Impex MSS-1600 - Manuals - manualsarea.com

Page 2 - Thank you for selecting the SA GEAR HOME GYM MSS-1600 by IMPEX; Toll-Free Customer Service Number

TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................

Page 3 - IMPORTANT SAFETY NOTICE; PRECAUTIONS

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precau...

Page 4 - WARNING LABEL REPLACEMENT

WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3

Page 5 - HARDWARE PACK

HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4

Page 10 - Securely tighten all Nuts and Bolts installed in Step-1 and Step-2.

STEP 2 (See Diagram 2) A.) Slide 9 Weight Plates (#29) onto the Guide Rods (#5). Make sure the deep groove on the W eight Plates all face the back of the machine and downward. Align the holes on the W eight Plates. Insert a Selector Rod (#14) through the center hole. Use a W eight Selector Pin (#36)...

Page 12 - Do not over tighten the Bolt and Nut.; DIAGRAM 3

A.) Attach the Seat Support (#9) to Vertical Frame (#3). Secure it with two M10 x 2 3/8” Carriage Bolts (#61), one 5 1/8” Curved Bracket (#22), two Ø ¾” Washers (#74), and two M10 Aircraft Nuts (#76). B.) Place the Seat (#26) onto the Seat Support. Secure it with two M8 x 2 1/8” Allen Bolts (#71) an...

Page 13 - Do not over tighten the Nuts. Make sure the Front Press Base

A.) Attach two Ø 1” Bushings (#41) to the holes on Upper Frame (#4). Attach the Front Press Base (#6) to the Bushings. Secure it with one M12 x 4 ½” Allen Bolt (#62), two Ø 1” Washers (#75), and one M12 Aircraft Nut (#67). Do not over tighten the Nuts. Make sure the Front Press Base can move freely....

Page 14 - DIAGRAM 4

Page 17 - DIAGRAM 5

Page 20 - DIAGRAM 7

Page 21 - DIAGRAM 8

STEP 8 (See Diagram 8) A.) Attach the weight Stack Cover (#23) to Main Base Frame (#1) and Upper Frame (#4). Secure the Cover with five M10 x 5/8” Allen Bolts (#64) and five Ø ¾” Washers 9#74). B.) Attach the Lat Bar (#17) to Upper Cable (#32) with a 10-link Chain (#34) and two C-clips (#35). DIAGRA...

Page 23 - PARTS LIST; DESCRIPTION

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Base Frame 1 51 Ø 1 ¾” Rubber Bumper 1 2 Rear Stabilizer 1 52 Sleeve 1 3 Vertical Frame 1 53 1 5/8” x 3 1/8” End Cap 3 4 Upper Frame 1 54 Ø 1 ¾” End Cap 2 5 Guide Rod 2 55 Ø 2” End Cap 4 6 Front Press Base 1 56 Ø 1” Con-shaped End Cap 1 7 Left Butterfly 1 5...

Page 24 - MSS-1600 WEIGHT RESISTANCE CHART; Numbers are approximate. Actual weights may vary.

MSS-1600 WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Front Press 30 42 54 66 78 90 102 114 126 Butterfly 15 20 25 30 35 40 45 50 55 Lat Pull 30 40 50 60 70 80 90 100 110 Low Pulley 30 40 50 60 70 80 90 100 110 Leg Developer 30 40 50 60 70 80 90 100 110 Note: Each plate weights 10 ...

Page 25 - LIMITED WARRANTY

IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IM...