Honeywell T8501- Manual
Honeywell T8501– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – WIRING; CAUTION
- Page 3 – Fig. 4. Typical hookup in heat and cool system with; Mounting Thermostat
- Page 4 – Using Thermostat Keys; SETTINGS; System and Fan Settings; Temperature Settings; INSTALLER SETUP
- Page 7 – INSTALLER SYSTEM TEST
- Page 9 – THERMOSTAT INFORMATION; Outdoor Temperature Sensor
- Page 10 – TROUBLESHOOTING GUIDE; Symptom
® U.S. Registered Trademark
Copyright © 2004 Honeywell •
• All Rights Reserved
INSTALLATION INSTRUCTIONS
69-0925-4
T8501
Microelectronic Thermostats
APPLICATION
The T8501 Microelectronic Thermostats provides electronic control of 24 Vac single-stage heating and cooling
systems. Refer to Table 1 for a general description of the thermostat. All T8501 thermostats require a common wire to
supply power.
MERCURY NOTICE
If this control is replacing a control that contains
mercury in a sealed tube, do not place your old
control in the trash. Dispose of properly.
Contact your local waste management authority
for instructions regarding recycling and the
proper disposal of the old control.
INSTALLATION
When Installing this Product...
1.
Read these instructions carefully. Failure to follow
the instructions can damage the product or cause
a hazardous condition.
2.
Check the ratings given in the instructions and on
the product to make sure the product is suitable for
your application.
3.
Installer must be a trained, experienced service
technician.
4.
After completing installation, use these instructions
to check out the product operation.
Location
Install the thermostat about 1.5m (5 ft) above the floor in
an area with good air circulation at average temperature.
See Fig. 1.
Do not install the thermostat where it can be affected by:
— drafts, or dead spots behind doors and in corners.
— hot or cold air from ducts.
— radiant heat from sun or appliances.
— concealed pipes and chimneys.
— unheated (uncooled) areas such as an outside wall
behind the thermostat.
Wallplate Installation
The thermostat can be mounted horizontally on the wall
or on a 2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.
Position wallplate horizontally on the wall or on a
2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.
1.
Position and level the wallplate (for appearance
only). The thermostat will function properly even
when not level.
2.
Use a pencil to mark the mounting holes.
See Fig. 2.
3.
Remove the wallplate from the wall and drill two
3/16 inch (76 mm) holes in the wall (if drywall) as
marked. For firmer material such as plaster, drill
two 7/32 inch (5.56 mm) holes. Gently tap anchors
(provided) into the drilled holes until flush with the
wall.
4.
Position the wallplate over the holes, pulling wires
through the wiring opening.
5.
Loosely insert the mounting screws into the holes.
6.
Tighten mounting screws.
Table 1. Description of T8501 Thermostats.
System
Changeover
System Selection
Fan
Selection
Comments
Heat-Cool
Automatic
Heat-Off-Cool-Auto
On-Auto
System and fan selections are done by
keyboard.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Honeywell T8501
Summary
T8501 MICROELECTRONIC THERMOSTATS 69-0925—4 2 Fig. 1. Typical location of thermostat. Fig. 2. Mounting the wallplate. WIRING All wiring must comply with local electrical codes and ordinances. Refer to Fig. 3 and 5 for typical hookup. A letter code is located near each terminal for identification. CA...
T8501 MICROELECTRONIC THERMOSTATS 3 69-0925—4 Fig. 4. Typical hookup in heat and cool system with one transformer. Fig. 5. Typical hookup in heat and cool system with two transformers. . Fig. 6. Correct wiring technique. Mounting Thermostat 1. Engage tabs at the top of the thermostat and wall-plate....
T8501 MICROELECTRONIC THERMOSTATS 69-0925—4 4 Using Thermostat Keys The thermostat keys are used to:• set the temperature, • display present setting, • configure Installer Setup, • check System-Test,• display outdoor temperature (select models), Select models have keys to:• set the system operation,...
