Impex CR 5 - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS; please call our; Toll-Free Customer Service Number

TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…...........................................................

Page 3 - IMPORTANT SAFETY NOTICE

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precau...

Page 5 - ASSEMBLY INSTRUCTION; Diagram 1

ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Right Base Frame (#46) and Left Base Frame (#87) on the floor, ...

Page 6 - DIAGRAM 2

STEP 2 (See Diagram 2) A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5). B.) Attach the Right Seat Support (#49) to the Right Vertical Beam (#21). Secure it with one Bracket (#7),...

Page 8 - DIAGRAM 3

Page 9 - DIAGRAM 4

STEP 4 (See Diagram 4) A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼” Front Press Axle (#60), two ∅ ¾” Washers (#6), and two M10 Aircraft Nuts (#5). B.) Attach the Front Press Frames (#63) to the Front Press Base. Secure it with four M10 x 2 ¾” Carriage Bo...

Page 10 - DIAGRAM 5

STEP 5 (See Diagram 5) A.) Attach the Butterfly Support Frame (#18) to the front of Right Vertical Beam (#21). Attach the Butter Pulley Support (#74) to the back of Right Vertical Beam. Align the holes. Secure them together with two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraf...

Page 11 - DIAGRAM

STEP 6 (See Diagram 6) A.) Attach the Vertical Press Frame (#78) to the Rear Vertical Beam (#50). Secure it with a M10 x 4 7/8” Vertical Press Axle (#81), two ∅ ¾” Washers (#6), and two M10 x 1” Allen Bolts (#56). B.) Place the Vertical Press Frame rest onto the ∅ 1 ½” Rubber Bumper (#83). DIAGRAM 6...

Page 13 - UPPER CABLE LOOP DIAGRAM

STEP 7 (Upper Cable Loop & Diagram 7) A.) Attach the 108” Upper Cable (#93) to the front opening on the Upper Frame (#8). Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one M10 Aircraft Nut (#5). Draw the Cable towards the bac...

Page 14 - DIAGRAM 7

Page 15 - BUTTERFLY CABLE LOOP DIAGRAM

STEP 8 (See Butterfly Cable Loop & Diagram 8) A.) Attach the 83” Butterfly Cable (#95) to the slot on the back of Left Butterfly (#20). Draw the Cable through the slot then to the open left Swivel Pulley Bracket (#72). B.) Attach a Pulley (#79) to the bracket. Secure it with one M10 x 2” Allen B...

Page 16 - DIAGRAM 8

Page 17 - FRONT PRESS CABLE LOOP DIAGRAM

STEP 9 (See Front Press Cable Loop & Diagram 9) A.) Attach the 247” Front Press Cable (#94) to the lower opening on the Leg Developer (#40). B.) Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one M10 Aircraft Nut (#5). C.) Dra...

Page 18 - DIAGRAM 9

Page 19 - LEG PRESS CABLE LOOP DIAGRAM

STEP 10 (See Leg Press Cable Loop & Diagram 10) A.) Attach one end of the 82” Leg Press Cable (#96) to the open slot on the back of the Leg Press Frame (#84). Secure it with one M10 x 2 ½” Allen Bolt (#10), two ∅ ¾” Washers (#6), and one M10 Aircraft Nut (#5). B.) Draw the Cable to the front ope...

Page 24 - PARTS LIST

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Lat Bar Grip 2 2 Lat Bar 1 3 Chain 4 4 C-clip 6 5 M10 Aircraft Nut 52 6 ∅ ¾” Washer 82 7 Bracket 3 8 Upper Frame 1 9 1 ¾” Square End Cap 17 10 M10 x 2 ½” Allen Bolt 8 11 Pulley Bushing 10 12 M6 x 1 5/8” Hex Bolt 2 13 ∅ 1 3/8” Lock Ring 2 14 M6 Aircraft Nut 2 15 ...

Page 25 - WEIGHT RESISTANCE CHART; ue for butterfly is for each arm.

WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Low Pulley 40 54 68 80 93 105 116 127 138 Lat Pull 40 55 70 80 90 100 110 120 130 Butterfly 50 55 60 67 74 80 93 106 120 Leg Press 80 107 135 160 185 210 232 254 275 Front Press 54 80 107 116 125 135 162 189 215 Vertical Press 45 60 76 9...

Page 26 - LIMITED WARRANTY

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's...

Impex CR 5 - Manual

Table of Contents:

Summary

Other Impex Models