Jet 723950 - User Manual - manualsarea.com

Page 2 - Warranty and service

2 1.0 Warranty and service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time perio...

Page 3 - Table of contents

3 2.0 Table of contents Section Page 1.0 Warranty and service ..................................................................................................................................... 2 2.0 Table of contents ...................................................................................

Page 4 - Safety warnings

4 3.0 Safety warnings Wear eye protection. Always keep guards in place and in proper operating condition. This sander is intended to be used with wood and wood products only. Use of this sander and a dust collector with metal products is a potential fire hazard. Support the workpiece adequately at a...

Page 5 - SAVE THESE INSTRUCTIONS; About this manual

5 26. Maintain tools with care. Follow instructions for lubricating and changing accessories. 27. Use proper extension cord. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized co...

Page 6 - Specifications

6 5.0 Specifications Model number ............................................................................................................................................ JOSS-S Stock number ............................................................................................................

Page 7 - Setup and assembly; Shipping contents

7 6.0 Setup and assembly The sander main unit requires no assembly. Set-up involves only removing sander from pallet, and installing desired table insert and spindle/sleeve combination. 6.1 Shipping contents Most of the below items can be found on or inside sander cabinet. Some items are shipped in ...

Page 8 - Removal from pallet; Drum and spindle storage; Installing/removing spindles; Small sleeve spindles

8 6.4 Removal from pallet To remove sander from pallet: 1. Open cabinet door and remove accessories. 2. Use ratchet wrench with extended socket to unscrew two bolts securing machine to pallet (Figure 2). 3. Move sander off pallet, with help from an assistant. Figure 2: removal from pallet 6.5 Drum a...

Page 9 - Rubber drums; Installing table insert

9 Figure 5: Spindle and drum mounting 6.6.2 Rubber drums Refer to Figure 5. 1. Position spindle taper (A) into main shaft and hold. 2. Rotate nut (D) clockwise by hand, as viewed from above. Rotate nut until spindle seats (stops turning with nut), then continue rotating nut until it tightens. 3. Pus...

Page 10 - Wrench storage; Electrical connections; Grounding instructions

10 Note: Leveling one insert is sufficient as all inserts are same thickness. Figure 6: mounting table insert 6.8 Wrench storage The provided combination wrench has a magnetic strip, and can be placed against any metal surface. Expose the adhesive on the additional magnetic strip and apply anywhere ...

Page 11 - Voltage conversion; Adjustments; Rubber shields

11 The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. This adapter is not permitted in Canada. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly gr...

Page 12 - Table tilt for bevel sanding; Operations; Operating guidelines

12 8.2 Table tilt for bevel sanding Refer to Figures 11 and 12. 1. Loosen both knobs (A, Figure 11) counterclockwise. To tilt forward (45-degree maximum): 2. Move table by hand to desired angle shown on scale (B). Scale is marked in 5-degree increments. 3. Retighten knobs (A). To tilt backward (15-d...

Page 13 - Safety switch; Safety key; Maintenance; General maintenance

13 9. Sanding sleeve life may be prolonged by reversing it on the spindle to make use of opposite end. Keep fingers clear of sanding sleeve and table insert hole during operation. 9.2 Safety switch Refer to Figure 14. To start sander, push green button (A). To stop sander, push red button (B). Figur...

Page 14 - Troubleshooting JOSS-S Spindle Sander; Replacement Parts

14 11.0 Troubleshooting JOSS-S Spindle Sander Symptom Possible Cause Correction Sander will not start. Sander unplugged from wall or motor. Check all plug connections. Fuse blown, or circuit breaker tripped in service panel. Replace fuse, or reset circuit breaker. Cord damaged. Replace cord. Startin...

Page 15 - JOSS-S Table Assembly – Exploded View

Page 16 - JOSS-S Table Assembly – Parts List

16 12.1.2 JOSS-S Table Assembly – Parts List Index No Part No Description Size Qty 1 ................ SBR30M-62 ............... Spring Pin ................................................................ 5*20L ............................ 1 2 ................ JOSS-S-102 .............. Table ...........

Page 18 - JOSS-S Cabinet Assembly – Exploded View

18 12.2.1 JOSS-S Cabinet Assembly – Exploded View 2 8 2 9 0 1 0 2 0 3 0 4 0 6 0 7 0 8 1 0 1 1 1 2 1 4 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 4 2 3 2 5 2 6 2 7 3 0 3 1 3 2 0 2 0 1 3 3 3 4 3 5 3 6 3 7 3 8 0 9 4 1 4 2 4 0 4 3 2 7 1 3 4 5 4 4 3 9 0 5 3 9 4 7 4 6 4 9 5 0 4 8 5 1

Page 19 - JOSS-S Cabinet Assembly – Parts List

19 12.2.2 JOSS-S Cabinet Assembly – Parts List Index No. Part No. Description Size Qty 1 ................ TS-2210451 .............. Hex Cap Screw ........................................................ M10*1.5P*45L ............... 8 2 ................ TS-2361101 .............. Lock Washer ............

Page 20 - JOSS-S Spindle and Drum Assembly– Exploded View

20 12.3.1 JOSS-S Spindle and Drum Assembly– Exploded View

Page 21 - JOSS-S Spindle and Drum Assembly– Parts List

21 12.3.2 JOSS-S Spindle and Drum Assembly– Parts List Index No. Part No. Description Size Qty 1 ................ JOSS-S-301 ......... Combination W rench .................................................... ...................................... 1 2 ................ JOSS-S-302 ......... Magnet (Lar...

Page 23 - Electrical Connections – JOSS-S Spindle Sander

23 13.0 Electrical Connections – JOSS-S Spindle Sander