Page 2 - Intended use
Contents Introduction..................................................................... 2Safety..............................................................................4Assembly...................................................................... 12Operation....................................
Page 4 - Safety; Safety definitions; Work area safety
Double insulation. Safety Safety definitions The definitions below give the level of severity for each signal word. WARNING: Injury to persons. CAUTION: Damage to the product. Note: This information makes the product easier to use. General machine safety warnings WARNING: Read all safety warnings an...
Page 6 - Causes and operator prevention of kickback; General safety instructions
ladders may cause a loss of balance or control of the chain saw. • When cutting a limb that is under tension be alert for spring back. When the tension in the wood fibres is released the spring loaded limb may strike the operator and/or throw the chain saw out of control. • Use extreme caution when ...
Page 10 - Battery safety
Pull the front hand guard rearward to disengage the chain brake. A kickback can be very sudden and intense. Most kickbacks are small and do not always engage the chain brake. If a kickback occurs when you use the product, hold tightly around the handles and do not let go. The front hand guard also d...
Page 11 - Safety instructions for the cutting equipment
product on page 35. The batteries are software encrypted. • Use the BLi batteries that are rechargeable as a power supply for the related Husqvarna products only. Refer to Approved batteries for the product on page 35. To prevent injury, do not use the battery as a power supply for other devices. • ...
Page 12 - Assembly; To assemble the guide bar and saw
• Use protective gloves when you use or do maintenance on the saw chain. A saw chain that does not move can also cause injuries. • Keep the cutting teeth correctly sharpened. Obey the instructions and use the recommended file gauge. A saw chain that is damaged or incorrectly sharpened increases the ...
Page 13 - Operation; Introduction
4. Make sure that the edges of the cutting links are turned forward on the top edge of the guide bar. 5. Make sure that the edges of the cutting links face forward on the top edge of the guide bar. 6. Assemble the drive sprocket cover and steer the chain adjuster pin to the hole in the guide bar. 7....
Page 15 - Common questions about kickback; To start the product
use the product when the kickback occurs that causes the direction of the movement. Kickback only occurs if the kickback zone of the guide bar touches an object. Do not let the kickback zone touch an object. A smaller bar tip radius decreases the force of the kickback.Use a low kickback saw chain to...
Page 17 - To use the cutting technique; To use the spiked bumper
• To cut on the push stroke is when you cut with the top of the guide bar. The saw chain pushes the product in the direction of the operator. WARNING: If the saw chain is caught in the trunk, the product can be pushed at you. Hold the product tightly and make sure that the kickback zone of the guide...
Page 18 - To cut a trunk that has support on two ends
1. Cut on the push stroke approximately ⅓ through the trunk. 2. Cut through the trunk on the pull stroke until the two kerfs touch. To cut a trunk that has support on two ends WARNING: Make sure that the saw chain does not get caught in the trunk during cutting. Obey the instructions below. 1. Cut o...
Page 19 - To use the tree felling technique; To keep a safe distance
to a professional chainsaw operator before you continue. 2. Remove the limbs on the top of the trunk. a) Keep the product on the trunk and let the guide bar move along the trunk. b) Cut on the push stroke. 3. Remove the limbs on the left side of the trunk. a) Select the applicable cutting technique ...
Page 23 - Maintenance
7. Continue to cut more into the tree until the tree/ branch bends and the tension is released. 8. Cut the tree/branch from the opposite side of the bend, after the tension is released. Maintenance Introduction WARNING: Read and understand the safety chapter before you do maintenance on the product....
Page 24 - To do a check of the front hand guard
Maintenance Before use Weekly Monthly Clean the external parts of the product. X Make sure that the power trigger and the power trigger lockout function correctly from a safety point of view. X Clean the chain brake and make sure that it operates safely. Make sure that the chain catcher is not damag...
Page 26 - Information about the guide bar and saw chain
2. Press the start/stop button again.3. Make sure that the product stops when you press and hold the button. The green LED will go off. To do a check of the battery and the battery compartment 1. Clean the battery and the battery compartment with a soft brush. 2. Make sure that the cooling slots and...
Page 29 - To adjust the tension of the saw chain; To adjust the tension of the saw chain (535i; To do a check of the saw chain
depth gauge setting after each third operation that you sharpen the cutting teeth.We recommend that you use our depth gauge tool to receive the correct depth gauge setting and bevel for the depth gauge. 1. Use a flat file and a depth gauge tool to adjust the depth gauge setting. Only use a Husqvarna...
Page 31 - To do a check of the guide bar; Troubleshooting; Keypad
To do a check of the guide bar 1. Make sure that the oil channel is not blocked. Clean if it is necessary. 2. Examine if there are burrs on the edges of the guide bar. Remove the burrs using a file. 3. Clean the groove in the guide bar. 4. Examine the groove in the guide bar for wear. Replace the gu...
Page 32 - Transportation, storage and disposal; Transportation and storage
Battery Problem Possible faults Possible solution Green LED flashes. Low battery voltage. Charge the battery. Red error LED flashes. The battery is empty. Charge the battery. Temperature deviation. Use the battery in temperatures between -10°C (14°F) and 40°C (104°F). Overvoltage. Remove the battery...
Page 33 - Technical data
for electrical and electronic equipment. This helps to prevent damage to the environment and to persons.Speak to local authorities, domestic waste service or your dealer for more information. Note: The symbol shows on the product or package of the product. Technical data Technical data 535i XP Motor...
Page 34 - Accessories; Guide bar and saw chain combinations
535i XP Saw chain/guide bar Recommended bar lengths, inch/cm 10-14/25-35 Usable cutting length, inch/cm 9-13/23-33 Type of drive sprocket/number of teeth Spur/7 Maximum chain speed / (savE), m/s 20 (15) Accessories Guide bar and saw chain combinations The following cutting attachments are approved f...
Page 35 - Approved batteries for the product; Approved battery chargers
SP21G 5/32 in / 4.0 mm 60° 30° 0° 0.025 in / 0.65 mm 595 00 46-01 595 00 47-01 Approved batteries for the product Battery BLi200/BLi200X 40-B220X Type Lithium-ion Lithium-ion Battery capacity, Ah 5.2 6 Nominal voltage, V 36 36 Weight, lb/kg 2.9/1.3 1.4 Approved battery chargers Battery charger QC330...
Page 36 - Declaration of Conformity; EU Declaration of Conformity
Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated chainsaw Brand Husqvarna Type / Model 535i XP Identification Serial numbers dating from 2022 and...
Page 37 - UK Declaration of Conformity
UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated chainsaw Brand Husqvarna Type / Model 535i XP Identification Serial numbers dating from 2022 and onwards complies fully wi...
