Impex MD-11.0 - Manual - manualsarea.com

Page 2 - INC. For your safety and benefit, read this manual carefully; Toll-Free Customer Service Number

TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…..............................................................

Page 3 - IMPORTANT SAFETY NOTICE

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precau...

Page 4 - WARNING LABEL REPLACEMENT

WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer, and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3

Page 5 - HARDWARE PACK

Page 8 - DIAGRAM 1

ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#27) to the Bench Front & Rear Stabi...

Page 9 - DIAGRAM 2

STEP 2 (See Diagram 2) A.) Attach the two side-holes on bottom of Backrest Supports (#30) to the pivot on the Main Frame (#27). Secure it with one M12 x 5 ¾” Allen Bolt (#75), two Ø 1” Washers (#68), and one M12 Aircraft Nut (#71). B.) Align the pivot on top of Backrest Incline Support (#31) to the ...

Page 10 - DIAGRAM 3

STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#33) to the open bracket on the Main Frame (#27). Secure it with one M10 x 3 1/8” Allen Bolt (#76), two Ø ¾” Washers (#69), and one M10 Aircraft Nut (#72). Do not over tighten the bolt and nut, make sure Leg Developer is able to swivel. B.) Insert...

Page 11 - DIAGRAM 4

STEP 4 (See Diagram 4) A.) Attach the Arm Curl Pad (#37) to the Arm Curl Stand (#32). Secure it with two M8 x ¾” Allen Bolts (#84) and two ∅ ¾” Washers (#70). Insert the Arm Curl Stand into the front opening on the Main Frame (#27) and secure it with a Lock Knob (#61) to hold it at the desired heigh...

Page 14 - DIAGRAM 6

Page 15 - CABLE LOOP DIAGRAM

Page 18 - DIAGRAM 9

STEP 9 (See Diagram 9) A.) Attach a Weight Post (#20) to the Right Support (#3). Secure it with a M10 x ¾” Allen Bolt (#81) and Ø ¾” Washer (#69). Slide an Olympic Sleeve (#44) onto the Post. Repeat the same procedure to install the other side. B.) Insert the Left & Right Bar Catches (#15 & ...

Page 20 - RACK EXPLODED DIAGRAM

Page 21 - PARTS LIST

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Upright Beam 2 51 1 ¾” Square End Cap 5 2 Left Support 1 52 2” Square End Cap 2 3 Right Support 1 53 Ø ½” Bushing 2 4 Left Floor Stabilizer 1 54 1” Square End Cap 2 5 Right Floor Stabilizer 1 55 Ø 1” End Cap 1 6 Cross Brace 1 56 Foam Roll End Cap 6 7 Rear Stabil...

Page 22 - LIMITED WARRANTY

IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IM...

Impex MD-11.0 - Manual

Table of Contents:

Summary

Other Impex Models