Miele KM 7576-2 FL MattFinish - User Manual

Warning and Safety instructions 7 Safety with children  Children under 8 years of age must be kept away from the hob un- less they are constantly supervised.  Children over 8 years of age may use the hob without supervision if its operation has been clearly explained to them and they are ableto us...

Warning and Safety instructions 8 Technical safety  Unauthorised installation, maintenance and repairs can cause con- siderable danger for the user. Installation, maintenance and repairsmust only be carried out by a Miele authorised technician.  Damage to the hob can compromise your safety. Check ...

Warning and Safety instructions 10 Correct use  The hob gets hot when in use and remains hot for a while after be- ing switched off. There is a danger of burning until the residual heatindicators go out.  Oil and fat can overheat and catch fire. Do not leave the hob unat- tended when cooking with ...

Warning and Safety instructions 13 Cleaning and care  Do not use a steam cleaning appliance to clean this hob. The steam could reach electrical components and cause a short cir-cuit.  If the hob is installed above a pyrolytic oven or cooker, do not use the hob during a pyrolytic cleaning programme...

Sustainability and environmental protection 14 Energy saving tips - Cook in covered pots and pans if pos- sible. This prevents heat escaping un-necessarily. - Cook with as little water as possible.- Once food has come to the boil or the pan is hot for frying, reduce the heatto a lower power level. -...

Familiarisation 15 Your hob a PowerFlex cooking zone with TwinBooster b PowerFlex cooking zone with TwinBoostercan be combined with PowerFlex cooking zone  to form PowerFlex cooking area c PowerFlex cooking zone with TwinBoostercan be combined with PowerFlex cooking zone  to form PowerFlex cooking...

Familiarisation 16 Controls and display b a c e d f i l h j g k a Stop&Go sensor controlTo stop/start a cooking process in progress b Hob On/Off sensor control c Wipe protection sensor controlTo lock the sensor controls d PowerFlex cooking zones sensor controlFor manual connection/disconnection ...

Familiarisation 17 Cooking zones Cooking zone Size in cm 1 Max. rating in watts for 230 V 2 Linked cook- ing zone 3 Ø   15–23 15 x 15 – 23 x 19 NormalTwinBooster, level 1TwinBooster, level 2 2100 3000 3650   15–23 15 x 15 – 23 x 19 NormalTwinBooster, level 1TwinBooster, level 2 2100 3000 3650  ...

Familiarisation 18 Power management Total power The hob has a maximum total permittedpower consumption which cannot beexceeded for safety reasons.The higher the total permitted powerconsumption of the hob, the morepower levels/functions can be used onall cooking zones at the same time.If the set pow...

Familiarisation 19 Operating principles Hob when switched off When the hob is switched off, you canonly see the printed symbols for thesensor controls and the numerical dis-play. More sensor controls light upwhen the hob is switched on. Operation a Sensor controls and indicators This ceramic glass h...

Familiarisation 20 Functions Con@ctivity 3.0 Con@ctivity 3.0 is the direct commu-nication system between your hob and aMiele cooker hood. Communication isachieved by means of networking.Con@ctivity 3.0 enables the cookerhood to operate automatically depend-ing on the operating status of your hob.Fur...

Familiarisation 21 System lock If the system lock is activated, then thehob cannot be switched on. Safety lock The safety lock is activated when thehob is switched on. When the lock is ac-tivated, the hob can be operated onlyunder certain conditions. Recall If the hob is switched off by mistakedurin...

Familiarisation 22 Safety switch-off Sensor controls are covered Your hob will turn off automatically ifone or several of the sensor controls re-main covered for longer than10 seconds, for example, by finger con-tact, food boiling over or by an objectsuch as an oven glove or tea towel.   flashes br...

Familiarisation 23 Overheating protection In order to prevent the hob from beingdamaged by excessive temperatures,the overheating protection mechanismintervenes in one of the following ways: Overheating protection measures - If the Booster function is switched on, it will stop. - The set power level...

Commissioning 24 Unpacking the hob  Please stick the data plate for the ap-pliance, supplied with this document-ation, in the space provided in the“Customer Service Department” sec-tion of this booklet.  Remove any protective foil and stick-ers. Cleaning the hob for the firsttime  Before using fo...

