La Crosse Technology WS-7078TWC - Manual

Page 2 - TABLE OF CONTENTS; Topic Page; Program Mode; Features

2 TABLE OF CONTENTS Topic Page Inventory of Contents/Additional Equipment 3 About WWVB 4 Quick Set-Up Guide 5 Detailed Set-Up Guide Battery Installation 6 Program Mode Function Keys 7 12/24 hour Time Setting 8 Time Zone Setting 8-9 Daylight Saving Time Setting 9 Time Setting (WWVB & Manual) 10-1...

Page 3 - Instruction manual and warranty card.; Figure 1; Figure 2

3 INVENTORY OF CONTENTS 1. The indoor weather station (Figure 1). 2. One TX4U remote thermo/hygro sensor with mounting bracket (Figure 2). 3. Three each, ½” Philips screws. 4. One strip double-sided adhesive tape. 5. Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not included) 1. Four, ...

Page 4 - remote thermo/hygro sensor; first then into

4 continually measuring every second, of every day, to an accuracy of ten billionths of a second per day. These physicists have created an international standard, measuring a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum. For more information about WWVB please see the NIST webs...

Page 5 - Remote Thermo/hygro Sensor; Press the arrow and slide the battery cover off.; Indoor Weather Station; Replace the battery cover.

5 Note: The Thermo Hygro Transmitter transmits a signal every 3 minutes; after the batteries have been installed, the Weather Station will search for the signal for a duration of 5 minutes. If there is no temperature reading in the OUTDOOR LCD after 5 minutes, make sure the units are within range of...

Page 6 - PROGRAM MODE; shield on the face of the unit. To access; 2 or 24 Hour Time Setting; Press and hold the

6 the time signal (reception is achieved easiest at night), it will display the correct time (factory setting is Eastern time zone). PROGRAM MODE Programming Note: If 30 seconds is allowed to pass, or either the “IN” or the “OUT” buttons are pressed during programming modes the unit will confirm/set...

Page 7 - Time Zone Setting; “SET”

7 2. Press and release the “CH” button to toggle between 12 and 24-hour time. 3. Press and release the “SET” button to confirm the 12/24-hour time setting and to advance to Time Zone Setting. B. Time Zone Setting The default time zone is EST, “-5hr” (Eastern Standard Time), to change this setting: 1...

Page 8 - Time

8 5. Press and release the “SET” button to confirm your selection and advance to the Daylight Saving Time setting. C. Daylight Saving Time(DST) Setting 1. Press and hold the “SET” button for 3 seconds or until “12h” or “24h” flashes in the DATE LCD. 2. Press and release the “SET” button 2 times to r...

Page 9 - Manual Time Setting

9 WWVB search every night between these hours and overrides any manually set time. The WWVB tower icon (appearing in the TIME LCD) will flash when a signal-search is in progress, will remain steady when the signal has been received, and nothing will be displayed in all other situations. If the WWVB ...

Page 11 - Setting the LCD Contrast

11 G. Setting the LCD Contrast Note: There are 8 LCD contrast levels to choose from, “Lcd 0” is the lightest and “Lcd 7” is the darkest. 1. Press and hold the “SET” button for 3 seconds or until “12h” or “24h” flashes in the DATE LCD. 2. Press and release the “SET” button 10 times to reach the LCD c...

Page 13 - B. Weather Tendency Arrows

13 Sunny —indicates that the weather is expected to improve (not that the weather will be sunny). Sun with Clouds —indicates that the weather is expected to be fair (not that the weather will be sunny with clouds). Clouds with Rain —indicates that the weather is expected to get worse (not that the w...

Page 14 - Adding Remote Thermo/hygro Sensors; IV. Minimum and Maximum Temperature Records; “IN”

14 The outdoor temperature and humidity is viewed in the OUTDOOR LCD. When there is more than one remote thermo/hygro sensor unit in operation a “boxed” number will appear to the right of the temperature. This indicates which remote thermo/hygro sensor unit (1, 2, or 3) is currently displaying its d...

Page 16 - B. Snoozing and Stopping the Alarm

16 1. Press and hold the “AL1” button for 5 seconds or until the alarm-time display flashes in the DATE LCD. 2. Press and release the “IN” button to set the alarm hours. 3. Press and release the “OUT” button to set the alarm minutes. 4. Press and release the “AL1” button or wait 15 seconds for the u...

Page 17 - B. Viewing and Operating with Multiple Thermo/hygro; “CH”

17 The WS-7078UF is able to receive signals from as many as 3 different remote thermo/hygro sensors. The remote sensor model(s) that you choose will come with their own set of instructions, follow these instructions for a complete guide to setting up. Following are some brief instructions for the ba...

Page 21 - MAINTENANCE AND CARE INSTRUCTIONS; Do not submerge in water.

21 2) Place remote thermo/hygro sensor closer to display. 3) Be sure all batteries are fresh. NOTE: For problems not solved, please contact La Crosse Technology. MAINTENANCE AND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • Clean d...

Page 23 - La Crosse Technology

23 This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information...

La Crosse Technology WS-7078TWC - Manual

Table of Contents:

Summary

Other La Crosse Technology Models