Page 2 - Product overview
Contents Introduction..................................................................... 2Safety..............................................................................4Assembly...................................................................... 10Operation....................................
Page 4 - Safety; Safety definitions
• the product is incorrectly repaired.• the product is repaired with parts that are not from the manufacturer or not approved by the manufacturer. • the product has an accessory that is not from the manufacturer or not approved by the manufacturer. • the product is not repaired at an approved servic...
Page 5 - Personal protective equipment
• Look around the work area to make sure that no persons, animals or objects have a negative effect on the safety of the operation of the product. • Look around the work area to make sure that no persons or animals touch the cutting attachment or are hit by objects that are ejected from the cutting ...
Page 6 - Safety devices on the product
• Use clothing made of a strong fabric. Always use heavy, long pants and long sleeves. Do not use loose clothing that can catch on twigs and branches. Do not use jewelry, short pants or sandals. Do not go with bare feet. Put your hair up safely above shoulder level. • Keep first aid equipment near. ...
Page 10 - Assembly; Introduction
• Make sure that the engine is cool before you refuel.• Before you refuel, open the fuel tank cap slowly and release the pressure carefully. • Make sure there are sufficient airflow when refueling and mixing fuel (petrol and two-stroke oil) or draining the fuel tank. • Fuel and fuel vapor are highly...
Page 11 - To attach the trimmer guard or combination
To assemble the handlebar 1. Put the handlebar into the bracket. 2. Make sure that the holes for the knob align.3. Attach the knob but do not tighten fully.4. Adjust the handlebar to put the product in a good operation position. 5. Tighten the knob fully. To assemble the cutting equipment The cuttin...
Page 14 - Quick release function of the harness; Operation
5. Adjust the shoulder strap until the weight is equal on your shoulders. 6. Adjust the height of the suspension point. For forestry clearing, the correct height of the suspension is approximately 10 cm below your hip. Refer to Correct balance of the product on page 16. Quick release function of the...
Page 15 - Fuel; Gasoline
head and cutting attachment guard if they have been hit or if they have cracks. Fuel This product has a two-stroke engine. CAUTION: Incorrect type of fuel can result in engine damage. Use a mixture of gasoline and two-stroke oil. Gasoline CAUTION: Always use a quality gasoline/oil mixture of at leas...
Page 16 - To fill the fuel tank; Work position
1. Fill half the quantity of the gasoline to be used.2. Add the full quantity of oil and mix (shake) the fuel mixture. 3. Add the remaining quantity of gasoline.4. Carefully mix (shake) the fuel mixture and fill the fuel tank of the product. 5. Empty and clean the fuel tank if you do not use the pro...
Page 18 - To fell a tree to the left
blade thrust. The risk increases with the thickness of the branch that is cut. General work instructions WARNING: Be careful when you cut a tree that is in tension. It can spring back to its normal position before or after the cut and hit you or the product, and cause injury. • Clear an open space a...
Page 19 - To fell large trees; Brush cutting with a saw blade
3. Pull the saw blade forward with a fast movement. To fell large trees Large trees must be cut from 2 sides.1. Examine in which direction the tree will fall.2. Apply full throttle.3. Do the first cut on the side of the tree to which it will fall. 4. Cut through the tree from the other side. CAUTION...
Page 20 - Grass trimming with a trimmer head; To trim the grass
• Keep the support cup with a light pressure against the ground to make sure that the grass blade does not hit the ground. • Obey these instructions to decrease the risk that cut material winds around the grass blade:a) Apply full throttle.b) Do not move the grass blade through cut material when you...
Page 21 - To sweep the grass; Maintenance
3. Move the product from side to side when you cut grass. Use full speed. To sweep the grass The airflow from the rotating trimmer line can be used to remove cut grass from an area.1. Hold the trimmer head and the trimmer line parallel to the ground and above the ground. 2. Apply full throttle.3. Mo...
Page 27 - Troubleshooting; The engine does not start; Transportation, storage and disposal; Transportation and storage
Troubleshooting The engine does not start Check Possible cause Procedure Stop switch. The stop switch is in the stop posi- tion. Let an approved service agent re- place the stop switch. Starter pawls. The starter pawls cannot move free- ly. Remove the starter cover and clean around the starter pawls...
Page 28 - Disposal; Technical data
• In order to prevent unintentional start of the engine, the spark plug cap must always be removed during long-term storage if the product is not under close supervision and when you perform all service measures. • Allow the product to cool before you put in storage. Disposal • Obey the local recycl...
Page 29 - Accessories
535RX 535RXT Sound levels 2 Equivalent sound pressure level at the operator’s ear, measured according to EN ISO 11806 and ISO 22868, dB(A): Equipped with trimmer head (original) 95 95 Equipped with grass blade (original) 95 95 Vibration levels 3 Equivalent vibration levels (a hv,eq ) at handles, mea...
Page 30 - Declaration of Conformity; EU Declaration of Conformity
Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares on our sole responsibility that the product: Description Brush cutters Brand Husqvarna Type/Model 535RX, 535RXT Identification Serial numbers dating from 2022 and onward...
Page 31 - UK Declaration of conformity
UK Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares on our sole responsibility that the product: Description Brush cutters Brand Husqvarna Type / Model 535RX, 535RXT Identification Serial numbers dating from 2022 and onwards complies fully with th...