Commissioning 25 Connecting via the Miele app - A home WiFi network is available.- The signal of your WiFi network is sufficiently strong in the placewhere your hob is installed. - There is no direct WiFi connection between the hob and a Mielecooker hood (Con@ctivity 3.0). - The Miele app is install...

Commissioning 26 Cancelling the process  Touch any sensor control. Resetting settings Reset the settings if you are disposingof your hob, selling it or putting a usedhob into operation. This is the only wayto ensure that all personal data hasbeen removed and the previous ownerwill no longer be able...

Commissioning 27 Establishing a direct connectionwith the cooker hood The hob requires max. 2 W in networkedstandby. Availability of the WiFi connection The WiFi connection shares a frequencyrange with other appliances (includingmicrowave ovens and remote controltoys). This can give rise to sporadic...

Operation 29 Safety notes for operation  Risk of fire with overheated food. Unattended food can overheat and catch alight.Do not leave the hob unattended whilst it is being used.  Risk of burning due to hot cooking zones. The cooking zones will be hot after use.Do not touch the cooking zones while...

Operation 30 Switching the hob on  Touch the   sensor control. Further sensor controls will light up. If no further entry is made, the hob willswitch itself off after a few seconds forsafety reasons. Switching off a cooking zone/the hob Switching the hob off  To switch off the hob and all the coo...

Operation 31 Power level Setting the power level Permanent pan recognition is activatedas standard (see “Adjusting settings”).When the hob is switched on and youplace an item of cookware on one of thecooking zones, all the sensor controlsfor the numerical display will light up.  Place the cookware ...

Operation 32 Booster Activating the Booster When the Booster function is activated,the settings for the linked cooking zonemay be changed, see “Familiarisation –Power management”.You can use the Booster: - On 2 cooking zones at the same time, or - On the middle or right PowerFlex cooking area, or - ...

Operation 33 Auto heat-up The heat-up time depends on whichcontinued cooking setting has beenchosen: Continued cook- ing setting* Heat-up time [min:sec] 1 Approx. 0:15 1. Approx. 0:15 2 Approx. 0:15 2. Approx. 0:15 3 Approx. 0:25 3. Approx. 0:25 4 Approx. 0:50 4. Approx. 0:50 5 Approx. 2:00 5. Appro...

Operation 34 Timer Setting timer durations A duration of between 1 minute ( : ) and 9 hours 59 minutes ( : ) can be set.Durations of up to 59 minutes areshown in minutes (00:59) and durationsof more than 60 minutes are shown inhours and minutes.Durations are entered: - Using the left or front ...

Operation 36 System lock Activating the system lock All sensor controls are locked. A setminute minder time will continue tocount down.  Touch the   sensor control for 6 seconds. The seconds can be seen countingdown in the timer display. When thistime has elapsed,   will appear in the timer dis...

Operation 37 Activating the Recall function  Switch the hob on again. The previously set power levels flash.  Press one of the flashing power levelindicators immediately. All settings are restored. Keeping warm Activating /deactivating the Keepingwarm function The Keeping warm function cannot beus...

Operation 38 Hob data Displaying the model identifier/serialnumber There must not be any cookware onthe hob.  Switch the hob on.  Press the 0 sensor control on any nu-merical display.  Press the 0 and 4 sensor controls onthe numerical display at the sametime for 6 seconds. Numbers will appear in ...

Setting ranges for the power levels 39 The hob is programmed with 9 power levels at the factory. If you wish to fine-tune asetting, you can extend the power level range to 17 power levels (see “Adjustingsettings”). Setting range Factory set- ting (9 power levels) Extended set- ting (17 power levels)...

Good to know 40 How induction hobs work An induction coil is located under eachinduction cooking zone. The coil createsa magnetic field that reacts directly withthe base of the pan and heats it up. Thecooking zone itself is heated up indir-ectly by the heat given off by the pan.An induction cooking ...

Good to know 41 Pans Suitable cookware - Stainless steel cookware with a mag- netic base - Enamelled steel cookware- Cast iron Please be aware that the properties ofthe cookware base can affect the even-ness with which the food heats up (e.g.when making pancakes). The base ofthe pan must be able to ...

