Page 2 - The quick way to start with the TPS300 Mining Programs.; The quick way to start
TPS300 Mining Manual-1.0.0en 2 To use equipment in the permitted manner, please refer to thedetailed safety instructions in the TPS300 Basic Series UserManual (English version). The quick way to start with the TPS300 Mining Programs. The quick way to start © 2000 Leica Geosystems AG Heerbrugg, ® All...
Page 4 - Contents
TPS300 Mining Manual-1.0.0en 4 Contents Introduction ................................................ 5 How to use this manual ............................... 5Symbols used in the sequence of operation 5 Peg Survey ................................................. 6 Introduction .......................
Page 5 - Introduction; How to use this manual; Press the fixed key PROG
TPS300 Mining Manual-1.0.0en Introduction 5 Introduction How to use this manual This manual describes the basicoperation of the TPS300 Miningfield programs. It shall be usedtogether with a TPS300instrument. For detailed description aboutthe whole functionality of theTPS300 instrument please torefer ...
Page 6 - Peg Survey; • Coordinates of station
TPS300 Mining Manual-1.0.0en Peg Survey 6 Peg Survey Mining_z01 Introduction The application "Peg Survey" isused to establish a forward peg(point). It is used to control theintermediate horizontal anglebetween backsight and foresightpoints. It also checks thehorizontal distances and heightso...
Page 7 - Before starting Peg Survey; • Station coordinates
TPS300 Mining Manual-1.0.0en Peg Survey 7 Before starting Peg Survey Data uploading using "MiningEditor" • Station coordinates (East, North, Height,Grade elevation) • Backsight point coordinates (East, North, Height,Grade elevation) • Tolerances, sequence, number of sets • Job definition Upl...
Page 8 - Start and execution Peg Survey; press
TPS300 Mining Manual-1.0.0en Peg Survey 8 Start and execution Peg Survey Input Station PtID : 100 hi : -1.265 m <EXIT> <SET> Start "Peg Survey" fromthe program menu. Start-up menu: > Step 3 Choose "Start" and press , then enter point number(PtID) andinstrument height(h...
Page 9 - Error messages; One Set; Two Sets; • The point number entered is
TPS300 Mining Manual-1.0.0en Peg Survey 9 Error messages Survey will be executed according to the following settings: No of Sets: 3 Sequence: BFFB <OK> Number of sets:One set means to measure twotimes the backsight point andtwo times the foresight point inboth faces. The meaning of set isdescr...
Page 10 - • BFFB; Proceeding Peg Survey
TPS300 Mining Manual-1.0.0en Peg Survey 10 Sequence: It defines the measuringsequence. Options: • BFFB Backsight-Foresight-Foresight-Backsight • BFBF Backsight-Foresight-Backsight-Foresight • BBFF Backsight-Backsight-Foresight-Foresight <OK> Leaves this dialogand proceed to thenext dialog. Set...
Page 11 - Proceeding Peg Survey, continued
TPS300 Mining Manual-1.0.0en Peg Survey 11 Backsight Point 1/3 PtID : 150 Hz : 98°12'45" V : 99°45'23" hr : -1.263 m HD : ----.--- m <EXIT> <SEARCH> <MEAS> Proceeding Peg Survey, continued Measure Foresight Point PtID: ----- <OK> > Step 7 Enter a desiredforesight p...
Page 12 - Repeat
TPS300 Mining Manual-1.0.0en Peg Survey 12 Foresight Point 1/3 PtID : 151 Hz : 198°12'45" V : 94°45'23" hr : -1.632 m HD : ----.--- m <EXIT> <MEAS> Proceeding Peg Survey, continued <REJECT> Reject the measurement andmeasure the setagain. <ACCEPT> Accept the result and...
Page 13 - Results; Height residual
TPS300 Mining Manual-1.0.0en Peg Survey 13 Results Sample dialog: TOLERANCES MET ! (PAGE1) dHz : 00°00'25" TolHz : 00°00'50" dHD BS: 0.001 m dHD FS: 0.003 m TolHD : 0.006 m TOLERANCES MET ! (PAGE2) dH BS : 0.003 m dH FS : 0.001 m TolH : 0.004 m Set No: <ALL SETS> <EXIT> <OK>...
Page 15 - Coordinates foresight point:; Easting; Saving data
TPS300 Mining Manual-1.0.0en Peg Survey 15 Results, continued <OK> Quits the program. <EXIT> Terminates themeasurement andreturns to the start-up menu. The following result data arestored in the internal memory: Result: mHz: Averageintermediatehorizontal anglebetween backsightpoint and f...
Page 16 - Front Line Peg
TPS300 Mining Manual-1.0.0en Front Line Peg 16 Front Line Peg Introduction The application "FLP" is used tomark a new line peg (Front linepeg). This application is similarto "Peg Survey" and there isonly one set of measurementrequired. For a more detail explanation of"FLP", p...
