Impex TR-2 - Manual - manualsarea.com

Page 2 - WARNING LABELS PLACEMENT

WARNING LABELS PLACEMENT The Warning Labels shown here have been placed on Lower Pulley Support Base. If this Labels are missing or illegible, please call Customer Service at 1-800-999-8899 for free replacement. Apply the Label in the location shown.

Page 3 - TABLE OF CONTENTS; please call our; Toll-Free Customer Service Number

TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…..............................................................

Page 4 - IMPORTANT SAFETY NOTICE

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precau...

Page 5 - HARDWARE PACK

Page 6 - ASSEMBLY INSTRUCTION

ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Base Platform (#8) on flat surface. Attach the Vertical Fr...

Page 7 - DIAGRAM 2

STEP 2 (See Diagram 2) A.) Attach the lower Rear Support Frame (#2) to the Base Platform (#8). Secure it with one M10 x 4 7/8” Hex Bolt (#13), Ø ¾” Washer (#10), and M10 Aircraft Nut (#16). DO NOT tighten the Nut and Bolt yet. B.) Insert bottom of Lower Pulley Support Base (#45) into the openings on...

Page 8 - DIAGRAM 3

STEP 3 (See Diagram 3) A.) Attach the High Pulley Support Bar (#18) to the Upper Frame (#17). Securely tighten with one Bracket (#19), two M10 x 2 3/8” Hex Bolts (#20) and two Ø¾” Washers (#10). Cover the two Hex Bolts with two M10 Nut Caps (#21). B.) Attach the Upper Frame (#17) to the Vertical Fra...

Page 9 - DIAGRAM 4

STEP 4 (See Diagram 4) A.) Attach the Tech Rod Set (#24) to the Rear Support Frame (#2). Secure it with four Ø 1/4” x ¾” Philips Screws (#25). B.) Slide the Tech Rod Organizer (#23) onto the top of the Rods to hold each Rod in position. DIAGRAM 4 7

Page 10 - DIAGRAM 5

STEP 5 (See Diagram 5) A.) Place the Seat Pad (#27) onto the Seat Support (#26). Secure it with four M6 x ¾” Hex Bolts (#6) and Ø½” Washers (#7). B.) Attach the Seat Support (#26) to the open bracket on the Vertical Frame (#1). Use a Lock Knob (#28) to securely lock the Seat Support in position. DIA...

Page 11 - DIAGRAM 6

STEP 6 (See Diagram 6) A.) Attach the Leg Developer (#30) to the front of Seat Support (#26). Secure it with one M10 x 3” Hex Bolt (#12), two Ø¾” Washers (#10), and one M10 Aircraft Nut (#16). B.) Cover the Nut and Bolt with two M10 Nut Caps (#21). Cover the Nuts on the Cable Roller (#44) with two M...

Page 12 - DIAGRAM 7

STEP 7 (See Diagram 7) A.) Insert a Foam Tube (#32) halfway through the hole on the Seat Support (#26). Insert a Foam Tube halfway through the hole on the Leg Developer (#30). B.) Push four Foam Rolls (#33) onto the Foam Tubes from both ends. Plug four Foam Roll End Caps (#34) into the ends of the T...

Page 13 - DIAGRAM 8

STEP 8 (See Diagram 8 & Lat Bar Cable Loop Diagram) A.) Follow the below instructions to use the Lat Bar. B.) Attach a Tech Rod Cable (#11) to the Right Pulley on the Extension Tube (#43). Attach the other end, L Shaped Connector (#41) to one of the Tech Rod. C.) Attach one 57” Lat Cable (#35) t...

Page 14 - LAT BAR CABLE LOOP DIAGRAM

Page 15 - DIAGRAM 9

STEP 9 (See Diagram 9 & Leg Developer Cable Loop Diagram) A.) Follow the below instructions to use the Leg Developer. B.) Detach the end of the Lat Bar Cables from the End Hooks on Tech Rod Cables and hook the Cable ends onto the Cable Hangers on the side of the Vertical Frame. C.) Store the Lat...

Page 18 - TECH ROD CABLE LOOP DIAGRAM

Page 19 - EXPLODED DIAGRAM

Page 20 - TECH ROD RESISTANCE CHART

TECH ROD RESISTANCE CHART TECH ROD (each side) Bench Press/ Butterfly LAT CABLE LEG DEVELOPER CABLE 5LB 5 LB 5 LB 3 LB 10LB 10 LB 10 LB 8 LB 10LB 10 LB 10 LB 8 LB 25LB 25 LB 25 LB 20 LB 50LB 50 LB 50 LB 35 LB TOTAL 100LB 100LB 74LB *Numbers are approximate. Actual resistance may vary. *Value is for ...

Page 22 - LIMITED WARRANTY

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's...

Impex TR-2 - Manual

Table of Contents:

Summary

Other Impex Models