Page 2 - Specifications
2 Specifications The Notebook Computer is a state-of-the-art, high performance, portable system. It offers a host of features specially designed to enhance performance and usability. l CPU ü Intel P54C ü Intel P54LM ü Intel P55C with MMX technology. l Memory ü 3.3 V power supply. ü Supports Fast Pag...
Page 4 - System Memory Map
4 I/O Address Map Hex range Device 000 - 00F DMA controller-1 020 - 021 Interrupt controller-1 040 - 043 Timer 1 048 - 04B Timer 2 060 - 06E KB controller M38813 chip select 070 - 071 RTC and NMI mask 080 - 08F DMA page register 0A0 - 0A1 Interrupt controller-2 0C0 - 0DF DMA controller-2 1F0 - 1F7 F...
Page 5 - Motherboard
5 Motherboard The motherboard is designed mainly based on Pentium CPU and the OPTi FireStar 82C700 chipset; it includes the following features: * OPTi 82C700 chipset solution from OPTi * C&T 65554 Multimedia Flat Panel Controller * PCI Local Bus IDE interface * SMC669FR super I/O Floppy Disk Con...
Page 6 - Microprocessor
6 Microprocessor P54C Pentium-100 Microprocessor The Intel Pentium Microprocessor is a 64-bit architecture with on chip Memory Management Unit (MMU), floating point (math coprocessor) and cache memory (16K bytes, code and data caches each contain 8 Kbytes of information) units. It has the same funct...
Page 7 - Chips; Core Logic Chip - OPTi FireStar 82C700
7 Chips Core Logic Chip - OPTi FireStar 82C700 l Support for Intel 586 CPU with bus speed up to 66MHz l Support for both symmetric and asymmetric type DRAM l High Performance Memory Controller l Enhanced hidden refresh l Support for Fast Page mode, EDO type. l Supports two bus mastering IDE channels...
Page 9 - DRAM Speed
9 PC CARD 95 (CardBus) Interface Controller - TI PCI1131 TI CardBus Interface Controller 1131 implements the PCMCIA 2.0/JEIDA 4.1 standard. It contains the following functions: l PCI interface Specification 2.1 l Supports Zoom Video Mode l PCMCIA dual-socket interface l Five programmable memory wind...
Page 10 - Super I/O Floppy Disk Controller - SMC FDC669FR
10 Super I/O Floppy Disk Controller - SMC FDC669FR l Intelligent Auto Power Management l 16 Bit Address Qualification (Optional) l 2.88MB Super I/O Floppy Disk Controller ü Support Vertical Recording Format ü 16 Byte Data FIFO ü Enhanced Digital Data Separator. Data rate up to 1Mb/s. l Multi-Mode Pa...
Page 11 - AIT1108E VGA to NTSC/PAL Converter; Keyboard Controller - Mitsubishi M38813M4
11 AIT1108E VGA to NTSC/PAL Converter l Converts VGA source analog RGB into broadcast-quality NTSC or PAL video signal. l Multiple output standards - NTSC, PAL. l S-Video output format. Real PCI To USB (OHCI) Chip - CMD0670 l Complies with OpenHCI 1.0,USB 1.0,and PCI Local Bus 2.1 specifications. l ...
Page 13 - Interfaces; Floppy Disk Drive Interface
13 Interfaces Floppy Disk Drive Interface Pin Description Pin Description 1 VCC 29 N.C 2 VCC 30 N.C 3 MTR0# 31 N.C 4 INDEX# 32 N.C 5 3MOD 33 N.C 6 FDD0# 34 N.C 7 TRK0# 35 N.C 8 DSKCHG# 36 N.C 9 HDSEL# 37 GND 10 DIR# 38 GND 11 RDATA# 39 N.C 12 STEP# 40 N.C 13 WRPRT# 41 N.C 14 WDATA# 42 N.C 15 WGATE# ...
Page 14 - Hard Disk Drive Interface
14 Hard Disk Drive Interface The Notebook PC has a standard PC/AT interface (IDE) which can directly interface with any hard disk drive with an embedded controller supporting the same PC/AT interface through the use of a 56-pin B/B connector. The 56-pin connector has the following pin configurations...
Page 16 - Expansion Memory Socket
16 Expansion Memory Socket The Notebook PC has two 144-pin SODIMM type Expansion memory s ockets with the following pin configurations: Socket 1: Pin Description Pin Description Pin Description 1 GND 2 GND 3 MD0 4 MD32 5 MD1 6 MD33 7 MD2 8 MD34 9 MD3 10 MD35 11 MEM-VCC 12 MEM-VCC 13 MD4 14 MD36 15 M...
