LG LDG3016ST - Manual - manualsarea.com

Page 2 - I N S TA L L AT I O N I N S T RU C T I O N S; BEFORE YOU BEGIN; Read these instructions completely; • IMPORTANT; INSTALLATION SAFETY INSTRUCTIONS; READ ALL INSTRUCTIONS BEFORE INSTALLATION

2 I N S TA L L AT I O N I N S T RU C T I O N S BEFORE YOU BEGIN Read these instructions completely and carefully. Installation of this range must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. In Canada, installation ...

Page 3 - WARNING; WHAT TO DO IF YOU SMELL GAS; ENGLISH

3 I N S TA L L AT I O N I N S T RU C T I O N S INSTALLATION SAFETY INSTRUCTIONS (continued) READ ALL INSTRUCTIONS BEFORE INSTALLATION This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert sy...

Page 5 - TOOLS YOU WILL NEED; CAUTION

5 I N S TA L L AT I O N I N S T RU C T I O N S TOOLS YOU WILL NEED MATERIALS YOU MAY NEED • Gas line shut-off valve• Pipe joint sealant that resists action of natural and LP gases. • Flexible metal appliance connector (3/4” or 1/2” NPT x 1/2” I.D.) Never use an old connector when installing a new ra...

Page 6 - DIMENSIONS AND CLEARANCES; DIMENSIONS

6 I N S TA L L AT I O N I N S T RU C T I O N S DIMENSIONS AND CLEARANCES Provide proper clearances between the range and adjacent combustible surfaces. These dimensions must be met for safe use of your range. The location of the electrical outlet and pipe opening (see “GAS PIPE AND ELECTRICAL OUTLET...

Page 7 - LOCATION

7 I N S TA L L AT I O N I N S T RU C T I O N S Do not locate your range where it may be subject to strong drafts. Any openings in the floor or wall behind the range should be sealed. Make sure the openings around the base of the range that supply fresh air for combustion and ventilation are not bloc...

Page 8 - GAS PIPE AND ELECTRICAL OUTLET LOCATIONS

8 I N S TA L L AT I O N I N S T RU C T I O N S Your range is designed to operate at a pressure of 5” of water column on natural gas or 10” of water column on LP. Make sure you are supplying your range with the type of gas for which it is configured.This range is convertible for use on natural or LP ...

Page 9 - CONNECT THE RANGE TO GAS; FLEXIBLE CONNECTOR HOOKUP

9 I N S TA L L AT I O N I N S T RU C T I O N S 2. CONNECT THE RANGE TO GAS Shut off the range gas supply valve before removing the old range and leave it off until the new hook-up has been completed. Because hard piping restricts movement of the range, the use of a CSA International-certified flexib...

Page 10 - ELECTRICAL REQUIREMENTS; ELECTRICAL CONNECTIONS

10 I N S TA L L AT I O N I N S T RU C T I O N S ELECTRICAL REQUIREMENTS 120 Volt, 60 Hertz, properly grounded dedicated circuit protected by a 15 or 20 Amp circuit breaker, or slow blow fuse. GROUNDING IMPORTANT: FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. The power cord of this a...

Page 11 - ASSEMBLE THE SURFACE BURNERS; ELECTRIC IGNITION; CHECK IGNITION OF SURFACE BURNERS

11 I N S TA L L AT I O N I N S T RU C T I O N S Place the burner caps and heads on the cooktop. Make sure that the caps and heads are placed in the correct locations. There is one small, one medium, one large and one extra large burner head and cap. Make sure the hole in the burner head is positione...

Page 12 - ADJUST THE SURFACE BURNER TO THE LOW

12 I N S TA L L AT I O N I N S T RU C T I O N S 7. ADJUST THE SURFACE BURNER TO THE LOW FLAME(SIMMER) SETTING. 1) Light all surface burners.2) Turn the knob on the burner being adjusted to “LO”. 3) Remove knob.4) Insert a small, flat bladed screwdriver into the valve shaft as shown in Fig. 1. On rig...

Page 13 - AIR SHUTTER ADJUSTMENT FOR BAKE AND BROIL

13 I N S TA L L AT I O N I N S T RU C T I O N S To check ignition of the Bake burner, follow the steps below: 1) Remove all packing from inside the oven cavity. 2) Press "Bake" (350 will be shown in the display). 3) Press Start. It may take between 30 and 90 seconds for the burner to start h...

Page 15 - WHEN ALL HOOKUPS ARE COMPLETE; CONVERTING TO LP GAS; (OR CONVERTING BACK TO NATURAL GAS FROM LP)

15 I N S TA L L AT I O N I N S T RU C T I O N S Make sure all controls are left in the off position. Make sure the flow of combustion and ventilation air to the range is unblocked. WHEN ALL HOOKUPS ARE COMPLETE This range leaves the factory set for use with natural gas. The conversion to LP gas must...

Page 16 - M e m o

Page 17 - Register your product Online!

Printed in Mexico www.lg.com Register your product Online! LG Customer Information Center 1-800-243-0000 1-888-865-3026 USA, Consumer User USA, Commercial User

LG LDG3016ST - Manual

Table of Contents:

Other Manuals for LG LDG3016ST

Summary

Other LG Ranges Models