Impex WM 1403 - Manual - manualsarea.com

Page 2 - Toll-Free Customer Service Number

TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICE...................................................................……….. 2 HARDWARE IDENTIFIER.....…......................................................

Page 3 - IMPORTANT SAFETY NOTICE

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precau...

Page 6 - DIAGRAM 2

STEP 2 (See Diagram 2) A.) Attach the Front Upper Vertical Beam (#5) to the Front Lower Vertical Beam (#82). Secure it with two M10 x 2 ½” Carriage Bolts (#42), ∅ ¾” Washers (#53), and M10 Aircraft Nuts (#55). DIAGRAM 2 5

Page 7 - DIAGRAM

STEP 3 (See Diagram 3) A.) Attach the Front Lower Vertical Beam (#82), both Left and Right Storage Posts (#15) & (#16) to the Main Base Frame (#6). Secure them together with two M10 x 3” Carriage Bolts (#73), ∅ ¾” Washers (#53) and M10 Aircraft Nuts (#55). Do not tighten the nuts and bolts yet. ...

Page 8 - DIAGRAM 4

STEP 4 (See Diagram 4) A.) Slide the Weight Holder (#2) onto the Rear Vertical Beam (#1) from the top. B.) Attach the rear end of Upper Frame (#4) to the Rear Upper Vertical Beam (#1). Secure the upper hole with a Small Bracket (#20), M10 x 2 3/8” Allen Bolt (#46), and ∅ ¾” Washer (#53). Sure the bo...

Page 9 - DIAGRAM 5

STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#12) to the Upper Frame (#4). Secure it with one 5 7/8” Axle (#60), two ∅ 1” Axle Washers (#64), and two M10 Aircraft Nuts (#55). Do not over tighten the nuts. Make sure the Base is able to swivel. B.) Attach the Front Press Stopper (#8) and Bu...

Page 10 - DIAGRAM 6

STEP 6 (See Diagram 6) A.) Attach a Rubber Bumper (#38) to the Leg Developer (#11). Secure it with one M6 x 5/8” Philips Screw (#41). Attach the Leg Developer to the bracket on the Main Seat Support (#7). Secure it with one M10 x 3” Allen Bolt (#44), two ∅ ¾” Washers (#53), and one M10 Aircraft Nut ...

Page 12 - Cable Loop Diagram

Page 14 - Diagram 8

Page 15 - DIAGRAM 9

STEP 9 (See Cable Loop Diagram & Diagram 9) A.) Attach one end of the 116” Butterfly Cable (#29) to the Hook on the Right Butterfly Arm (#14). Pull the Cable to the Butterfly Pulley Bracket (#10). Attach a Pulley (#28) to the Bracket (#10). Secure it with one M10 x 1 ¾” Allen Bolt (#45), two ∅ ¾...

Page 21 - WEIGHT RESISTANCE CHART

WEIGHT RESISTANCE CHART The following chart shows the approximate weight resistance ratio at each station. Weight resistance shows for the butterfly station is for each butterfly arm. The actual resistance at each station may vary due to friction and differences in each individual plate . Weight Pla...

Page 22 - LIMITED WARRANTY

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's...

Impex WM 1403 - Manual

Table of Contents:

Summary

Other Impex Models