Jet 708447 - User Manual - manualsarea.com

Page 2 - Warranty and Service

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authori zed Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service ...

Page 3 - Table of Contents

3 Table of Contents Warranty and Ser vice..........................................................................................................................2 Table of Contents ........................................................................................................................

Page 7 - Unpacking; Shipping Contents; Cabinet Hardw are; Tools Needed for Assembly

7 Unpacking Upon delivery, open s hipping containers and c heck that all parts are in good condition. Any damage should be reported to your distributor and s hipping agent immediately. Before proceeding f urther, read your manual and familiarize yourself thoroughly with assembly, maintenance and saf...

Page 8 - Assembly; Stand Assembly

8 Assembly Stand Assembly Referring to Figure 1: 1. Remove all contents from the shipping container. 2. Clean all r ust protected s urfaces with a mild solvent. Do not use paint or lacquer t hinner, gasoline, or mineral spirits; these will damage painted surfaces. 3. Attach t he four rubber pads (A)...

Page 9 - Sanding Belt Installation

9 Referring to Figure 3: 4. The sanding platen (A) is presently in the horizontal pos ition. Pull lock handle (B) forward to unlock the platen assembly. 5. Tilt sanding platen to the vertical position (C), whic h will look like D in Fig. 4; then pus h the lock handle (B) to lock the platen assembly ...

Page 11 - Electrical; Grounding Instructions

11 Electrical Grounding Instructions This sander must be grounded while in use to protect the operator from electric shock. In t he event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped wit ...

Page 12 - Extension C ords; Adjustments; Sanding Platen Angle Adjustment

12 Extension C ords Make sure your extens ion c ord is in good condition. When us ing an extension cord, be s ure to use one heavy enough to carry the c urrent your mac hine will draw. An undersized cord will caus e a drop in t he line voltage res ulting in power loss and over heating. Table 1 s how...

Page 15 - Basic Operations; Horizontal Sanding

15 Basic Operations Removing the belt guard exposes more of the sanding belt! Replace the belt guards immediately after completing any sanding that requires its removal! Failure to comply may cause serious injury! Horizontal Sanding For horizontal sanding , the platen is locked in the horizontal pos...

Page 16 - Contour Sanding

16 Contour Sanding Referring to Figure 19: Contour sanding is done from the extens ion table mounted on the motor where the sanding belt wraps around t he drive drum (D). To set up the sander for contour sanding: 1. Loosen the two lock knobs (C) that secure the drum guard & dust port (E). 2. Swi...

Page 17 - Troubleshooting Operating Problems; Parts; Ordering Replacement Parts

17 Troubleshooting Operating Problems Trouble Possible Cause Solut ion Sander will not start 1. Sander unplugged from wall or motor 2. Fuse blown or circuit breaker tripped 3. Cord damaged 1. Check all plug connections 2. Replace f use or reset circuit breaker 3. Replace cord Sanding belt does not c...

Page 18 - Table and Motor – Assembly

Page 19 - Table and Motor – Parts

19 Table and Motor – Parts Index No. Part No. Descript ion Size Qty. 1 .............. EHVS80CS-01.........Base .................................................................................................. 1 2 .............. EHVS80-02N ...........Pus h Button Switch ................................

Page 21 - Idle Drum – Assembly

Page 22 - Idle Drum – Parts

22 Idle Drum – Parts Index No. Part No. Descript ion Size Qty. ................ OES80CS-IDRA ......Idle Drum Complete Assembly (inde x # 1-72) ......................................... 1 1 .............. OES80CS-201 .........Tens ion Bar .................................................................

Page 24 - Wiring Diagram