Leica MZ16 FA - Manual - manualsarea.com

Page 2 - Table of contents; Page

2 Leica lamp housing and mercury burner Table of contents Page 1. Safety concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Safety precautions . . . . . . . . . ...

Page 3 - In particular, please note

1.1 Description 1.2 Safety precautions For the Leica MZ16 FA 3 Leica lamp housing and mercury burner 1. Safety concept The Leica 106 z lamp housing is the light source for the fluorescence stereomicroscope Leica MZ16 FA as well as thefluorescence module for Leica stereomicroscopes. The Leica lamp ho...

Page 4 - Burn hazard

Lamp housing The Leica MZ16 FA fluorescence stereomicroscope and the fluorescence module for Leica stereomicroscopes may only beused in combination with the Leica lamp housing for 100W or50W mercury burners, their corresponding supply units andstray-light protection. Leica Microsystems accepts no li...

Page 5 - Supply units; For the ebq supply unit:

Supply units The 100W mercury burners are powered by the ebq 100 supplyunit. Read the separate instruction manual provided with thissupply unit. The supply unit for 50W mercury burners is described in this manual. For the ebq supply unit: only fuses of the specified type with the listed rated curren...

Page 7 - Follow the safety instructions!; Typical; the mercury burner

The Leica Microsystems 106 z lamp housing is used.If the 105 z lamp housing model is available, it can also be used. Follow the safety instructions! The following gas discharge lamps can be used. They requiredifferent types of lamp mounts. Order No. Typical Life 500 137 50W high-pressure mercury bur...

Page 10 - Remove the collector.; protection; Assembling the lamp housing

Unscrew the hexagon-head screw on theadapter part using an Allen key. Insert the lamp housing into the adapterpart and tighten the hexagon-head screw. Between the lamp housing and the lamp base, there are gapsthrough which UV light escapes, and which can temporarily irradiate the hands of the user w...

Page 11 - Insert the collector

Pull the focusing knob outward. Carefully replace the collector and push itto the left until the focusing knob comes toa stop in the guide groove. Adjust the collector on a trial basis. Reinstall the lamp base and close the lamp housing. Insert the collector 11 Leica lamp housing and mercury burner

Page 12 - Connect the lamp housing cable to the supply unit.

4.1 Supply unit for lamp housing 106 z with 50W mercury lamp 12 Leica lamp housing and mercury burner Type 301-185.003/10372Input: 220V/240V ±10%220V ~ 50/60HzHg 50W L1/L2Osram No. 0-958P. Max. 320VA 1. On/off switch2. Operating time meter3. Switching between L1 and L2 burners4. Safety starter5. Swi...

Page 13 - Replacing the safety starter; Turn the safety starter counterclockwise and remove it.; burners

To minimize the risk of explosion, replace a discoloredhigh-pressure mercury burner promptly when it hasreached the end of its rated life. Follow the manufacturer’s specifications and the minute meteron the supply unit! Switch on the supply unit. The safety starter ignites the burner. If the burner ...

Page 14 - Danger of explosion from overheating; Adjusting the mercury burner

14 Leica lamp housing and mercury burner After installing the mercury burner, adjust it exactly as de-scribed. Never let the bright tips of the electric arcs, the focalspots, cross when projected. Danger of explosion from overheating Adjustment is also important to obtain a homogenous light surface ...

Leica MZ16 FA - Manual

Table of Contents:

Summary

Other Leica Models