Impex MWB-4360 - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS; Thank you for selecting the MARCY; Toll-Free Customer Service Number

TABLE OF CONTENTS BEFORE YOU BEGIN..................................................................……………. 1 IMPORTANT SAFETY NOTICES.................................................................… 2 SMITH MACHINE HARDWARE PACK….......…............................................. 4 SMITH MACHINE ...

Page 3 - IMPORTANT SAFETY NOTICE

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precau...

Page 5 - SMITH MACHINE HARDWARE PACK

Page 7 - DIAGRAM 1

SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Base Frames (#1) by a Cross Brace (#2...

Page 9 - DIAGRAM 2

Page 14 - CABLE LOOP DIAGRAM

Page 19 - DIAGRAM 9

Page 23 - PARTS LIST

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Base Frame 2 55 Sliding Sleeve 8 2 Cross Brace 1 56 Lock Ring 2 3 Front Vertical Beam 2 57 Pulley 10 4 Left Vertical Frame 1 58 Ø 1 ¾” Rubber Bumper 1 5 Right Vertical Frame 1 59 Ø 2 ½” Rubber Bumper 2 6 Rear Vertical Beam 1 60 Spring Clip 10 7 W eight Glide Pos...

Page 24 - MULTI-PURPOSE BENCH HARDWARE PACK

Page 25 - ASSEMBLY INSTRUCTION

MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#1) to the Front &a...

Page 27 - DIAGRAM 3

STEP 3 (See Diagram 3) A.) Place the Backrest Board (#14) onto the Backrest Supports (#7). Secure it with four M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43). B.) Place the Seat Pad (#13) onto the Seat Support Frames (#6). Secure it with four M8 x 2” Allen Bolts (#40) and ∅ 5/8” Washers (#43). D...

Page 28 - DIAGRAM 4

STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Main Frame (#1). Secure it with an Axle (#17), two M10 x ¾” Allen Bolts (#36), and two ∅ ¾” Washers (#42). B.) Insert one Foam Tube (#10) halfway through the hole on the Main Frame. Insert two Foam Tubes halfway thro...

Page 29 - DIAGRAM 5

STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#15) to the Arm Curl Stand (#4). Secure it with two M8 x 5/8” Allen Bolts (#41) and two ∅ 5/8” Washers (#43). Insert the Arm Curl Stand into the front opening on the Main Frame (#1). Use the Lock Knob to hold the desired Arm Curl height. B.) Attach...

Page 32 - MWB-4360 WEIGHT RESISTANCE CHART; Station Ratio; Low Pulley

MWB-4360 WEIGHT RESISTANCE CHART Station Ratio Example Low Pulley 200% 10 lb. plate creates 20 lb. resistance Lat Pull 50% 10 lb. plate creates 5 lb. resistance Butterfly (both arms) 100% 10 lb. plate creates 10 lb. resistance Left Cross-Over 50% 10 lb. plate creates 5 lb resistance Right Cross-Over...

Page 33 - LIMITED WARRANTY

IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IM...

Impex MWB-4360 - Manual

Table of Contents:

Summary

Other Impex Models