Adjusting settings 42 Accessing programming mode The   sensor is located approx. 1 cm (index finger width) to the left of the   sensor. The hob is switched off.  Press and hold the   and   sensor controls until the   sensor control lights up and   appears in the timer display. After a few se...

Cleaning and care 46 Safety notes on cleaning and care  Risk of burns due to hot surfaces. All parts of the hob may be hot after use.Switch the hob off.Allow the hob to cool down before cleaning it. All surfaces could be discoloured or damaged if unsuitable cleaningagents are used or if residues fr...

Cleaning and care 47 When to clean  Clean the hob after every use. Removing light soiling  Clean the entire ceramic surface ofthe hob with a damp, soft cloth and asolution of water and a little washing-up liquid. Please follow the cleaningagent manufacturer ’s instructions. Removing stubborn soili...

Troubleshooting 48 Messages in the display Problem Cause and remedy   will flash alternately with   in the timer dis- play and a tone willsound. The hob is incorrectly connected.  Disconnect the hob from the mains electricity sup-ply.  Contact the Customer Service Department. The hobmust be c...

Troubleshooting 49 Problem Cause and remedy In the timer display E-number, e.g. E-0, willflash alternately with  ,  ,  ,  ,  ,  ,  or  . The fan is blocked or defective.  Make sure it has not been blocked by an object.  Remove the obstruction.  If this fault message contin...

Troubleshooting 50 Unexpected behaviour Problem Cause and remedy The power level selectedis flashing. No cookware is present on the cooking zone. Unsuitable cookware is present on the cooking zone. The diameter of the base of the cookware is too small. Suitable cookware has been removed from the coo...

Troubleshooting 51 Problem Cause and remedy The Booster level hasdeactivated early auto-matically. The overheating protection mechanism has been ac-tivated.  Allow the hob to cool down.  Rectify the causes of the overheating (see “Familiar-isation – Overheating protection”).  Check that the hob i...

Troubleshooting 52 Unsatisfactory results Problem Cause and remedy The food in the pan doesnot heat up when theAuto heat-up function isswitched on. A large amount of food is being heated up.  Start cooking at the highest power level and thenturn down to a lower one manually later on. The pan is not...

After sales service 53 Information to help you rectify faults yourself and about Miele spare parts can befound at www.miele.com/service. Contact in the event of a fault In the event of a fault which you cannot remedy yourself, please contact your Mieledealer or Miele Customer Service. You can book a...

After sales service 54 Note for test institutes Test food acc. to EN 60350-2 9 power levels are programmed at the factory.For testing in accordance with the above standard, programme the hob to the ex-tended power level setting (see “Adjusting settings”). Test food  Pan base (mm) Lid Power level Pr...

Optional accessories 55 Miele offer a comprehensive range ofuseful accessories as well as cleaningand conditioning products for yourMiele appliances.These products can be ordered throughthe Miele Webshop.They can also be ordered from Miele(see end of this booklet for contact de-tails) or from your M...

Installation *INSTALLATION* 56 Safety notes for installation  Risk of damage from incorrect installation. Incorrect installation can cause damage to the hob.The hob must only be installed by a qualified specialist.  Risk of electric shock from mains voltage. Incorrect connection to the mains suppl...

Installation *INSTALLATION* 57 Additional safety notes for surface-mounted installation  Damage caused by incorrect installation. Using sealant under the hob could result in damage to the hob andthe worktop if the hob ever needs to be removed.Do not use sealant between the hob and the worktop.The s...

Installation *INSTALLATION* 58 Additional safety notes for flush-fit installation  Damage from unsuitable sealant. Unsuitable sealant can damage natural stone.For natural stone worktops and natural stone tiles, only use siliconesealant that is specially formulated for natural stone. Follow themanuf...

Installation *INSTALLATION* 59 Safety distances Safety distance above the hob The following must be ensured betweenthe hob and the cooker hood above it: - The safety distance specified by the manufacturer of the cooker hood mustbe maintained. - When two or more appliances which have different safety...

Installation *INSTALLATION* 60 Safety distance behind and to the sideof the hob The minimum safety distances shownbelow must be maintained between theappliance and a tall unit or wall: - Between the back    of the worktop cut-out and the rear edge of the work-top:50 mm and - On the right side    b...

