chemo- thermal disinfection  programme. - 40 °C/20 min- 60 °C/20 min (factory default)- 70 °C/10 min Pre-treat cloths rpm The preset spin speed can be alteredin Finish/Pre-treat cloth programmes. - ...

Supervisor level 79 Cottons Pre-wash temp You can select the temperature for thepre-wash in the Cottons  programme. - 30 °C (factory default)- 35 °C- 40 °C- 45 °C Wash time Pre-wash You can increase the duration for thepre-wash in the Cottons  programme. - + 0 min (factory default)- + 6 min- + 9 min...

Supervisor level 80 Cottons rinses You can alter the number of rinsecycles carried out in the Cottons  and standard mop programmes. - 1 rinse cycle- 2 rinse cycles (factory default)- 3 rinse cycles- 4 rinse cycles- 5 rinse cycles Min. iron rinses You can alter the number of rinses car-ried out in th...

Supervisor level 81 Disinfection prog. code A code has to be entered to cancel adisinfection programme. The code canbe modified. The code is: 0 0 0 Tip: Make a note of your new code if you ever change it. Temp reduction The suds temperature can be reducedto prevent the suds from boiling tooearly in ...

Supervisor level 82 Availability of Miele digitalproducts The ability of Miele digital products de-pends on the availability of the servicesin your country.The different services are not availablein all countries.For information about availability, pleasevisit www.miele.com. WiFi/LAN Control the net...

Supervisor level 83 Network time The date and time can be synchron-ised over the network. - Off The date and time are not synchron-ised over the network. - As master The machines are in a network butare not connected to the Internet. Amachine is declared as the masterand sends data to the slave devi...

Supervisor level 84 Remote Operating data relating to the washingmachine (e.g. fault messages or noti-fications) is communicated externally. Factory default: On RemoteUpdate The RemoteUpdate function is used toupdate the software in your washingmachine.RemoteUpdate is activated by default.If you do ...

Supervisor level 85 Legal information Open source licences You can view information here. Copyrights and licences for operatorand control software Miele uses their own and third partysoftware which is not subject to any so-called open source licence for the oper-ation and control of the machine. Thi...

Supervisor level 86 Feedback signal to pay system Setting the feedback signal for the coinbox. - Factory default: Off- End of programme The feedback signal is sent at the endof the programme. - Release of the start button The feedback signal is sent when thestart button is released. - Start and prog...

Malaysia Miele Sdn BhdSuite 12-2, Level 12Menara Sapura Kencana PetroleumSolaris Dutamas No. 1, Jalan Dutamas 150480 Kuala Lumpur, MalaysiaPhone: +603-6209-0288Fax: +603-6205-3768 Miele New Zealand LimitedIRD 98 463 6318 College HillFreemans Bay, Auckland 1011, NZTel: 0800 464 353Internet: www.miele...