Page 18 - Docking Connector Pin Assignment
18 Docking Connector Pin Assignment Pin Description Pin Description Pin Description 1 A + 2 A + 3 CCO 4 SOUTA 5 GND 6 /DCD2 7 /DSR2 8 SIN2 9 /RTS2 10 GND 11 /STROBE 12 /AUTOFD 13 PPD0 14 /ERROR 15 PPD1 16 /INIT 17 PPD2 18 GND 19 SLCT 20 D-LOCK 21 CCLK3 22 GND 23 CCLK2 24 GND 25 CCLK1 26 GND 27 CCLK0...
Page 19 - Internal Trackpad Interface; External Monitor Interface; RGB Out
19 Internal Trackpad Interface There is a 8-pin connector used to interface with the internal trackpad. It will be disabled when external mouse has been installed. The trackpad is hardware-connected to PS/2 port, hardware-compatible to Microsoft PS/2 mouse and software-compatible to Microsoft mouse ...
Page 21 - External USB (Universal Serial Bus) Interface
21 External USB (Universal Serial Bus) Interface Port A: Pin Description 1 V1+OUT 2 VD1-N 3 VD1-P 4 GND Port B: Pin Description 1 V2+OUT 2 VD2-N 3 VD2-P 4 GND
Page 22 - Internal ISA Interface (For; Optional
22 Internal ISA Interface (For Optional Modem/LAN) Pin Description Pin Description 1 RSTDRV 31 MODEM 2 SD0 32 SD1 3 SD2 33 SD3 4 SD4 34 SD5 5 SD6 35 SD7 6 SD8 36 SD9 7 SD10 37 SD11 8 SD12 38 SD13 9 VCC 39 VCC 10 SD14 40 SD15 11 SMEMR# 41 IOCHRDY 12 IO16# 42 +12V 13 IORD# 43 AEN 14 IOWR# 44 IRQ10 15 ...
Page 24 - PCMCIA CardBus Interface
24 PCMCIA CardBus Interface Socket A: Pin Description Pin Description 1 GND 35 GND 2 A-CD3 36 A-CD1# 3 A-CD4 37 A-CD11 4 A-CD5 38 A-CD12 5 A-CD6 39 A-CD13 6 A-CD7 40 A-CD14 7 A-CE1# 41 A-CD15 8 A-CA10 42 A-CE2# 9 A-OE# 43 A-VS1 10 A-CA11 44 A-IORD# 11 A-CA9 45 A-IOWR# 12 A-CA8 46 A-CA17 13 A-CA13 47...
Page 28 - DC/DC Converter Board
28 DC/DC Converter Board The Notebook PC has a built-in DC/DC converter module which provides all the DC voltage outputs required by the system. This module will have the following features: A. Input requirements : - Voltage input from AC adapter : 20.0V - Voltage input from battery : 12.0V (Ni-MH),...
Page 29 - CPU Power Board
29 CPU Power Board The module provides special CPU which voltage is adjustable (from 1.5V - 3.1V), This module will have the following features : A. Input requirement : - Voltage input from AC adapter :+20V. - Voltage input from battery :+12V (Ni-MH), or +10.8V (Li-Ion) B. Output requirement : Volta...
Page 30 - Inverter Board
30 Inverter Board The Notebook PC has a built-in inverter module which provides all the requirements to support the DSTN color and TFT color panels. This module will have the following features: DC input : 8V ~ 21V full range AC output: Item Min. Typical Max. Input voltage (V) 8 21 Input current (A)...
Page 31 - Setting DIP Switch
31 Setting DIP Switch Locate the DIP Switch (SW1) to set the correct configuration for the following purposes: l Flash ROM BIOS Update. l CPU upgrade. l Cache mode (reserved). Dip Switch (SW1) Purpose SW1-1 SW1-2 Flash ROM BIOS Off Off Existing BIOS On On Updating BIOS SW1-5 SW1-6 SW1-7 SW1-8 CPU Sp...
Page 32 - POST Checkpoint Codes; Uncompressed Initialization Codes; Bootable Recovery Codes
32 POST Checkpoint Codes POST is performed by the BIOS when the computer is reset or booted. POST tests and initializes key components. When a POST routine completes, a code is written to I/O port address 80h. Display this code by attaching diagnostic equipment to I/O port address 0080h. Uncompresse...
Page 33 - Power On Self Test; POST Phases; BIOS Error Reporting
33 Power On Self Test POST Phases Every time the system is power on, BIOS executes two types of POST routines: System Test and Initialization Test and initialize BIOS for normal operations. System Configuration Verification Compare defined configuration with hardware actually installed. BIOS Error R...
