Honeywell RCWL301A- Manual
Honeywell RCWL301A– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Installation instructions–RCWL301A
- Page 3 – Chime Position; Typical Connection; Diagram Application
- Page 4 – Specification
- Page 5 – RCWL301A Manual de instrucciones
- Page 7 – Posición de la campanilla; un pulsador del timbre cableado estándar; Abra el pulsador/convertidor del timbre; Presione el botón; Conexión promedio; Diagrama Aplicación; Especificación
- Page 8 – Automation and Control Solutions; Honeywell International Inc.; Se escuchan dos “tonos” después del sonido normal de la campanilla...; Verifique que el control de volumen no esté en la posición mínima.; Desecho y reciclaje
69-2139EFS—1
1
RCWL301A Instruction Manual
Premium Portable Wirefree Chime with Push, Converter, and Door Contacts
Thank you for choosing this Honeywell product. Please use the following instructions
to ensure correct installation and use. Keep these notes in a safe place for future
reference.
Checking Pack Contents
Unpack your chime kit and identify the following parts:
•
Chime
•
Wall mounting bracket
•
Bell push
•
Bell push/converter/extender
•
Door contacts
•
2x CR2032 battery for bell push and converter
•
4x mounting screws for door contacts
•
4x mounting screws for push/converter
•
2x mounting screws for chime
•
2x wall anchors
•
2x adhesive pads
•
Bell wire (for use with converter and door contact)
•
Self-adhesive icons
You will need:
•
3x LR6 ‘AA’ Alkaline batteries
•
Phillips screwdriver
•
Small flat bladed screwdriver
•
1/4-in. (6 mm) masonry drill
Safety
Before proceeding with the installation, please note the following safety warnings:
•
Always follow the manufacturer’s advice when using power tools and wear suitable
protective equipment (e.g. safety goggles) when drilling holes, etc.
•
Before drilling holes in walls, check for hidden electricity cables and water pipes.
The use of a cable/pipe locator is advisable if in doubt.
Quick Start
The bell push supplied with this kit is pre-programmed to operate with the chime. You
need to do the following to get started:
•
Open the bell push
•
Fit the push battery
•
Fit the chime batteries
•
Check the volume setting
When you operate the bell push, the chime will sound and the 1st icon will flash.
If you use the converter, an additional push or you want to assign a different
icon to your push, you will need to follow the Programming Procedure.
•
Open the bell push/converter/extender
•
Connect the push/converter/extender to the door contacts
•
Fit the push/converter/extender battery
•
Follow programming procedure to program push/converter/extender to the chime
When the door contacts (a normally closed circuit) are separated/opened the
alert will sound and the icon assigned to the converter will flash.
•
Mount the door contacts to the door and door frame.
•
Mount the push/converter/extender near the door frame.
Open the Bell Push
Insert a flat bladed screwdriver into the slot A at the base of the push. Carefully lever
the cover and base apart (Fig. 1).
Fit the Push Battery
Insert the CR2032 coin cell. Ensure the face marked ‘+’ is uppermost (Fig. 2).
Fit the Chime Batteries
To remove the chime battery cover, press at point B and slide the cover back 1/4 in. (5
mm), then lift off. Insert 3 x LR6 ‘AA’ alkaline batteries (not supplied). Observe polarity
as marked inside the battery compartment (Fig 3).
M27199
A
Fig. 1
M27153
CR2032
+
CR2032
+
Fig. 2
M27200
B
Fig. 3
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Honeywell RCWL301A
Summary
Installation instructions–RCWL301A 69-2139EFS—1 2 Sliding Window Release the catch (B) and slide open the window (Fig. 4). Volume Control The volume control is behind the sliding window on the front of the chime. Initially, set the control to mid-point. After you have tested your system, adjust to t...
Installation instructions–RCWL301A 69-2139EFS—1 3 Chime Position The Chime can be free standing or wall mounted using the wall mounting bracket provided. If wall mounting is preferred, screw the bracket to the wall (see Fig 7). The Chime hooks onto the wall bracket as illustrated. RPWL3045A Wireless...
Installation instructions–RCWL301A 69-2139EFS—1 4 Fix the push/converter/extender Mount using either the double-sided adhesive pad or the screws provided. (See Fig. 10 ). Test your converter before mounting. Avoid mounting to metal structures. Troubleshooting A ‘beep’ sound is heard in learn mode… •...
