Honeywell T8400C1099- User Manual
Honeywell T8400C1099– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Wiring; IMPORTANT
- Page 3 – Rc
- Page 4 – stage heat pump system.; Mounting Thermostat to Wallplate; OPERATION; Setting FAN and SYSTEM Switches; FAN Switch; Fan switch settings are:
- Page 5 – Setting °F/°C Indication and Heat Cycle Rate; OPTIONAL SYSTEM CHECKOUT
- Page 6 – CHECKOUT; Heating; CAUTION; System
- Page 7 – Fan
- Page 8 – Automation and Control Solutions
® U.S. Registered Trademark
Copyright © 2002 Honeywell • • All Rights Reserved
INSTALLATION INSTRUCTIONS
69-1484-2
T8400C1099, T8401C1031
Electronic Thermostats
The T8400 and T8401 Thermostats provide single-stage,
non-programmable temperature control for 24V heating-
cooling systems with manual changeover from heat to
cool. Heating cycle rate is selectable at 1, 3, 4, 5, 6, 9, or
12 cph. Cooling cycle rate is fixed at 3 cph. Temperature
indication can be set for °F or °C.
The T8400 Thermostat is powered through the heating/
cooling system controls. The T8401 requires a common
wire for operation. Batteries are not required because
setpoints are held permanently by non-volatile memory.
The T8400 and T8401 models include a thermostat,
wallplate (for wiring and mounting thermostat) and
owner’s guide.
MERCURY NOTICE
If this control is replacing a control that contains
mercury in a sealed tube, do not place your old
control in the trash.
Contact your local waste management authority
for instructions regarding recycling and the
proper disposal of an old control containing
mercury in a sealed tube.
INSTALLATION
When Installing this Product…
1.
Read these instructions carefully. Failure to follow
them could damage the product or cause a hazard-
ous condition.
2.
Check the ratings given in the instructions and on
the product to make sure the product is suitable for
your application.
3.
Installer must be a trained, experienced service
technician.
4.
After installation is complete, check out product
operation as provided in these instructions.
CAUTION
Electrical Shock or Equipment Damage
Hazard.
Can shock individuals or short equipment
circuitry.
Disconnect power supply before installation.
Location
Install the thermostat about 5 ft (1.5m) above the floor in
an area with good air circulation at average temperature.
See Fig. 1. Do not install the thermostat where it can be
affected by:
— drafts or dead spots behind doors and in corners.
— hot or cold air from ducts.
— radiant heat from the sun or appliances.
— concealed pipes and chimneys.
— unheated (uncooled) areas such as an outside wall
behind the thermostat.
This thermostat is a precision instrument and was
carefully adjusted at the factory. Handle it carefully.
Mounting Wallplate to Wall
IMPORTANT
Level only for appearance. The thermostat func-
tions normally even when not level.
Mount the T8400 and T8401 with the screws provided
(see Fig. 2) as follows:
1.
Place the wallplate at the desired location on the
wall.
2.
Pull the thermostat wire through the entrance hole
on the wallplate.
3.
Fasten the wallplate to the wall using the anchors
and screws provided.
4.
After wiring the wallplate, plug the hole to prevent
drafts from affecting the thermostat; see Wiring
section.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Honeywell T8400C1099
Summary
T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS 69-1484-2 2 Fig. 1. Typical location of thermostat. Fig. 2. Mounting wallplate to wall. Setting Fan Operation (Fuel) Switch The fan operation (fuel) switch is preset at the factory in the F position. See Fig. 3. This is the correct setting for most syste...
T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS 3 69-1484-2 Fig. 4. Restrict wiring to shaded area (T8400C1099 shown). Fig. 5. Wiring connections (T8400C1099 shown). Fig. 6. Typical hookup of T8400C1099 in heat-cool system with single transformer. Fig. 7. Typical hookup of T8400C1099 in heat-cool syst...
T8400C1099, T8401C1031 ELECTRONIC THERMOSTATS 69-1484-2 4 Fig. 9. Typical hookup of T8401C1031 in heat-cool system. Fig. 10. Typical hookup of T8401C1031 in single- stage heat pump system. Mounting Thermostat to Wallplate 1. Engage the tabs at the top of the thermostat and wallplate. 2. Swing down t...
