Page 2 - Contents
i CV700A / CV702A CHAPTER 1 GENERAL INFORMATION ........................................................................ 1 1-1 MAJOR FEATURE........................................................................................................ 21-2 SPECIFICATION .......................................
Page 3 - ii; CHAPTER 4 INTRODUCTION OF BIOS
ii 3-14 DC +5/+12V OUTPUT CONNECTOR.......................................................................3-15 SERIAL ATA ..............................................................................................................3-16 I C BUS CONNECTOR ................................................
Page 5 - General lnformation
1 The CV700A is a Light form factor All-In-One Multimedia control Board. The board designcombines all necessary input and output effects interfaces, which makes itself an idealall-in-one control board for Networking Application. The board is designedwith 400 MHz internal bus clock rate architecture....
Page 8 - -3 Hardware Notice Guide
4 1-3 Hardware Notice Guide 1. Before installing the power supply with this motherboard, please attach the 12V/DC ( 4 pin connector )of the adapter to motherboard first. After that, plug the adapter power to AC outlet. Always normally shut down the computer before you move the system unit or remove ...
Page 11 - connectors & golden finger direction, and realign the card.
7 Notices: 1.The connectors are designed to ensure the correct insertion. If you feel resistance, check the connectors & golden finger direction, and realign the card. 2. Make sure the retaining clips (on two sides of the slot) lock onto the notches of the card firmly.
Page 14 - Hardware Installation; carefully. Please follow the jumper setting procedure.; -1 Unpacking Precaution; You should follow these
10 Hardware Installation This chapter provides the information how to install the hardware of CV700A. Please follow section 1-4, 2-1 and 2-2 to check the delivery package and unpack carefully. Please follow the jumper setting procedure. Chapter-2 2-1 Unpacking Precaution The CV700A board has been we...
Page 15 - -2 Unpacking checkup
11 2-2 Unpacking checkup First of all, please follow all necessary steps of section 2.1 to protect CV700A from electricity discharge. With reference to section 1.3, please check the delivery package again with following steps: 1. Unpack the CV700A board and keep all packing material, manual and driv...
Page 21 - please check if the DRAM is installed properly or not.; JCF1: CF card mast and slave select
17 NOTE! When you install DIMM module fully into the DIMM socket, the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides. WARNING! 2. Once you hear " Beep Beep Beep" sounds after turning on the power , please check if the DRAM is installed pr...
Page 22 - -8 Jumper Setting Description
18 A jumper is ON as a closed circuit with a plastic cap covering two pins. A jumper is OFF as an open circuit without the plastic cap. Some jumpers have three pins, labeled 1, 2, and 3.You could connect either pin 1 and 2 or 2 and 3.The below figure 2.2 shows the examples of different jumper settin...
Page 23 - Note: Do not clear CMOS unless; Power Voltage select; JCF2 Description; We use to refer to as pin1
19 Note: Do not clear CMOS unless 1. Troubleshooting2. Forget password3. You fail over-clocking system 2-10 JCF2 CF Card Power Voltage select JCF2 Description *1-2 *For CF CARD power voltage select +5V 2-3 For CF CARD power voltage select +3.3V JB1 Description *1-2 *Normal Set 2-3 CMOS Data clear * ...
Page 24 - -11 JCF1 CF Card Master and Slave selection; JCF1 Description
20 2-11 JCF1 CF Card Master and Slave selection JCF1 Description *1-2 *CF Card use Master type 2-3 CF Card use Slave type If you use CF card and HDD together, please set CF as Master and HDD as Slave. JCF1 Master * 1 2 3 1 2 3 Slave
Page 29 - -5 Parallel Port Connector; be disabled through the BIOS SETUP (see Chapter 4)
25 3-5 Parallel Port Connector Parallel Port connector is a D-type 25-pin female connector. The On-board Parallel Port can be disabled through the BIOS SETUP (see Chapter 4) . CN10: Printer (LPT)Port ---CN10 D-SUB 25 PIN PIN NO. Description PIN NO. Description 1 STROBE# 14 AUTO FROM FEED# 2 DATA0 15...
Page 30 - -6 Serial Port Connector; serial port can be disabled through BIOS SETUP (see Chapter 4).
26 3-6 Serial Port Connector The CV700A board offers two high speed NSI6C550 compatible UARTS with Read/ Receive 16 byte FIFO serial ports. The serial ports are two DB-9 external connectors. The On-board serial port can be disabled through BIOS SETUP (see Chapter 4). PIN NO. Description PIN NO. Desc...
Page 31 - -7 Keyboard and Mouse Connector
PIN NO. Description 1 MS DATA 2 NC 3 GND 4 +5V 5 MS CLOCK 6 NC 27 3-7 Keyboard and Mouse Connector CN5: PS2 Keyboard down side (Din 6 pin jack) PIN NO. Description 1 KB DATA 2 MS DATA 3 GND 4 +5V 5 KB CLOCK 6 MS CLOCK CN5: PS2 Mouse up side (Din 6 pin jack) CN5PS/2 Mouse CN5PS/2 Keyboard JKM1: 6 PIN...
