Page 2 - Leica DISTO; Table of Contents
Leica DISTO TM E7400x 788480a 1 EN Table of Contents Instrument Set-up - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2Display...
Page 3 - Introduction; The symbols used have the following meanings:; Overview
Leica DISTO TM E7400x 788480a 2 EN Instrument Set-up Introduction The safety instructions and the user manual should be read through carefully before the product is used for the first time. The person responsible for the product must ensure that all users understand these directions and adhere to th...
Page 4 - Display
Leica DISTO TM E7400x 788480a 3 EN Instrument Set-up Display Horizontal measurement Units Stake out Ceiling area Wall area Circumference Measuring reference 2nd result Area / Volume Tilt angle Info Slope distance Addition / Subtraction Illumination Memory Timer Triangle area BatteryMin/Max Measuring...
Page 5 - Operations; Clear; ON; InFo; Adjusting measuring reference / tripod
Leica DISTO TM E7400x 788480a 4 EN Operations Switching ON/OFF Clear Message Codes ON OFF 2 sec Device is turned OFF. i Press ON but-ton 2 sec to start continuous laser mode. 1x Undo last action. 2x Leave actual func-tion, go to default operation mode. If the message " InFo " appears with a ...
Page 6 - Multifunctional endpiece; simultaneously
Leica DISTO TM E7400x 788480a 5 EN Operations Multifunctional endpiece i The orientation of the endpiece is automatically detected and the zero point is accordingly ad-justed. Distance unit setting Tilt unit setting Switch between the following units: 0.000 m 0.0000 m 0.00 m 0.00 ft 0‘00‘‘ 1/32 0‘00...
Page 7 - Keypad lock ON; ously; PRESS; within
Leica DISTO TM E7400x 788480a 6 EN Operations Beep ON/OFF Illumination ON/OFF 2 sec simultane- ously 2 sec simultane- ously Keypad lock ON Keypad lock OFF 2 sec simultane- ously PRESS MINUS 1 within 2 sec 2
Page 8 - Measuring Functions; Measuring single distance; Aim active laser at target.
Leica DISTO TM E7400x 788480a 7 EN Measuring Functions Measuring single distance 1 Aim active laser at target. 2 8.532 m 3 i Target surfaces: Measuring errors can occur when measuring to col-ourless liquids, glass, styrofoam or semi-permeable surfaces or when aiming at high gloss surfaces. Against d...
Page 9 - Area; Circumference
Leica DISTO TM E7400x 788480a 8 EN Measuring Functions Area 1 1x 2 Aim laser at first target point. 3 4 Aim laser at sec-ond target point. 24.352 m 2 5 i The result is shown in the main line and the measured value above. Partial Measurements: Press + or - after starting the first measurement. Measur...
Page 10 - Volume
Leica DISTO TM E7400x 788480a 9 EN Measuring Functions Volume 1 2x 2 Aim laser at first target point. 3 4 Aim laser at sec-ond target point. 5 6 Aim laser at third target point. 78.694 m 3 7 i The result is shown in the main line and the measured value above. 24.224 m 2 208.703 m 2 80.208 m 78.694 m...
Page 11 - Triangular area
Leica DISTO TM E7400x 788480a 10 EN Measuring Functions Triangular area 1 3x 2 Aim laser at first target point. 3 4 Aim laser at sec-ond target point. 5 6 Aim laser at third target point. 24.352 m 2 7 33.852 m 24.352 m 2 40.8 ° 2 sec Angle included by the first two measurementsCircumference Triangul...
Page 12 - Aim laser at lower point.
Leica DISTO TM E7400x 788480a 11 EN Measuring Functions Pythagoras (3-point) 1 4x 2 Aim laser at upper point. 3 4 Aim laser at rec-tangular point. 5 6 Aim laser at lower point. 8.294 m 7 i The result is shown in the main line and the measured distance above. Pressing the measuring key for 2 sec in t...
Page 14 - Stake out
Leica DISTO TM E7400x 788480a 13 EN Measuring Functions Stake out i Two different distances (a and b) can be entered to mark off de-fined measured lengths. 1 2 3 a b b a = b 1 2 3 a b b a = b 1.000 m 1 6x 1.012 m 2 Adjust value "a". 3 Approve value "a". 0.625 m 4 Adjust value "b&...
Page 15 - Smart Horizontal Mode
Leica DISTO TM E7400x 788480a 14 EN Measuring Functions Smart Horizontal Mode 1 Aim laser at tar-get. 2 0.032 m 5.204 m 40.8 ° 4.827 m x z x yz y 3 (up to 360° and a transverse tilt of ±10°) i Press key again to switch off horizontal measure-ment. Height tracking i This function displays continously...
Page 16 - Delete Memory; Memory is completely deleted.
Leica DISTO TM E7400x 788480a 15 EN Measuring Functions Memory (20 last displays) Delete Memory 8.294 m 20 20 last displays are displayed. 1 8.294 m 20 Navigates trough 20 last displays. 2 The value from the main line can be used for fur-ther calculations. 2 sec 3 2 sec simultaneously Memory is comp...
Page 17 - Calibration; Calibration of tilt sensor (Tilt Calibration); Place device on absolutely flat surface.
Leica DISTO TM E7400x 788480a 16 EN Calibration Calibration of tilt sensor (Tilt Calibration) 1 2 sec simultane- ously 2 Place device on absolutely flat surface. 3 180° 4 Turn the device horizontally by 180° and place it again on absolutely flat surface. 5 6 Place device on absolutely flat surface. ...
Page 18 - Technical Data
Leica DISTO TM E7400x 788480a 17 EN Technical Data * applies for 100 % target reflectivity (white painted wall), low background illumination, 25 ºC** applies for 10 to 500 % target reflectivity, high background illumination, - 10 ºC to + 50 ºC*** Tolerances apply from 0.05 m to 10 m with a confidenc...
Page 19 - Message Codes; If the message; Error; does not disappear; appears with a number,; Care; Clean the device with a damp, soft cloth.; Warranty; Areas of responsibility
Leica DISTO TM E7400x 788480a 18 EN Message Codes If the message Error does not disappear after switching on the device repeatedly, contact the dealer.If the message InFo appears with a number, press the Clear button and observe the following instructions: Care • Clean the device with a damp, soft c...
Page 20 - Safety Instructions; Permitted use; Measuring distances; Prohibited use; Using the product without instruction; Hazards in use; Limits of use
Leica DISTO TM E7400x 788480a 19 EN Safety Instructions Permitted use • Measuring distances • Tilt measurement Prohibited use • Using the product without instruction • Using outside the stated limits • Deactivation of safety systems and removal of explanatory and hazard labels • Opening of the equip...
Page 21 - Reorient or relocate the receiving antenna.; Laser classification; Laser Class 2 products:; Labelling
Leica DISTO TM E7400x 788480a 20 EN Safety Instructions FCC statement (applicable in U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-able protection against harmfu...