Installation *INSTALLATION* 61 Safety distance underneath the hob To install the hob while maintaining thesafety distances, you can choose from3 variants: 1. Without intermediate shelf or base panel 2. With intermediate shelf3. With an air intake-optimised base panel Further instructions are describ...

Installation *INSTALLATION* 62 1. Without intermediate shelf or base panel To ensure sufficient ventilation to the hob, a minimum safety distance must be leftbetween the underside of the hob and any drawer or oven.The minimum safety distance between the underside 1 of the hob and: - Upper edge of dr...

Installation *INSTALLATION* 63 3. Air intake-optimised base panel The performance of the hob depends on the ventilation.The air intake-optimised base panel has openings where the fans are positioned.This section contains instructions for creating an air intake-optimised base panel. ≤ 40 mm ≥ 45 mm ≥...

Installation *INSTALLATION* 64 Positions and cut-outs of the ventilation openings X1.1 X1.2 Y1.1 Y1.2 X2.1 XB YB Y2.1 Not to scale. View from above. Surface-mounted cut-out shown.Also applies to flush-fit installation. a Middle of the cut-out height b Middle of the cut-out width c Cut-out for fan, r...

Installation *INSTALLATION* 65 Safety distance from the niche cladding If niche cladding is installed, a minimum safety distance must be maintainedbetween the worktop cut-out and the cladding. High temperatures can alter ordamage these materials. Flush-fit installation Surface-mounted installation a...

Installation *INSTALLATION* 66 Building-in dimensions for surface-mounted installation All dimensions are given in mm. a Front b Mains connection boxThe mains connection cable (L = 1440 mm) is supplied loose

Installation *INSTALLATION* 67 Installation dimensions for flush-fit installation All dimensions are given in mm. a Front b Mains connection boxThe mains connection cable (L = 1440 mm) is supplied loose c Stepped cut-out, natural stone worktop d Wooden batten 12 mm (not supplied)

Installation *INSTALLATION* 68 Installing a surface-mountedhob Preparing the worktop for surface-mounted installation  Remember to maintain the minimumsafety distances (see “Installation –Safety distances”).  Create the worktop cut-out.  Wooden worktops:Seal any cut surfaces with a specialvarnish...

Installation *INSTALLATION* 69 Installing the hob flush with theworktop Preparing the worktop for flush-fit in-stallation  Create the worktop cut-out. Remem-ber to maintain the minimum safetydistances (see “Installation – Safetydistances”).  Solid wood and tiled worktops:Fix the wooden battens 5,5...

Installation *INSTALLATION* 70 Electrical connection  Risk of damage from incorrect connection.Unauthorised installation, mainten-ance and repairs can cause consider-able danger for the user.Miele cannot be held liable for dam-age or injury caused by unauthorisedinstallation, maintenance or repairw...

Installation *INSTALLATION* 71 Disconnecting from the mains  Risk of electric shock. There is a risk of electric shock if theappliance is connected to the mainssupply during repair or service work.After disconnection, ensure the appli-ance cannot be switched back on bymistake. To disconnect the app...

Installation *INSTALLATION* 72 Wiring diagram Some connection methods are notpermitted in all installation locations.Ensure compliance with national reg-ulations and any additional regula-tions issued by the local electricityprovider. The maximum load per connected liveconductor is 3650 W. Hob with&...

Installation *INSTALLATION* 73 Product data sheets The following data sheets apply to the models described in this operating instruc-tion manual. Information for domestic electric hobs In acc. with regulation (EU) No. 66/2014 MIELE Model name/identifier KM 7576-2 FL Number of cooking zones and/or ar...

Installation *INSTALLATION* 74 EU Conformity declaration Miele hereby declares that this ceramic induction hob complies with Directive2014/53/EU. The complete text of the EU declaration of conformity is available from one of thefollowing internet addresses: - Products, Download from www.miele.ie- Fo...

United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TWTel: 0330 160 6600, Internet: www.miele.co.uk, E-mail: [email protected] Australia Miele Australia Pty. Ltd.ACN 005 635 398ABN 96 005 635 398Level 4, 141 Camberwell RoadHawthorn East, VIC 3123Tel: 1300 464 353E-mail: [em...