Page 32 - CN27: USB port 4 Type A jack
28 3-8 USB Port/ Header CN3 (Down side) : USB 0/1port Type A Jack PIN NO. Description 1 +5V 2 USB DATA 0/1- 3 USB DATA 0/1+ 4 GND JUSB1/JUSB2 USB 4/5 port 5pin header (2.54mm) PIN NO. Description 1 +5V 2 USB DATA 6/7- 3 USB DATA 6/7+ 4 KEY5 GND pin1 JUSB2 CN27 CN27: USB port 4 Type A jack PIN NO. De...
Page 34 - LAN Led; Back side connector
30 3-11 LAN Port The Fast Ethernet controller provides 32-bit performance, PCI bus master capability, and full compliance with IEEE 802.3 10/100Based-T specification. For 10/100Base-T operation, please connect the network connection by plugging one end of the cable into the RJ-45 jack of the CN9,CN8...
Page 35 - -12 Audio Port Connector
31 3-12 Audio Port Connector The CV700A has an on-board AC'97 3D sound interface. There are the connectors of LINE OUT, MIC-IN and CD-IN connectors.The MIC-IN Jack and CD-IN header are for audio sound input. The LINE-OUT connector is a 4-pin Jack for audio sound output. PIN NO. Description 1 GND 2 F...
Page 37 - -16 I C Bus Connector
33 3-15 Serial ATA PIN NO. Description 1 GND 2 DATA TX+ . SATA1: S-ATA IDE 7pin Wafer SATA1 3 DATA TX- 4 GND 5 DATA RX- 6 DATA RX+ 7 GND PIN NO. Description 1 +3.3V 2 GND 3 I2C CLK 4 I2C DATA . CN26: I C Bus connector 4pin (1.25mm Wafer connector) 2 3-16 I C Bus Connector 2 pin1 CN26
Page 38 - . LAN LED Activity LED; LAN1/ LAN2 LED shows the activity of network
34 3-18 Front-Panel . JR1: System Reset key( 2.0mm pin header) . Power switch: PW-ON--- SW1 JSW1: Power on switch Based on case design , there may be a power switch or a 2-pin header connected to the case-mounted power switch. It is used to power ON/OFF the system. . Power LED: PW-LED / JP1 The Powe...
Page 39 - Chapter 4; Introduction of BIOS
35 The BIOS is a program located in the Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gains control. The BIOS first operates an auto-diagnostic test called POST (Power on Self Test) for all the necess...
Page 40 - Main Menu; bottom of the screen.
36 4-2 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu/ Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highl...
Page 42 - This menu is to set User and Supervisor Passwords.; Exit Without Saving; Abandon all the CMOS values modified and exit setup.; -4 Standard CMOS Features; the value you want to modify with this item.
[ EGA/VGA] 38 Load Standard Defaults Use this menu to load the BIOS default values for the optimum system performance. Standard Defaults settings are relatively more reliable than Optimized Defaults. All the product verifications, compatibility test reports and manufacture quality controls are based...
Page 43 - -5 Advanced BIOS Features; Virus Warning; (default) No warning message appears when anything attempts to; Enabled; Activate automatically when the system boots up. The system
39 4-5 Advanced BIOS Features Virus Warning The VIRUS Warning feature can help you protect IDE Hard Disk boot sector. If this function is enabled, BIOS will show a warning message on screen and alarm beep when somenoe attemps to write data into this area without permission. Disabled (default) No war...
Page 44 - -6 Advanced Chipset Features; correct for your system configuration.
40 4-6 Advanced Chipset Features The Advanced Chipset Features Setup option is used to change the values of the chipset registers. These registers control most of the system options in the computer. Ite m He lp DRAM Clock/Drive Control [Press Enter ]AGP & P2P Bridge Control [Press Enter] Mem ory...
Page 45 - -7 Integrated Peripherals
41 4-6-2 AGP & P2P Bridge Control Ite m He lp DRAM Clock/Drive Control [64M ]AGP & P2P Bridge Control [Enabled] Me nu Le vel >> ↑↓→ ← :M ove Enter :Sel ect +/- /PU/P D:Va lue F10:S ave ESC:E xit F1:G enera l He lp F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Phoenix- ...
Page 47 - -8 Power Management Setup; IRQ / Event Activity Detect
43 4-7-3 Super IO Device [3F8/IRQ4] Phoenix-AwardBIO S CMOS Setup Utility Super IO Device Ite m He lp Onboard Serial Port 1 M enu L evel >> ↑↓→ ← :M ove Enter :Sel ect +/- /PU/P D:Va lue F10:S ave ESC:E xit F1:G enera l He lp F5 :Pre vious Val ues F6: Fail-Safe Def ault s F7:Opti mize d De fau...