Page 17 - Grades
TPS300 Mining Manual-1.0.0en Grades 17 Grades Mining_z04 Introduction "Grades" application is used tomark gradelines along the sidewalls of the mines (tunnels). Itallows users to input the slopegradient and an offsetconcerning the grade point. Itcomputes the stake out heightdifference. The p...
Page 18 - Before starting Grades; • Station setup; Start and execution Grades
TPS300 Mining Manual-1.0.0en Grades 18 Before starting Grades • Station setup • Application "FLP" is done Start and execution Grades Menu dialog of "FLP": Sample dialog: GRADES Grade : 1: 150 Height: 0.500 m <EXIT> <SET> If the slope gradient(station until foresightpoint)...
Page 19 - Start and execution Peg Survey, continued; Slope gradient explained:; Height difference explained:
TPS300 Mining Manual-1.0.0en Grades 19 Mining_z06 Start and execution Peg Survey, continued Mining_z05 150 1 H New Gradeline > Step 1 Enter the slopegradient(proportion e.g.1:150). Slope gradient explained: Gradeline > Step 2 Enter the heightdifference. Height difference explained: H: Current ...
Page 20 - Gradeline Marking; until
TPS300 Mining Manual-1.0.0en Grades 20 Gradeline Marking GRADELINE MARKING PtID : 100 dHgt : 0.552 m dHD : 3.123 m Hz : 126°56'23" HD : 10.365 m <EXIT> <PREV> <MEAS> Sample dialog: > Step 4 Enter a desired pointnumber (PtID). > Step 5 Aim at target pointand measure. <M...
Page 23 - Offset
TPS300 Mining Manual-1.0.0en Offset 23 Offset Introduction "Offset" application is generallyused to obtain sections of thetunnels for volume computationas well as mapping of thetunnels. It allows users to inputoffset value (left, right, up anddown) and computes aftermeasurement the actualcoo...
Page 24 - Before starting Offset; Start and execution Offset; Using
TPS300 Mining Manual-1.0.0en Offset 24 Before starting Offset • Station setup • Application "FLP" is done Start and execution Offset Menu dialog of "FLP": OFFSET PtID : 100 Offset: 1.500 m LEFT Hz : 123°12'36" HD : -----.--- m <EXIT> <MEAS> Sample dialog: > Step 1 ...
Page 25 - Start and execution Offset, continued; Definition of offset explained:
TPS300 Mining Manual-1.0.0en Offset 25 Start and execution Offset, continued Definition of offset explained: Mining_z10 Up Down Right Left > Step 3 Aim at target pointand measure. <MEAS>, ALL or DIST/REC Measurement istriggered and storedin the internalmemory. <EXIT> Leaves theapplica...
Page 27 - Mining Editor; Installation on the PC; • Data Import & Export
TPS300 Mining Manual-1.0.0en Mining Editor 27 Mining Editor Introduction "Mining Editor" (PC ProgramPackage) is a Windows-basedprogram used for the dataexchange between the TPS300Series and the PC. Installation on the PC The installation program for the"Mining Editor" can be found on...
Page 28 - • Define and upload; Program content, continued; Practical Examples
TPS300 Mining Manual-1.0.0en Mining Editor 28 • Define and upload TolerancesDefining tolerances, editingtolerances (passwordprotected), uploadingtolerances • Creating fixpoint files Creating and editing offixpoint files (Coordinates) Program content, continued Practical Examples The following pages ...
Page 29 - Enter number of sets.
TPS300 Mining Manual-1.0.0en Mining Editor 29 First Example (Creating fixpoint files, define tolerances, uploading) Creating fixpoint files > Step 1 Open a new file: File à New > Step 2 Enter point number, coordinates,backsight reference point, gradeelevation. > Step 3 Save the created coor...
Page 30 - a) Select a tolerance type; Options
TPS300 Mining Manual-1.0.0en Mining Editor 30 First Example (Creating fixpoint files, define tolerances, uploading), continued > Step 5 a) Select a tolerance type (Primary, Secondary,Tertiary). b) Enter the values for: • Horizontal Angle Limit• Horizontal Distance Limit• Height Limit Upload Fixpo...
Page 31 - Second Example (Importing of fixpoints in ASCII format); Process import fixpoint files; Open the selected file.; Save as
TPS300 Mining Manual-1.0.0en Mining Editor 31 Second Example (Importing of fixpoints in ASCII format) Process import fixpoint files The "Mining Editor" allows to importfixpoint files in ASCII format. > Step 1 File à Open > Step 2 ASCII-File search and select. > Step 3 Open the selec...
Page 32 - Leica Geosystems AG
Leica Geosystems AG CH-9435 Heerbrugg (Switzerland) Phone +41 71 727 31 31 Fax +41 71 727 46 73 www.leica-geosystems.com Printed in Switzerland - CopyrightLeica Geosystems AG, Heerbrugg,Switzerland 2000Original text 723346-1.0.0en Leica Geosystems AG, Heerbrugg,Switzerland, has been certified asbein...
