Makita DF010DSE - Manual
Makita DF010DSE Impact Driver – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – epair; Retaining ring pliers with long bent nails
- Page 3 – Note
- Page 5 – iring diagram
PRODUCT
P 1/
5
T
ECHNICAL INFORMATION
7.2
1.0
30
650
6.35 (1/4) Hex
200
High
Low
Li-ion
Models No.
Description
C
ONCEPT AND MAIN APPLICATIONS
S
pecification
S
tandard equipment
O
ptional accessories
DF010D
7.2V Cordless Driver Drill
Model No.
DF010DSE
Battery
BL7010
Yes/ 2 pcs
Charger
DC07SA Plastic carrying case
Dimensions: mm (")
Width (W)
Height (H)
(L1)
Length
224 (8-7/8)
(L2)
279 (11)
43 (1-11/16)
141 (5-9/16)
L2
L1
H
No load speed: min
-1
= rpm
Max. output: W
Battery
21 stages + drill mode
Torque setting
Cell
Voltage: V
Capacity: Ah
Driving shank: mm (")
Capacities: mm (")
0.3 - 3.0 [3.0 - 30]
Clutch torque setting: N.m [kgf.cm]
Steel
Wood
5 (3/16)
6 (1/4)
Yes
Yes
Driver bits, Socket bits, Hex shank drill bits for wood, Hex shank drill bits for steel,
Charger DC07SA, Battery BL7010
Model DF010D is a straight type cordless driver drill
compact and lightweight for easy handling.
Uses new 7.2V Li-ion battery of stick type as a power unit.
Can be easily converted from straight- to pistol-type.
This product is available with the following model name.
The model also includes the accessories listed below
in "Standard equipment".
W
Yes
Yes
Yes
0.55 (1.2)
Soft start
Reverse switch
LED job light
Yes
Electric brake
Net weight: kg (lbs) [with battery BL7010]
Note:
The standard equipment for the tool shown above may differ by country.
Phillips bit 1-50 (double-end) ........ 1 pc
Phillips bit 2-50 (double-end) ........ 1 pc
(L1): Length in Straight form
(L2): Length in Pistol form
Lock torque: N.m (in.lbs)
Max. fastening
torque: N.m
Hard joint
Soft joint
5.0 (44)
3.6
5.6
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
(1) Remove two Set plates from Handle set as follows: Insert a small slotted screwdriver through the punched hole of set plate and move Set plate in the direction of the arrow using the screwdriver while pushing Set plate against Handle set. ( Fig.2 ) (2) Handle set can be removed from Motor housing...
(4) Separate LED from Housing, then remove a assembled unit that consists of Switch unit, DC motor and Gear assembly etc. ( Fig. 5 ) (5) Remove Speed change lever assembly and Switch unit (microswitch / green color) from Gear assembly. (6) Remove Gear assembly from DC motor. Gear assembly can be rep...
Fig. D-2 hook of Controller Terminal Motor housing L Switch unit (large) Route LED lead wires between ribs. Route Lead wires between emboss and rib. Route Lead wires between Switch unit (large) and rib. emboss Connector LED rib ribs rib Route this Lead wire (red) through the hook of Controller. Fix ...