Page 48 - IRQs Activity Monitoring
44 4-8-1 IRQ / Event Activity Detect 4-8-1.1 IRQs Activity Monitoring IRQs Activity Monitoring Please refer to section4-8-1.1
Page 49 - should make any change to the default settings.; Resource Controlled By; Leave this field at Disabled. The settings are Enabled or Disabled.
4-9 PnP / PCI Configuration Setup 45 This section describes how to configure the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at the speed the CPU itself keeps when CPU communicates with its own special components. This section covers some v...
Page 50 - -10 PC Health Status; This section shows the status of your CPU, Fan, and overall system.; Show PC Health in Post; Enabled or Disabled
46 4-10 PC Health Status This section shows the status of your CPU, Fan, and overall system. This is only available when there is Hardware Monitor function onboard. Show PC Health in Post During Enabled, it displays information list below. The choice is either Enabled or Disabled Current CPU Tempera...
Page 51 - This section is to set CPU Frequency Control.; Auto Detect DIMM/PCI Clock; The settings are Enabled or Disabled.; Spread Spectrum; This item allows you to set the CPU Host/PCI clock Spread Spectrum.; Load Standard Defaults; system operation performance.
47 4-11 Frequency/Voltage Control This section is to set CPU Frequency Control. Auto Detect DIMM/PCI Clock This item allows you to enable or disable Auto Detect DIMM/PCI Clock. The settings are Enabled or Disabled. Spread Spectrum This item allows you to set the CPU Host/PCI clock Spread Spectrum. T...
Page 53 - Chapter 5; DRIVER INSTALLATION; needed so that your system can function properly.; From MAGIC INSTALL MENU you may make 3 selections:; . Auto detect main board and OS Into auto install driver Menu
49 Chapter 5 DRIVER INSTALLATION There is a SYSTEM INSTALL CD disk in the package. This CD has all the drivers you need and some free application programs and utility programs. In addition, this CD also includes an auto-detect software which can tell you which hardware is installed and which driver ...
Page 54 - Auto install driver Menu
50 Auto install driver Menu 1. VIA 4 IN 1 install VIA IDE/AGP/IRQ ROUTING/INF driver 2. VGA install on-board VGA driver 3. SOUND install AC97 Audio Codec Installing driver 4. USB2.0 install VIA USB2.0 hardware Installing driver 5. LAN to LAN install driver readme file 6. DIRECTX9 To install DirectX9...
Page 55 - TL
51 1.Click VIA 4 IN 1 when System Install MENU appears. 2.Click NEXT when VIA Service Pack Wizard appears. 3.License Agreement. Click NEXT. 4. Choose all the drivers. Click NEXT. Note: VIA AGP Driver IS TO BE INSTALLED UNDER WIN98 ONLY. 5-1 VIA 4 IN 1 Install VIA IDE/AGP/ INF Driver IDE : VIA ATAPI ...
Page 57 - -2 VGA INSTALL CN700 VGA Driver
53 1. Click VGA when System Install MENU appears. 2. Click NEXT when VIA/S3 CN700 Driver Setup appears. 5-2 VGA INSTALL CN700 VGA Driver 3. This VIA/S3 CN700 Driver install willbegin copying the driver files. Click NEXT. Note: When you install driver ,the “Hardware Installation”dialog in Windows XP ...
Page 58 - Click NEXT install VIA AC97 Audio Driver; -3 SOUND Install VIA Audio Codec Driver for VIA
54 1.Click SOUND when System Install MENU appears. 2. Click NEXT install VIA AC97 Audio Driver 5-3 SOUND Install VIA Audio Codec Driver for VIA 3. Click NEXT install VIA AC97 Audio Driver 4. Click FINISH to Restart Computer. NOTE: The path of the file For WIN98/ME/2K\XP X:\ driver\via\viaudio\setup....
Page 60 - -6 HOW TO UPDATE BIOS
56 5-5 HOW TO DISABLE ON-BOARD SOUND Enter BIOS SETUP. Choose INTEGRATE PERIPHERALS. Choose On-Chip Device FUNCTION. Choose " AC97 Audio Disable " on-board sound function by pressing PAGE DOWN KEY to Disable. In DOS Mode STEP 1. Prepare a boot disc. (you may make one by clicking START, click...
Page 61 - Appendix A: Power Consumption Test; Condition; Start up; The power consumption depends on your device choice!; Appendix B: Resolution list
57 Appendix A: Power Consumption Test Condition Item Spec CPU V4 - C7 1GHz DDR RAM DDR2 533/1GB Operating System Windows XPP/SP2 Test Program 3D Mark 2001SE HDD 3.5" Standard HDD HDD 2.5" Slim Type HDD Mini PCI Card Wireless LAN IEEE802.11g Hard Disk Stand by Standard HDD 0.10A Slim Type HDD...
Page 62 - Fanless solution with HDD
58 Warning ! 1. CF card & 2.5” HDD first boot issue Due to the frequent update and change of Compact Flash card, it can’t always work with 2.5” HDD at the same time. Users may try and get the test result. 2. Batter y Battery on board is consumables. Lex doesn’t guarantee the life time of it. 3. ...
