Makita LS1040 - Manual - manualsarea.com

Page 2 - SPECIFICATIONS; Symbols; Intended use

2 ENGLISH (Original instructions) SPECIFICATIONS Model LS1040 / LS1040S Blade diameter 255 mm -260 mm Hole diameter For all countries other than European countries 25.4 mm and 25 mm For European countries 30 mm Max. Cutting capacities (H x W) with blade 260 mm in diameter Miter angle Bevel angle 0° ...

Page 3 - EC Declaration of Conformity; SAFETY INSTRUCTIONS

3 a fuse or protective circuit breaker having slow tripping characteristics. For Model LS1040,LS1040S ENG102-3 Noise The typical A-weighted noise level determined according to EN61029: Sound pressure level (L pA ) : 93 dB(A) Sound power level (L WA ) : 106 dB(A) Uncertainty (K) : 3 dB(A) Wear ear pr...

Page 5 - SAVE THESE INSTRUCTIONS.; Installing auxiliary plate

5 14. Make sure that the turn base is properly secured so it will not move during operation. 15. For your safety, remove the chips, small pieces, etc. from the table top before operation. 16. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 17. Make sure the...

Page 6 - FUNCTIONAL DESCRIPTION; Blade guard

6 1 001792 This tool should be bolted with two bolts to a level and stable surface using the bolt holes provided in the tool's base. This will help prevent tipping and possible injury. 1 001856 FUNCTIONAL DESCRIPTION CAUTION: • Always be sure that the tool is switched off and unplugged before adjust...

Page 7 - turn base

7 Maintaining maximum cutting capacity 1 2 002257 2 1 3 001540 This tool is factory adjusted to provide the maximum cutting capacity for a 260 mm saw blade. When installing a new blade, always check the lower limit position of the blade and if necessary, adjust it as follows: First, unplug the tool....

Page 8 - ASSEMBLY; Installing or removing saw blade

8 • When not using the tool, remove the lock-off button and store it in a secure place. This prevents unauthorized operation. • Do not pull the switch trigger hard without pressing in the lock-off button. This can cause switch breakage. For European countries 2 1 004853 To prevent the switch trigger...

Page 9 - Dust bag

9 2 1 4 3 001787 CAUTION: For all countries other than European countries 1 2 3 4 5 6 004852 CAUTION: • The silver ring 25.4 mm in outer diameter is factory-installed onto the spindle. The black ring 25 mm in outer diameter is included as standard equipment. Before mounting the blade onto the spindl...

Page 10 - Vertical vise; assembly

10 This tool is equipped with the sub-fence. It should be positioned as shown in the figure. CAUTION: • When performing left bevel cuts, flip the fence over to the left position as shown in the figure. Otherwise, it will contact the blade or a part of the tool, causing possible serious injury to the...

Page 11 - OPERATION; cutting

11 When cutting long workpieces, use the holder-rod assembly (optional accessory). It consists of two holder assemblies and two rods 12. 2 1 002246 CAUTION: • Always support long workpieces level with the top surface of the turn base for accurate cuts and to prevent dangerous loss of control of the ...

Page 12 - Cutting aluminum extrusion; repetitive; Carrying tool; extrusion

12 Miter angle Bevel angle Left and Right 0 - 45 45 006366 When performing compound cutting, refer to "Press cutting", "Miter cutting" and "Bevel cut" explanations. 5. Cutting aluminum extrusion 12 345 001844 When securing aluminum extrusions, use spacer blocks or pieces of s...

Page 13 - MAINTENANCE; Adjusting the cutting angle; angle

13 001774 CAUTION: • Always secure all moving portions before carrying the tool. • Stopper pin is for carrying and storage purposes only and not for any cutting operations. MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or ma...

Page 14 - ACCESSORIES

14 1 2 3 4 001769 (2) 45° bevel angle 1 2 3 4 001770 Adjust the 45° bevel angle only after performing 0° bevel angle adjustment. To adjust left 45° bevel angle, loosen the lever and tilt the blade to the left fully. Make sure that the pointer on the arm points to 45° on the bevel scale on the arm. I...