Honeywell RLV3100- User Manual
Honeywell RLV3100– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PROBLEM
- Page 3 – Guide d’utilisateur; Thermostat non programmable; Applications; Installation à 4 fils
- Page 4 – PROBLÈMES
RLV3100
69-1917EF 7/24/06 1/2
The RLV3100 thermostat can be used to control an electric heating
system such as an electric baseboard heater, a radiant ceiling, a
radiant floor, a convector, etc.
The thermostat cannot be used with the following:
•
a resistive load under 2 A
•
a resistive load over 12.5 A
•
systems driven by a contactor or a relay (inductive load)
•
fan-forced heating systems
•
central heating systems
•
One (1) thermostat
•
Two (2) 6-32 mounting screws
•
Two (2) solderless connectors
TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN
POWER PANEL TO AVOID ELECTRIC SHOCK.
Loosen the screw
underneath the thermostat
and separate the front plate
from the base plate.
NOTE
: The screw cannot be
completely removed.
Connect the thermostat wires to the power and to the load using
solderless connectors for copper wires. The thermostat wires are not
polarized; meaning either wire can be connected to the load or to the
power supply.
NOTE
: All cables and connections must comply with local electrical
codes. This thermostat has tinned copper wires for line and load
connections. Special CO/ALR solderless connectors must be used if
these wires will be connected to aluminium conductors.
Mount the back plate to the electrical
box using the provided screws. Insert
the screws through the left or right pair
of mounting holes of the back plate.
Set the switch on the back of the
front plate to °C or °F to select
the temperature display format.
Re-install the front plate of
the thermostat on the base
plate and secure it in place
with the screw underneath
the thermostat.
NOTE
: If there is a protective film or sticker on the display, peel it off.
n
Applications
1.
o
Supplied Parts
2.
p
Installation Procedure
3.
Temperature
display
Temperature adjustment buttons
Percentage of
heating time *
* The thermostat displays the percentage of heating time required to
maintain the desired temperature. For example, is displayed when
heating is activated 40 percent of the time.
2-wire Installation
4-wire Installation
RLV3100
User Guide
Digital Non-programmable Thermostat
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Honeywell RLV3100
Summary
RLV3100 69-1917EF 7/24/06 2/2 Apply power to the heating system. Verify the installation by checkingthat the heater can be turned On and Off by raising and lowering thesetpoint using the buttons. ATTENTION : Keep the thermostat's air vents clean and free from obstructions at all times. The thermosta...
RLV3100 69-1917EF 7/24/06 1/2 RLV3100 Guide d’utilisateur Thermostat non programmable Le thermostat RLV3100 peut servir à commander un appareil dechauffage électrique tel qu’une plinthe chauffante, un plafond radiant,un plancher chauffant, un convecteur, etc.Ce thermostat ne peut pas être utilisé da...
RLV3100 69-1917EF 7/24/06 2/2 Mettre le système de chauffage sous tension. Vérifier l’installation ens’assurant que le système de chauffage puisse être activé etdésactivé en augmentant et en diminuant la température de consigneà l’aide des boutons . MISE EN GARDE : Garder les ouvertures d’aération d...
